• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.618-626
• /
• 2019

Stem cell therapy is not expected to bestow any therapeutic benefit because of the low engraftment rates after transplantation.Various cell-carrying scaffolds have been developed in order to overcome this problem. When the scaffold is formed by 3-dimensional (3D) printing, it is possible to create various shapes of scaffolds for specific regions of injury. At the same time, scaffolds provide stem cells as therapeutic-agents and mechanically support an injured region. PCL is not only cost effective, but it is also a widely used material for 3D printing. Therefore, rapid and economical technology development can be achieved when PCL is printed and used as a cell carrier. Yet PCL materials do not perform well as cell carriers, and only a few cells survive on the PCL surface. In this study, we tried to determine the conditions that maximize the cell-loading capacity on the PCL surface to overcome this issue. By applying a plasma treated condition and then collagen coating known to improve the cell loading capacity, it was confirmed that the 3% collagen coating after plasma treatment showed the best cell engraftment capacity during 72 hours after cell loading. By applying the spheroid cell culture method and scaffold structure change, which can affect the cell loading ability, the spheroid cell culture methods vastly improved cell engraftment, and the scaffold structure did not affect the cell engraftment properties. We will conduct further experiments using PCL material as a cell carrier and as based the excellent results of this study.

• Development and Reproduction
• /
• v.10 no.1
• /
• pp.63-73
• /
• 2006

This study aimed to find out suitable culture conditions for the differentiation of human amniotic membrane-derived stem cells(HAM) into hepatocyte-like cells. Almost homogenous population of fibroblast-like cells was successfully isolated from the amniotic membrane. In comparison to the non-coated plates and in the absence of insulin/transferrin/selenium(ITS), HAM cultured on the fibronectin-coated plates and in the presence of ITS showed the more intense immunocytochemical staining against the albumin. Addition of both fibroblast growth factor(FGF)-1 and -2 to the differentiation medium gave stronger staining compared to the treatment with FGF-1 or -2 alone. Periodic acid Schiff's base staining of glycogen and morphological turnover of fibroblast-like appearance of HAM into round shape matched the results of immunocytochemical studies. When the efficiency of two-step culture method was examined on the differentiation of HAM into hepatocyte-like cells, all of the results of immunocytochemical staining, periodic acid Schiff's staining and morphological change exhibited effective hepatic differentiation of HAM compared to the continuous culture method. Immunoblot analyses of HAM- conditioned media against the albumin showed that the culture of HAM in the presence of both ITS and fibronectin always gave a stronger staining intensity than those in the absence of them, and that the addition of ether mixture of FGF-4 and either FGF-2 or transforming growth $factor(TGF)-{\alpha}$ to the culture medium significantly enhanced the albumin secretion by HAM. Based on these observations, it is suggested that HAM could differentiate into hepatocyte-like cells under a culture condition consisting of fibronectin and ITS, and addition of FGF-4 with either one of FGF-2 or $TGF-{\alpha}$ could enhance the hepatic differentiation of HAM.

• Polymer(Korea)
• /
• v.32 no.4
• /
• pp.322-327
• /
• 2008

In this study, a multi-layered pellet was composed of a seed layer including a water-swellable agent and a drug layer containing doxazosin as a model drug, a porous membrane and a castor oil layer to control drug release. The pellet is prepared by a fluidized bed coating method. To confirm drug release from polymer blending in multi-layered pellet system, it is prepared by containing different ratio such as hydroxypropylmethylcellulose (HPMC) : ethyl cellulose (EC) in drug layer and cellulose acetate(CA) : Eudragit RS in membrane. Also, to confirm the effect of oil in drug release, castor oil is coated. As a result, we observed regularly spherical pellet with diameter of $1500{\mu}m$. Release pattern of drug is confirmed by dissolution tester in aqueous media. The more the ratio of EC in drug layer, CA in membrane, and castor oil layer in pellet, the less the drug release is observed. Formation and the amount of pores in membrane is observed by SEM.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.222-222
• /
• 2012

