• 한국전기전자재료학회논문지
• /
• 제29권6호
• /
• pp.370-375
• /
• 2016

In this paper, we investigated the electrical properties of crystalline silicon solar cell fabricated with Ni/Cu/Ag plating. The laser process was used to ablate silicon nitride layer as well as to form the selective emitter. Phosphoric acid layer was spin-coated to prevent damage caused by laser and formed selective emitter during laser process. As a result, the contact resistance was decreased by lower sheet resistance in electrode region. Low sheet resistance was obtained by increasing laser current, but efficiency and open circuit voltage were decreased by damage on the wafer surface. KOH treatment was used to remove the laser damage on the silicon surface prior to metalization of the front electrode by Ni/Cu/Ag plating. Ni and Cu were plated for each 4 minutes and 16 minutes and very thin layer of Ag with $1{\mu}m$ thickness was plated onto Ni/Cu electrode for 30 seconds to prevent oxidation of the electrode. The silicon solar cells with KOH treatment showed the 0.2% improved efficiency compared to those without treatment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.943-944
• /
• 2007

In this paper, the development and the test of 13.2kV/630A high-Tc superconducting fault current limiting coil are described. The fault current limiting coil made of Coated Conductor (CC) was fabricated with bifilar winding method for non-inductive characteristics and tested in the distribution power system level in Dec. 2006. In order to determine the length of the superconducting coil, applied voltage per unit length(V/m) was studied analytically and it was verified through experiments. For the volume minimization, the coil was designed with concentrical arrangement method. The short-circuit test was performed with the prospective fault current of asymmetrical 10kA whose maximum fault current was $30kA_{peak}$. In the test, the voltage drop and the current of the coil were measured and the resistance of the coil was obtained. Also, the temperature rise of the coil was calculated with the relationship between the resistance and the temperature of CC. In this paper, the experimental results are analyzed and compared with the simulation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.90.2-90.2
• /
• 2013

Vertically-aligned silicon nanostructure arrays (SNAs) have been drawing much attention due to their useful electrical properties, large surface area, and quantum confinement effect. SNAs are typically fabricated by chemical vapor deposition, reactive ion etching, or wet chemical etching. Recently, metal-assisted chemical etching process, which is relatively simple and cost-effective, in combination with nanosphere lithography was recently demonstrated for vertical SNA fabrication with controlled SNA diameters, lengths, and densities. However, this method exhibits limitations in terms of large-area preparation of unperiodic nanostructures and SNA geometry tuning independent of inter-structure separation. In this work, we introduced the layerby- layer deposition of polyelectrolytes for holding uniformly dispersed polystyrene beads as mask and demonstrated the fabrication of well-dispersed vertical SNAs with controlled geometric parameters on large substrates. Additionally, we present a new means of building in vitro neuronal networks using vertical nanowire arrays. Primary culture of rat hippocampal neurons were deposited on the bare and conducting polymer-coated SNAs and maintained for several weeks while their viability remains for several weeks. Combined with the recently-developed transfection method via nanowire internalization, the patterned vertical nanostructures will contribute to understanding how synaptic connectivity and site-specific perturbation will affect global neuronal network function in an extant in vitro neuronal circuit.

• 대한금속재료학회지
• /
• 제48권8호
• /
• pp.724-729
• /
• 2010

The effect of potassium permanganate ($KMnO_4$) in an electrolyte on the corrosion performance of magnesium alloy coated by micro-arc oxidation (MAO) has been investigated in this study. For this purpose, MAO coating was carried out on the present sample under AC condition in an alkaline silicate electrolyte with and without $KMnO_4$. Irrespective of the addition of $KMnO_4$, it was found from structural observation that the ceramic coating layers consisted of inner and outer layers. In the sample processed in the electrolyte with $KMnO_4$, the outer layer became dense and even contained a number of $Mn_2O_3$ atoms, resulting in high corrosion resistance. Based on the results of a potentiodynamic polarization test, it was confirmed that the coating layer formed in the electrolyte with $KMnO_4$exhibited better corrosion resistance than that without $KMnO_4$. The high corrosion resistance of the MAO-treated magnesium alloy was explained in relation to the equivalent circuit model.

