• Membrane Journal
• /
• v.28 no.5
• /
• pp.361-367
• /
• 2018

In this study, the nanofiltration (NF) composite membranes for the low pressure use were prepared using polyvinylidene fluoride (PVDF) hollow fiber membrane as a supporter. Poly styrene sulfonic acid (PSSA) and polyethyleneimine (PEI) were coated onto the PVDF membrane by both layer-by-layer and salting-out methods. To characterize the prepared NF membranes in terms of the flux and salt rejection, 100 mg/L feed solutions of NaCl, $MgCl_2$, and $CaSO_4$ were used at the flow rate of 1 L/min and the operating pressure of 2 bar at room temperature. The NF membranes coated with 20,000 ppm PSSA (ionic strength 1.0) solution for 3 minutes and then 30,000 ppm (ionic strength 0.1) solution for 1 minute were observed the best performance. The permeability and salt rejection were 38.5 LMH, 57.1% for NaCl, 37.9 LMH and 90.2% for $MgCl_2$ and 32.4 LMH and 54.6% for $CaSO_4$, respectively.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.2
• /
• pp.60-68
• /
• 2019

High-voltage operation of the lithium ion battery is one of the advantageous approaches to obtain high energy capacity without changing the conventional cell components and structure. However, operating at harsh condition inevitably results in severe side reactions at the electrode surface and structural disintegration of active material particles. Herein we coated layers composed of $Al_2O_3$ and ZnO on the electrode based on NCM using atomic layer deposition (ALD). Thicker layers of novel Al-doped ZnO (AZO) coating compared to conventional ALD coated layers are prepared. Cathode based on NCM with the varying AZO coating thickness are fabricated and used for coin cell assembly. Effect of ALD coating thickness on the charge-discharge cycle behavior obtained at high-voltage operation was investigated.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.4
• /
• pp.8-11
• /
• 2006

High temperature superconducting coated conductor has various buffer structures on Ni-W alloy. We comparatively studied the growth conditions of a multi buffer layer $(CeO_2/YSZ/CeO_2)$ and a single buffer layer$(CeO_2)$ on textured Ni-W alloy tapes. XRD data showed that the qualities of in-plane and out-of-plane textures of the two type buffer structures were good. Also, we investigated the properties of SmBCO superconducting layer that was deposited on the two type buffer structure. The SmBCO superconducting properties on the single and multi buffer structure showed different critical current values and surface morphologies. FWHM of In-plane and out-of-plane textures were $7.4^{\circ},\;5.0^{\circ}$ in the top CeO2 layer of the multi-buffer layers of $CeO_2/YSZ/CeO_2$, and $7.3^{\circ},\;5.1^{\circ}$ in the $CeO_2$ single buffer layer. $1{\mu}m-thick$ SmBCO superconducting layers were deposited on two type buffer layer. $I_c$ of SmBCO deposited on single and multi buffer were 90 A/cm, 150 A/cm and corresponding $J_c$ were $0.9MA/cm^2,\;1.5MA/cm^2$ at 77K in self-field, respectively.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.3
• /
• pp.5-8
• /
• 2007

All three buffer layers of $Y_2O_3$, YSZ, and $CeO_2$ have been deposited on the biaxially textured metal substrates using rf-sputtering method, The first 50-70nm thick $Y_2O_3$ films were grown epitaxially on biaxially textured metal substrates as a seed layer and followed by the diffusion barrier ${\sim}100nm$ thick YSZ and subsequent capping layer ${\sim}200nm$ thick $CeO_2$ deposited epitaxially on top of $Y_2O_3$ seed layer. The epitaxial orientation of all three layers were all (100) grown with rocking curve Full Width at Half Maximum(FWHM) of $4-5^{\circ}$ and in plane phi-scan FWHM of $6-8^{\circ}$ using X -ray diffraction analysis. The NiO phases formed during the $Y_2O_3$ seed layer deposition seem to degrade the crystallinity and roughen the surface morphology of the following layer observed by AFM(Atomic Force Microscopy). The buffered tapes were used as substrates for long length YBCO coated conductors with high critical current density $J_c$. The five multi-turn of metal tapes was employed to increase the thickness of films and production rate to compensate the low growth rate of rf-sputtering method.

• Journal of the Korean Professional Engineers Association
• /
• v.21 no.1
• /
• pp.5-12
• /
• 1988

The purpose of this paper is to investigate on the optimum coating thickness layer of TiC-Al$_2$O$_3$ coated cemented carbide tool. Chemical Vapor Deposition (CVD) of a thick film of TiC-A1$_2$O$_3$ on a cemented carbide produces an intermediate layer, $1.5mutextrm{m}$, 4.5${\mu}{\textrm}{m}$, 7.5${\mu}{\textrm}{m}$ 10.5${\mu}{\textrm}{m}$, 4 kind of TiC between the substrate and the $1.5mutextrm{m}$ constant thick A1$_2$O$_3$ coating. Experiments were carried out with the test relationship between coating thickness and shear angle, surface roughness, cutting force, microphotograph of crater wear, flank wear, tool life. From the experimental results, it was found that the optimum coating thickness of TiC-A1$_2$O$_3$ is 6${\mu}{\textrm}{m}$. Although the coating thickness layer 9${\mu}{\textrm}{m}$. 12${\mu}{\textrm}{m}$ have a much loger tool wear than an 3${\mu}{\textrm}{m}$, 6${\mu}{\textrm}{m}$ coating tool in cutting condition feed 0.05mm/rev, and the condition of feed 0.2mm/rev, 0.3mm/rev has upon in the shot time phenomenon of chipping.

