• Journal of Powder Materials
• /
• v.20 no.4
• /
• pp.245-252
• /
• 2013

This study attempted to manufacture a Cu-Ga coating layer via the cold spray process and to investigate the applicability of the layer as a sputtering target material. In addition, changes made to the microstructure and properties of the layer due to annealing heat treatment were evaluated, compared, and analyzed. The results showed that coating layers with a thickness of 520 mm could be manufactured via the cold spray process under optimal conditions. With the Cu-Ga coating layer, the ${\alpha}$-Cu and $Cu_3Ga$ were found to exist inside the layer regardless of annealing heat treatment. The microstructure that was minute and inhomogeneous prior to thermal treatment changed to homogeneous and dense with a more clear division of phases. A sputtering test was actually conducted using the sputtering target Cu-Ga coating layer (~2 mm thickness) that was additionally manufactured via the cold-spray coating process. Consequently, this test result confirmed that the cold sprayed Cu-Ga coating layer may be applied as a sputtering target material.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.3
• /
• pp.243-249
• /
• 2016

The present work is for an evaluation of resistance to corrosion in steel coated with cementitious repair material, so that 3 cases of steel plate(Normal, Welding, Welding & coating case) are subjected to ICM(Impressed Current Method) for acceleration of corrosion for 7days. Tested and estimated corrosion ratio through Faraday's Law are compared, and the related flexural strength are evaluated. In Normal and Welding cases, similar level of corrosion ratio(70%) is evaluated, however only 17% level of corrosion ratio is evaluated in the Welding & coating case, which indicates that cementitious repair material is effective to anti-corrosion due to a block of chloride penetration. The flexural test results are consistent with those in accelerated corrosion test, which shows a significant flexural strength in Welding & coating case by 3.4times greater than the others. The cementitious material repair coating is evaluated to be effective to anti-corrosion in welding of steel plate.

• Korean Journal of Digital Imaging in Medicine
• /
• v.10 no.1
• /
• pp.13-19
• /
• 2008

Purpose : In sponge quality of the material in digital radiography environment coating because do position blocks two that do not become coating done positioning blocks two that do not become coating done positioning block and sponge quality of the material to testing bench image artifact's difference compare. Method of study : In digital radiography environment positioning block of different two products same sunshine or effect that image and positioning block artifact gents in image analyze. the target used positioning block 2 when examine hand, rib and examination condition did each differently according to used positioning block. reflex compared picture that do image and verify that examine first time. Result : 1. In sponge quality of the material coating in done product artifact appear. Did not appear in product that do not become coating. 2. Can know coating's existence, that artifact according to radish happens. 3. Quality of the material coating's existence, there was difference of slippage according to radish Conclusion : Quality of the material coating phenomenon that done positioning block thus, it may have to be considered that use after estimate degree that get in image.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.5
• /
• pp.80-86
• /
• 2005

High velocity oxy-fuel thermally sprayed coating of the WC-Co cermet material is a well-established process for modifying the surface properties of the structural components exposed to the corrosive and wear attacks. The hard WC phase in the coating resists to the wear while the soft metallic Co increases the adhesive and cohesive bonding properties. The coating properties deposited by the HVOF process are greatly dependent on the feedstock materials and processing parameters. The effects of the feedstock material and process coating parameters including the in-flight particle parameters and resultant coating microstructures were observed in this paper.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.123-126
• /
• 2009

This study is analyzed the effects of the number of use of aluminum form surface coating material on surface quality of concrete. The results can be summarized as follows. Surface roughness showed larger values with increase in the number of use. Values were larger in UP and AL compared to PE. While found to have bad influence on concrete surface quality, PA and W showed most excellent values for roughness. The number of surface pores increased with increasing number of use, and the number of pores on concrete surface was reduced by applying a remover. In terms of type of surface coating material, PA and W showed smallest number of pores in comparison to PE. In order to comprehensively improve surface quality of concrete, parallel use of PA coating material and remover is deemed most appropriate.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1453-1456
• /
• 2009

Transparent sol-gel hybrid dielectric material (hybrimer) coating films were fabricated by spin coating and photo or thermal curing of sol-gel derived oligosiloxane resins. Hybrimer coating films are suitable as the passivation layer of TFT in AMLCD due to low dielectric constant, small loss tangent, low leakage current density, high transmittance and thermal stability.

• Plant Journal
• /
• v.6 no.4
• /
• pp.63-71
• /
• 2010

The best way to prevent the corrosion of piston rod is a selection of quality of the material and method of construction which minimize the porosity. The high velocity oxy fuel(HVOF) method, which generates lower porosity than existing plasma spray, was applied to ceramic laminated bond layer. Porosity percentage fell to bellow 2%, lower than that of plasma spray at 7%. Coating material of ceramic-coated main layer was selected as the $Cr_2O_3$ affiliation material, which is more dense than $Al_2O_3$ affiliation. To fill up the pores formed after the coating process, we sealed the bond layer and main layer. Sealing process was performed twice, once after the coating and once after the grinding. Upon the anti-corrosion test on the sealed sample and on the non-sealed sample, it is confirmed that the sealed sample was not corroded for 1,000 hours while the non-sealed sample was corroded within 48 hours.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.129-132
• /
• 1998

In this paper, we have studied the effect of electron reflection on shadow mask on which tungsten oxide film is coated and have studied the variation of beam mislanding with coating thickness in CRT. We found the method to be able to control coating thicknessed and optimum coating thickness of tungsten oxide film was 1∼2$\mu\textrm{m}$. Mislanding of electron beam was reduced about 20∼48% with increasing coating thickness in CRT

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.146-149
• /
• 2006

We developed new FED cathode film material that has catalysis function for graphite nano fiber. Using the cathode film with catalyst, we can simplify the FED process. It is composed of Cr, Fe-Ni catalyst. Fabricating FED panel with the film, we confirmed good emission performance of the panel.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.148-150
• /
• 2017

For the improvement of the anti-fouling features of porcelain electrical insulators, in this study, the surface of an insulator was coated with a functional material to expand the insulator's self-cleanness. The anti-fouling and mechanical features of the functional film coating of ceramic substrates made from components like an electrical insulator were analyzed. The coating methods that were used were spray coating, dip coating, and fabric coating. Following the coating, the contact angle of the coated surface was measured, revealing that the spray coating method offered the lowest angle ($13.7^{\circ}$) and a strong hydrophilic feature. The anti-fouling analysis showed that the anti-fouling features improved as the contact angle decreased. The mechanical properties - hardness and adhesion - were both excellent at 9H and 5B, respectively, regardless of the coating method that was used.