• Journal of Ceramic Processing Research
• /
• 제13권spc2호
• /
• pp.308-311
• /
• 2012

A wide range of possible hazards existing in thermal batteries are mainly caused by thermal runaway, which results in overheating or explosion in extreme case. Battery separators ensure the separation between two electrodes and the retention of ion-conductive electrolytes. Thermal runaways in thermal batteries can be significantly reduced by the adoption of these separators. The high operating temperature and the violent reactivity in thermal batteries, however, have limited the introduction of conventional separators. As a substitute for separators, MgO powders have been mostly used as a binder to hold molten salt electrolyte. During recent decades the fabrication technology of ceramic fiber, which has excellent mechanical strength and chemical stability, has undergone significant improvement. In this study we adopted wet-laid nonwoven paper making method instead of the electrospinning method which is costly and troublesome to produce in volume. Polymeric precursor can readily be coated on the surface of wet-laid ceramic paper, and be formed into ceramic film after heat treatment. The mechanical strength and the thermo-chemical stability as well as the wetting behaviors of ceramic separators with various molten salts were investigated to be applicable to thermal batteries. Due to their excellent chemical, mechanical, and electrical properties, wet-laid nonwoven separators made from ceramic fibers have revealed positive possibility as new separators for thermal batteries which operate at high temperature with no conspicuous sign of a short circuit and corrosion.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.281-282
• /
• 2023

The solid-state reference electrodes made of polyaniline-coated MnO₂ (SSRE-PAM) and their electrochemical characteristics were studied in simulated concrete pore solutions (SCPS) containing 0 and 3.5% NaCl. Saturated calomel electrodes (SCE) have been used to conduct electrochemical studies on the stability behavior of SSRE-PAM. Open circuit potential (OCP) and potentiodynamic polarization techniques were used to assess the corrosion performance of steel rebar exposed in SCPS with 0 and 3.5% NaCl using SSRE-PAM. The results demonstrate that the SSRE-PAM was capable of identifying steel rebar in a concrete environment that was either passive or active. Potentiodynamic polarization parameters such as E_corr and I_corr for steel rebar in SCPS containing 0 and 3.5%)NaCl are greater than that of the passive condition (0% NaCl). All the studies validate the importance of using SSRE-PAM for corrosion monitoring applications in concrete structures.

• 태양에너지
• /
• 제10권3호
• /
• pp.60-65
• /
• 1990

[ $p^+$ ]형의 InP 기판($p=4{\times}10^{18}cm^{-3}$)에 일정 온도에서 S를 열 확산시켜 $n^+-p^+$ 접합을 형성하고, $n^+$형 측에 사진식각법으로 폭 $20{\mu}m$의 표면 격자상 전극을 $300{\mu}m$ 간격으로 형성한 후, 반사방지(AR) 막으로 $600{\AA}$ 두께의 SiO 박막을 증착시켜 크기 $5{\times}5{\times}0.3mm^3$의 $n^+-p^+$ InP 동종접합 태양전지를 제작하였다. S의 접합깊이는 약 $0.4{\mu}m$이었으며, 제작된 태양전지는 확산시간이 증가함에 따라 단락전류($J_{sc}$)가 증가하였고, 충진율(F.F)이 감소하였으며, 직렬저항($R_s$)과 에너지 변환효율(${\eta}$)이 증가하는 경향을 나타냈다. $5,000-9,000{\AA}$의 파장 영역에서 양호한 분광감도 특성을 나타냈으며, 단락전류, 개방전압($V_{oc}$), 충진율, 에너지 변환효율이 각각 $13.16mA/cm^2$, 0.38V, 53.74%, 10.1%인 태양전지를 제작하였다.

