• 한국전기전자재료학회논문지
• /
• 제30권1호
• /
• pp.32-36
• /
• 2017

The Ag thin film of YBCO (yttrium barium copper oxide) CC (coated conductor) protect the YBCO layer and, at the same time, affects the electrical characteristics of the YBCO CC. Therefore, YBCO CC with the commercialization of the Ag thin film layers makes it easy to establish a process, it can lead to a variety of characteristic changes in YBCO CC. In this paper, plasma surface treatment was carried out to facilitate the deposition of the Ag thin film and the deposition process of YBCO CC. Surface roughness from the test results was increased as the time of the plasma surface treatment increased from 5 to 20 minutes. On the other hand, the surface roughness was decreased for the time of the plasma surface treatment over 20 minutes. Furthermore, after depositing, the increasing of deposit amount and reduced lifting phenomenon showed a similar tendency with the rise time of surface roughness.

• 한국환경과학회지
• /
• 제14권8호
• /
• pp.785-792
• /
• 2005

In order to reduce roadside and indoor air pollution for volatile organic compounds VOC), it may be necessary to apply photocatalyst-coated construction materials. This study evaluated the technical feasibility of the application of $TiO_2$ photocatalysis for the removal of VOC present in roadside or indoor air. The photocatalytic removal of five target VOC was investigated: benzene, toluene, ethyl benzene and o,m,p-xylenes. Variables tested for the current study included ultraviolet(UV) light intensity coating materials, relative humidity (RH), and input concentrations. Prior to performing the parameter tests, adsorption of VOC onto the current experiment was surveyed, and no adsorption was observed. Stronger UV intensity provided higher photocatalytic destruction(PCD) efficiency of the target compounds. For higher humidity, higher PCD efficiency was observed. The PCD efficiency depended on coating material. Contrary to certain previous findings, lower PCD efficiencies were observed for the experimental condition of higher input concentrations. The current findings suggested that the four parameters tested in the present study should be considered for the application of photocatalyst-coated construction materials in cleaning VOC of roadside or indoor air.

• 한국전기전자재료학회논문지
• /
• 제11권9호
• /
• pp.711-717
• /
• 1998

BST(70/30) and BST(50/50) thin films were prepared by Sol-Gel method and studied about the microstructural and dielectric properties with Pt and ITO bottom electrodes. The stock solution was synthesized and spin coated on the Pt/Ti$SiO_2$/Si and Indium Tin Oxide(ITO)/ glass substrate. the coated films were dries at 350$^{\circ}C$ for 10 minutes and annealed at $750^{\circ}C$ for 1 hour for the crystallization. The thin films coated on ITO substrate were crystallized easily and the packing density and roughness of surface were better that those of films coated on Pt substrates. In the BST(50/50) composition the structural properties were similar to the BST(70/30) composition and grain size were decreased with increasing the contents of Sr. The dielectric constant was higher in the BST(50/50) composition compared with the BST(70/30) composition. Using the ITO substrate, the dielectric constant was higher than the Pt substrate while the dielectric loss was showed a reverse trend. The dielectric constant with and increase of temperature was decreased slowly.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 초전도 자성체 연구회
• /
• pp.38-41
• /
• 2003

상업용 Ag 판재 위에 cyclic 전위와 일정 전위를 인가하는 전기증착법으로 Tl-1223상 precursor 막을 증착하는 연구를 수행한 다음, 이를 이영역 전기로를 사용하여 열처리함으로써 고온초전도 coated conductors를 제조하는 연구를 수행하였다. 전기증착법으로 비교적 균질하고 치밀한 precursor막을 증착할 수 있었으며, 이 막을 $870^{\circ}C$에서 20분 동안 열처리하여 임계온도가 114 K이고 자속고정능력도 비교적 우수한 50%의 Tl-1223상과 50%의 Tl-1212상으로 구성된 고온초전도 도체를 제조할 수 있었다. 이로부터 아주 값싼 증착법인 전기증착법을 이용하여 후막의 고온초전도 도체를 제조할 수 있음을 증명하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.236-237
• /
• 2007

Lamination of coated conductor is important to commercialize for electrical stabilizer and mechanical support. It should be known the properties of soldering interface and the variation of superconductivity on coated conductor with various kinds of solders. $SmBa_2Cu_O_x$ thin films were deposited by co-evaporation method (EDDC, Evaporation using Drum in Dual Chambers). 4 kinds of solders were used to investigate interface properties of SmBCO conductors. In-Bi solder could maintain good connection.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.218-221
• /
• 2000