Metal oxide gas sensors based on semiconductor type have attracted a great deal of attention due to their low cost, flexible production and simple usability. However, most works have been focused on n-type oxides, while the characteristics of p-type oxide gas sensors have been barely studied. An investigation on p-type oxides is very important in that the use of them makes possible the novel sensors such as p-n diode and tandem devices. Monoclinic cupric oxide (CuO) is p-type semiconductor with narrow band gap (~1.2 eV). This is composed of abundant, nontoxic elements on earth, and thus low-cost, environment-friendly devices can be realized. However, gas sensing properties of neat CuO were rarely explored and the mechanism still remains unclear. In this work, the neat CuO layers with highly ordered mesoporous structures were prepared by a template-free, one-pot solution-based method using novel ink solutions, formulated with copper formate tetrahydrate, hexylamine and ethyl cellulose. The shear viscosity of the formulated solutions was 5.79 Pa s at a shear rate of 1 s-1. The solutions were coated on SiO2/Si substrates by spin-coating (ink) and calcined for 1 h at the temperature of $200{\sim}600^{\circ}C$ in air. The surface and cross-sectional morphologies of the formed CuO layers were observed by a focused ion beam scanning electron microscopy (FIB-SEM) and porosity was determined by image analysis using simple computer-programming. XRD analysis showed phase evolutions of the layers, depending on the calcination temperature, and thermal decompositions of the neat precursor and the formulated ink were investigated by TGA and DSC. As a result, the formation of the porous structures was attributed to the vaporization of ethyl cellulose contained in the solutions. Mesoporous CuO, formed with the ink solution, consisted of grains and pores with nano-meter size. All of them were strongly dependent on calcination temperature. Sensing properties toward H2 and C2H5OH gases were examined as a function of operating temperature. High and fast responses toward H2 and C2H5OH gases were discussed in terms of crystallinity, nonstoichiometry and morphological factors such as porosity, grain size and surface-to-volume ratio. To our knowledge, the responses toward H2 and C2H5OH gases of these CuO gas sensors are comparable to previously reported values.

• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.660-667
• /
• 2010

In this research polyimide, Matrimid 5218, hollow fiber membrane was used to recover sulfur hexafluoride($SF_6$) which is one of the six greenhouse gases from $N_2/SF_6$ mixture gas. Fibers were spun from using dry-wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a sponge-like substructure. The developed module had a permeance of 0.78-1.36 GPU for $N_2$ with $N_2/SF_6$ selectivity of 2.44-5.08 at various pressure and temperature. For recovery of $SF_6$, a membrane module and 10 vol.% $SF_6$ from $N_2/SF_6$ mixture gas was used. The effects of various operating condition such as pressure, temperature, and retentate side flow rate were tested. When pressure and temperature were increased and retentate flow rate was decreased, the $SF_6$ purity in recovered gas was increased up to 37.5 vol.% with decreasing recovery ratio. When retentate flow rate was increased pressure and temperature was decreased, the $SF_6$ recovery ratio in retentate side was increased up to 89% with decreasing the $SF_6$ purity in retentate side.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.2
• /
• pp.14-23
• /
• 1998

The present study investigates numerically particle laden flow through compressor cascade. In general, a lot of turbine engines are affected by various particles which are suspending in the atmosphere. Especially in the case of aircraft aviating in volcanic, industrial and desert region including many particles, each components of engine system are damaged severely. That damage modes are erosion of compressor binding and rotor path components, partial or total blockage of cooling passage and engine control system degradation.. Initial damages can not be serious but cumulation of damages influences on safety of aircraft control and economical maintenance cost of engine system can be increased. When dust, materials and volcanic particles in the atmosphere flow in the compressor, it is necessary to predict damaged and deposited region of compressor blades. To the various flow inlet angle, predictions of particles trajectory in compressor cascade by Lagrangian method are presented and impulses by impaction of particles at blade surface are calculated. By the definition of particle deposition efficiency, characteristics of particles impact are considered quantitatively. With these prediction and experimental data, erosion rates are predicted for two materials - ceramic, soft metal - on compressor blade surface. Improvements like coating of blade surface could be found, by above prediction.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.189-189
• /
• 2012