• Nuclear Engineering and Technology
• /
• v.38 no.2
• /
• pp.139-146
• /
• 2006

An experimental study was performed to evaluate the effects of surface coating and an enhanced insulation structure on the downward facing boiling process and the critical heat flux on the outer surface of a hemispherical vessel. Steady-state boiling tests were conducted in the Subscale Boundary Layer Boiling (SBLB) facility using an enhanced vessel/insulation design for the cases with and without vessel coatings. Based on the boiling data, CHF correlations were obtained for both plain and coated vessels. It was found that the nucleate boiling rates and the local CHF limits for the case with micro-porous layer coating were consistently higher than those values for a plain vessel at the same angular location. The enhancement in the local CHF limits and nucleate boiling rates was mainly due to the micro-porous layer coating that increased the local liquid supply rate toward the vaporization sites on the vessel surface. For the case with thermal insulation, the local CHF limit tended to increase from the bottom center at first, then decrease toward the minimum gap location, and finally increase toward the equator. This non-monotonic behavior, which differed significantly from the case without thermal insulation, was evidently due to the local variation of the two-phase motions in the annular channel between the test vessel and the insulation structure.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.2
• /
• pp.7-10
• /
• 2004

A study regarding the epitaxial growth of single $Y_2O_3$ buffer layer on biaxially textured Ni and NiW substrates using pulsed laser deposition is presented. Different deposition conditions were employed and compared in order to obtain good epitaxial $Y_2O_3$ film, furthermore importantly, to obtain good YBCO superconducting films. Following YBCO film deposited by PLD on the top of $Y_2O_3$ films have a good structure and superconducting properties. The J$_{c}$ of YBCO films on $Y_2O_3$ /Ni and $Y_2O_3$ /NiW were $1.0{\times}10^6 A/cm^2 and 1.1\times}10^6 A/cm^2$<.TEX> at 77K and self-field respectively, which indicated that $Y_2O_3$ is a suitable candidate as a single buffer layer for the fabrication of YBCO coated conductor.r.

• Tribology and Lubricants
• /
• v.15 no.2
• /
• pp.184-192
• /
• 1999

Various compositions of$ Cr_2$$O_3$/Mo composite powders were fabricated using spray-drying method and plasma-spray coatings of these powders were prepared to understand their tribological properties. Experiments were conducted using a reciprocal type tribo-tester at room temperature under dry sliding condition. The worn surface of coated specimens were observed using SEM (Scanning Electron Microscopy) and chemical compositions were analyzed using XRD (X-ray Diffractometry) and XPS (X-ray Photoelectron Spectroscopy). The results showed that friction coefficient of the Mo added specimens were lower than that of $Cr_2$$O_3$specimen. However $Cr_2$$O_3$specimen showed the lowest wear loss. Wear protecting layer were observed at the worn surface of coated specimens with Mo addition. From the XPS analysis, the mixed phases of $Cr_2$$O_3$ $CrO_3$and $MoO_3$were founded in the wear protecting layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.268-268
• /
• 2012

Adsorption and desorption of toluene from bare and $TiO_2$-coated silica with a mean pore size of 15 nm was studied using breakthrough curves and temperature programmed desorption. Thicknesses of $TiO_2$ films prepared by atomic layer deposition on silica were < 2 nm, and ~ 5 nm, respectively. For toluene adsorption, both dry and humid conditions were used. $TiO_2$-thin film significantly improved toluene adsorption capacity of silica under dry condition, whereas desorption of toluene from the surface as a consequence of displacement by water vapor was more pronounced for $TiO_2$-coated samples with respect to the result of bare ones. In the TPD experiments, silica with a thinner $TiO_2$ film (thickness < 2 nm) showed the highest reactivity for toluene oxidation to $CO_2$ in the absence and presence of water. We show that the toluene adsorption and oxidation reactivity of silica can be controlled by varying thickness of $TiO_2$ thin films.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.446-450
• /
• 2013

TRISO coated particles with a ZrC barrier layer were fabricated by a fluidized-bed chemical vapor deposition (FBCVD) method for a use in a very high temperature gas-cooled reactor (VHTR). The ZrC layer was deposited by the reaction between $ZrCl_4$ and $CH_4$ gases at $1500^{\circ}C$ in an $Ar+H_2$ mixture gas. The amount of free carbon codeposited with in ZrC was changed by controlling the dilution gas ratio. Near-stoichiometric ZrC phase was also deposited when an impeller was employed to a $ZrCl_4$ vaporizer which effectively inhibited the agglomeration of $ZrCl_4$ powders during the deposition process. A near-stoichiometric ZrC coating layer had smooth surface while ZrC containing the free carbon had rough surface with tumulose structure. Surface roughness of ZrC increased further as the amount of free carbon increased.