Currently, Bi-2223 HTS tape is capable of being fabricated in longer than 100m length by industrial processes. But there are some problems in heat treatment of the degree of longer than 100m tape, which is in term of volume occupied with specimen in furnace. The effects of ceramic coating with variable slurry states were studied in Bi-2223 high-temperature superconductor. The HTS tapes coated with oxide were prepared by using dip-coating method on slurry state. Critical current(I$_{c}$) of tapes coated with ceramic materials were equal with 11.5A at 77K after first heat treatment as different slurries. For final heat treatment, Critical current of HTS tapes coated with zirconia oxide mixed in PMMA and PVA organic solute were 20.8A at 77K. The breakdown voltage of HTS tapes coated with zirconia oxide were 3kV in air and 4~7kV in L$N_2$.>.

• 한국초전도ㆍ저온공학회논문지
• /
• 제10권3호
• /
• pp.23-26
• /
• 2008

Constructions of coated conductor which is differently from Bi-2223 is comprised multiple coatings on a base material or substrate and designed to achieve the highest degree of alignment possibility of the atoms in the superconductor material. In this study, we are measured and analyzed degradations of critical current according to diameter. In addition to study the effects of bending strain, we observed the AC loss of coated conductor and carried out analytical study for relation between Ic degradation and AC loss as well. The measurement of AC loss and numerical calculation was carried out based on Norris theory to compare with experimental results. The relationship between critical current and AC loss of HTS tapes with partial deformation by mechanical stress was studied. These results will amount the most important basis data in the of HTS cable, magnet, etc that winding work is required.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.269-275
• /
• 2000

The fretting wear characteristics of TiN coated Zircaloy-4 tube were investigated experimentally The fretting wear experiment was performed using TiN coated Zircaloy-4 tube as the fuel rod cladding material and uncoated Zircaloy-4 tube as one of grids. TiN coating is probably one of the most frequently and successfully used PVD coatings for the mitigation of fretting wear. In this study, TiN coating by PVD was employed for improvement of Zircaloy-4 tube fretting characteristics. The fretting tester was designed and manufactured for this experiment. TiN coated Zircaloy-4 tube was used as the moving specimen, uncoated ZircaBoy-4 tube as the stationary one. The number of cycles, slip amplitude and normal load were selected as main factors of fretting wear. The results of this research showed that the wear volume of TiN coated Zircaloy-4 tube increased as number of cycles, normal load and slip amplitude increase but the quantity of volume was lower than the case of uncoated Zircaloy-4 tube pairs.

• 한국산업융합학회 논문집
• /
• 제15권4호
• /
• pp.103-109
• /
• 2012

To enhance the cutting performance of high speed steel(HSS) endmill, single and multilayer coating is applied on the substrated of the HSS endmill. Coating material reduces cutting force and enhances resistance against abrasive wear. This paper presents the physical vapour deposition(PVD) coating technology and evaluate the PVD coated HSS endmill. The performance of coated HSS endmills are fifteen times better than uncoated HSS endmill on proposed cutting conditions. The TiAlN monolayer coated endmills(futura nano coating) are better than those of multilayer coated endmills(futura coating) on machined surface and tool wear.

• The Korean Journal of Ceramics
• /
• 제2권4호
• /
• pp.203-211
• /
• 1996

CVD diamond tools are becoming more widely used in industry as an economic alternative to polycrystalline diamond (PCD) for machining non-ferrous and non-metallic materials. Although CVD diamond-sheet tools have been on the market for several years, diamond-coated carbide inserts have become available only recently, with the successful resolution of long-standing adhesion problems. Diamond coating morphology on the rake surface of the tool affects chip formation favorably, whereas a microscopically rough, faceted morphology on the flank surface of the tool produces a rough workpiece finish. Workpiece finish can be improved by using a coated tool with a larger nose radius. The tool life provided by diamond-coated tools(~30 $\mu\textrm{m}$ thick) can meet or exceed that of PCD tools, depending on the characteristics of the workpiece material. When using diamond-coated carbide tools in milling, a sharp-edged PCD tool should be used in the wiper position of the cutter to minimize workpiece roughness and burr formation.