Lead sulfide (PbS) nanocrystal quantum dots (NQDs) are promising materials for various optoelectronic devices, especially solar cells, because of their tunability of the optical band-gap controlled by adjusting the diameter of NQDs. PbS is a IV-VI semiconductor enabling infrared-absorption and it can be synthesized using solution process methods. A wide choice of the diameter of PbS NQDs is also a benefit to achieve the quantum confinement regime due to its large Bohr exciton radius (20 nm). To exploit these desirable properties, many research groups have intensively studied to apply for the photovoltaic devices. There are several essential requirements to fabricate the efficient NQDs-based solar cell. First of all, highly confined PbS QDs should be synthesized resulting in a narrow peak with a small full width-half maximum value at the first exciton transition observed in UV-Vis absorbance and photoluminescence spectra. In other words, the size-uniformity of NQDs ought to secure under 5%. Second, PbS NQDs should be assembled carefully in order to enhance the electronic coupling between adjacent NQDs by controlling the inter-QDs distance. Finally, appropriate structure for the photovoltaic device is the key issue to extract the photo-generated carriers from light-absorbing layer in solar cell. In this step, workfunction and Fermi energy difference could be precisely considered for Schottky and hetero junction device, respectively. In this presentation, we introduce the strategy to obtain high performance solar cell fabricated using PbS NQDs below the size of the Bohr radius. The PbS NQDs with various diameters were synthesized using methods established by Hines with a few modifications. PbS NQDs solids were assembled using layer-by-layer spin-coating method. Subsequent ligand-exchange was carried out using 1,2-ethanedithiol (EDT) to reduce inter-NQDs distance. Finally, Schottky junction solar cells were fabricated on ITO-coated glass and 150 nm-thick Al was deposited on the top of PbS NQDs solids as a top electrode using thermal evaporation technique. To evaluate the solar cell performance, current-voltage (I-V) measurement were performed under AM 1.5G solar spectrum at 1 sun intensity. As a result, we could achieve the power conversion efficiency of 3.33% at Schottky junction solar cell. This result indicates that high performance solar cell is successfully fabricated by optimizing the all steps as mentioned above in this work.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.4
• /
• pp.39-46
• /
• 2017

This paper presents the fabrication of ceramic insulation layer on metallic heat spreading substrate, i.e. an insulated metal substrate, for planar type heater. Aluminum alloy substrate is preferred as a heat spreading panel due to its high thermal conductivity, machinability and the light weight for the planar type heater which is used at the thermal treatment process of semiconductor device and display component manufacturing. An insulating layer made of ceramic dielectric film that is stable at high temperature has to be coated on the metallic substrate to form a heating element circuit. Two technical issues are raised at the forming of ceramic insulation layer on the metallic substrate; one is delamination and crack between metal and ceramic interface due to their large differences in thermal expansion coefficient, and the other is electrical breakdown due to intrinsic weakness in dielectric or structural defects. In this work, to overcome those problem, selected metal oxide buffer layers were introduced between metal and ceramic layer for mechanical matching, enhancing the adhesion strength, and multi-coating method was applied to improve the film quality and the dielectric breakdown property.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.2
• /
• pp.70-74
• /
• 2009

Effect of the processing variables on the formation of $Pb(Sc_{1/2}Nb_{1/2})O_3$(hereafter PSN) thin layers prepared on Pt(111)/Ti/$SiO_2$/Si substrates using the sol-gel and the spin coating method has been studied. After each deposition, the coated films were heated at $370^{\circ}C$ for 5 min. Then they were finally sintered at temperature range of $600{\sim}700^{\circ}C$ by RTA(rapid thermal annealing). The final multilayered films showed a (111) preferred orientation. On a while, the layer-by-layer crystallization of multilayered amorphous thin films without the intermediate heating exhibited a (100) preferred orientation. In case of heat treatment in the tube furnace with the heating rate of $4^{\circ}C/min$, (100) and (111) oriented thin layers were formed simultaneously. The microstructure of the deposited films were dense and crack-free with thickness of 300nm, irrespective of the processing variables.

• The Journal of the Korean dental association
• /
• v.53 no.10
• /
• pp.688-695
• /
• 2015

Purpose: The institutionalized elderly have placed the most vulnerable state, and the report about the oral health status of the institutionalized elderly was scarce. The aims of the current study were to investigate the oral health status of institutionalized elderly. Materials and methods: The survey of the oral health status was carried out on 487 institutionalized elderly from 4 longterm care facilities of Seoul metropolitan city, Gyunggi province, and Gangwon province in Korea. Results: The prevalence of dental caries, root caries, and dental calculus of the institutionalized elderly was 19.2%, 15.3%, and 23.7%, respectively. The percentage of edentulism among the institutionalized elderly was 26.2%. Those who had poor oral hygiene and tongue coating were 43.9% and 90.5%, respectively. The percentages wearing complete and removable partial denture on maxilla were 12.8% and 3.3%, respectively. The percentages wearing complete and removable partial denture on mandible were 7.8% and 5.6%, respectively. The percentages of institutionalized elderly needing complete and removable partial denture on maxilla were 29.7% and 27.2%, respectively. The percentages of institutionalized elderly needing complete and removable partial denture on mandible were 24.5% and 30.9%, respectively. Conclusion: The oral health stuatus of institutionalized elderly was poor. For the oral health promotion of elderly in longterm care facilities, it is essential to educate nurses and caregivers about the importance of the oral health and oral hygiene method.