• 한국결정성장학회지
• /
• 제33권4호
• /
• pp.153-157
• /
• 2023

반도체 회로를 제조하기 위해서 에칭, 세척, 증착 등의 공정들이 반복적으로 진행된다. 따라서 이러한 공정이 진행되면 진공장비 내부는 부식성이 높은 가혹한 플라즈마 환경에 노출되게 된다. 따라서 반도체 공정 장비의 내부를 플라즈마 노출에 강한 재료를 사용하여 코팅층의 에칭과 오염 입자의 생성을 최소화하여야 한다. 본 연구에서는 고상합성법에 의해 합성된 옥시불화이트륨 (YOF)를 이용한 증착층의 플라즈마 식각 특성을 향상시키기 위하여 YOF 분말에 AlF₃ 분말을 혼합하여 플라즈마 스프레이 공정으로 Al 금속위에 증착시키고 그 특성을 분석하였다. AlF₃ 혼합비율의 증가에 따른 증착층의 결정구조, 미세구조 및 화학조성 변화를 조사하고 증착된 코팅층의 플라즈마 식각율을 측정하여 AlF₃ 혼합비율과의 상관관계를 분석하였다.

• 마이크로전자및패키징학회지
• /
• 제17권2호
• /
• pp.63-67
• /
• 2010

본 연구에서는 P3HT와 PCBM 물질을 전자도너와 억셉터 광활성층 물질로 사용하여 벌크이종접합 구조를 갖는 Glass/ITO/PEDOT:PSS/P3HT-PCBM/Al 구조의 유기박막태양전지를 제작하였다. P3HT와 PCBM은 각각 0.5 wt%의 농도로 톨루엔 용액에 용해하였다. 광활성층 농도를 최적화하기 위하여 P3HT:PCBM= 3:4, 4:4, 4:3 wt%의 농도비로 소자를 제작하고, 농도비에 따른 전기적 특성을 조사하였다. 또한 활성층의 후속열처리 온도가 소자의 전기적 특성에 미치는 영향을 조사하였다. P3HT와 PCBM의 농도비가 4:4 wt%의 비율에서 가장 우수한 전기적 특성을 나타내었으며, 이때 단락전류밀도 ($J_{SC}$), 개방전압 ($V_{OC}$), 및 충실인자 (FF)는 4.7 $mA/cm^2$, 0.48 V 및 43.1%를 각각 나타내었다. 또한 전력변환효율(PCE)은 0.97%의 값을 얻었다. 최적화된 농도비를 갖는 태양전지 소자에 대해 $150^{\circ}C$에서 5분, 10분, 15분, 20분간 후속 열처리를 실시한 결과 P3HT 전자도너의 흡광계수가 증가하는 경향을 보였다. 후속 열처리 조건이 $150^{\circ}C$에서 15분인 경우 전기적 특성이 열처리 하지 않은 소자에 비해 특성이 개선되었다. 즉, 이때의 전기적 특성은 $J_{SC},\;V_{OC}$, FF, PCE의 값이 각각 7.8 $mA/cm^2$, 0.55 V, 47%, 2.0%를 나타내었다.

• 멤브레인
• /
• 제30권1호
• /
• pp.38-45
• /
• 2020

리튬금속전지(LMB)는 매우 큰 이론 용량을 갖지만 단락(short circuit), 수명 감소 등을 야기하는 덴드라이트(dendrite)가 형성되는 큰 문제점을 갖고 있다. 본 연구에서는 poly(dimethylsiloxane) (PDMS)에 graphene oxide (GO) nanosheet를 고르게 분산시킨 PDMS/GO 복합체를 합성하였고 이를 박막 형태로 코팅하여 덴드라이트의 형성을 물리적으로 억제할 수 있는 막의 효과를 이끌어내었다. PDMS의 경우, 그 자체로는 이온 전도체가 아니기 때문에 리튬 이온의 통로를 형성시켜 리튬 이온의 이동을 원활하게 하기 위하여 5wt% 불산(HF)으로 에칭하여 PDMS/GO 박막이 이온전도성을 가질 수 있도록 하였다. 주사전자현미경(scanning electron microscopy, SEM)을 통해 전면 및 단면을 관찰하여 PDMS/GO 박막의 형상을 확인하였다. 그리고 PDMS/GO 박막을 리튬금속전지에 적용하여 실시한 배터리 테스트 결과, 100번째 사이클까지 쿨롱 효율(columbic efficiency)이 평균 87.4%로 유지되었고, 박막이 코팅되지 않은 구리 전극보다 과전압이 감소되었음을 전압 구배(voltage profile)를 통해 확인하였다.