• Elastomers and Composites
• /
• v.35 no.3
• /
• pp.173-179
• /
• 2000

Cure characteristics. tensile properties, and dynamic properties were investigated on the carbon black-filled natural rubber compounds, in which three typical vulcanization types conventional vulcanization(Conv), semi-efficient(Semi-EV), and efficient(EV) vulcanizations were used. The effects of vulcanization temperature on both the mechanical property and aging resistance of rubber compounds were also investigated. The Conv cure system showed a slightly slower rate of vulcanization than those of Semi-EV and EV ones. On the other hand, it showed a higher value in the maximum torque of cure curve. Higher tensile moduli were observed in Conv system than those in Semi-EV and EV ones, while lower elongation at break were obtained in Conv one. The tensile strength at break were found to be about the same for three cute systems. Hardness, modulus, and tensile strength decreased with increasing the vulcanization temperature, and the degree of changes in the properties was found to be smaller for EV and Semi-EV systems than that in Conv one. The EV system was found to be superior in thermal-aging resistance to Conv one.

• Journal of Technologic Dentistry
• /
• v.13 no.1
• /
• pp.27-31
• /
• 1991

The purpose of this study was to evaluate the effect of curing time and curing temperature on the hear - Curing of acrylic resin using ring furnace. Specimens were fabricated from 2 kinds(Laboron, Bertex) heat-cured resin. Total 200 samples were divided into 4 groups(70$^{\circ}C$, 100$^{\circ}C$, 13$^{\circ}C$, 150$^{\circ}C$) and each group was divided into 5 small groups(30 min., 45min., 60min., 75min., 90min.). A microscope(Olympus Coll Co. Japan) was used to examine a randomly selected central zone, midzone and surface for each complete specimen. The results of the experiment were as follows : 1. To obtain non-polymerzation, cure the resin for 30 minutes at 70$^{\circ}C$ and 100$^{\circ}C$ in a ring furnace. 2. To obtain with porosity, cure the resin for 45 minutes, 60 minutes and 75 mintes at 70$^{\circ}C$ and for 90 minutes at 150$^{\circ}C$ in ring furnace. Porosity appears in Laboron for 30 minutes, 45 minutes at 150$^{\circ}C$ in a ring furnace. 3. Every other specimens connot get a sight of special problem with makes eye in the made surface.

• Polymer(Korea)
• /
• v.36 no.2
• /
• pp.235-244
• /
• 2012

A thiazole type accelerator MBT (2-mercapto benzothiazole) was added into silica filled natural rubber (NR) compound with various concentrations (0, 1, 2, 3, 4 phr). The effects of MBT on the cure rate, mechanical property, degree of rubber-filler interaction (${\alpha}_F$), crosslinking density, and viscoelastic property ($tan{\delta}$) were investigated. As accelerator concentration increased, the $t_{s2}$ and $t_{90}$ decreased and the crosslinking density and modulus at 300% elongation increased. The tensile strength and elongation increased up to 3 phr and no further increased at 4 phr. The $tan{\delta}$ value measured at room temperature was higher than that of the $70^{\circ}C$. The ${\alpha}_F$ value was not affected by the addition of MBT. The mechanisms for the vulcanization rate were reviewed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.100-101
• /
• 2014

The global warming because of the CO₂ emission and solution about this emerge as the international enviroment problem. Particularly, it is the absolutely it is needed for reducing the CO₂ in the cement industry and harmful material actual condition. And the construction of home and abroad and material manufacturers tries for the technology development for the carbon dioxide and harmful material reduction which the portland cement in manufacture is usually emitted along with the increase of concerns about the environment-friendly concrete and panel. Therefore, in this research, the compressive strength of the inorganic binder and flexural strength tries to be measured in order to draw the inappropriate high temperature cure time of the ternary system inorganic binder using the blast furnace slag, red mud, silica fumewhich is the industrial byproduct with the cement substitute material, and etc.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.183-186
• /
• 2003

Long shafts for power transmission should transmit torsional load with vibrational stability. Hybrid shafts made of unidirectional fiber-reinforced composite and metal have high fundamental bending natural frequency as well as high torque transmission capability. However, thermal residual stresses due to the coefficient difference of thermal expansion of the composite and metal are developed so that the high residual stresses decrease fatigue resistance of the hybrid shafts, especially at low operating temperatures. In this work, axial compressive preload was given to the shaft in order to change the residual stresses. Static and fatigue torsional tests were performed and correlated with stress analyses with respect to the preload and service temperature.

• Elastomers and Composites
• /
• v.29 no.2
• /
• pp.121-130
• /
• 1994

The physical properties of rubber blend between natural rubber(NR) and ethylene propylene diene terpolymer(EPDM) were investigated as a study of EPDM composite materials. For EPDM/NR blends, the effects of ethylene and diene contents in EPDM, blend ratio, dicumyl peroxide(DCP) curing system on the physical properties, interfacial adhesion force and dynamic crack growth etc. were studied. EPDM/NR blends loaded with carbon black were prepared by mechanical mixing and cured by plate heating cure press. Crosslinking density was measured by swelling method with toluene. The physical properties of all blends were measured with Instron, fatigue to failure(FTF), Demattia flex cracking tester(DMFC), scanning electron microscopy (SEM), etc. As the ethylene and diene contents in EPDM increased, the physical properties, such as dynamic crack growth, adhesion to other component were increased too. Interfacial adhesion force of EPDM/NR blends to dissimilar layer was improved by the use of optimum peroxide curing system.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.406-410
• /
• 2014

Zinc ion containing thiuram type accelerator zinc dibutyldithiocarbamate (ZDBC) was compared to other thiuram type accelerators (tetramethylthiuram disulfide (TMTD) and dipentamethylenethiuram tetrasulfide (DPTT)) in silica filled natural rubber (NR) compound upon vulcanization and mechanical properties (modulus, tensile strength, and elongation %). ZDBC added compound showed the fastest cure time (t10) and the highest reinforcement index (R.I.) among them and showed a marching behavior. The mechanism was reviewed and a new mechanism was proposed.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.471-476
• /
• 2008

The thermal and mechanical properties and morphology of epoxy/polyamide/DDS/2E4MZ-CNS reactive blends with various amounts of polyamide were investigated. The amount of polyamide was 10, 20, and 30 phr and 2 phr of catalyst was added to the blend to cure at $180^{\circ}C$ for 30 min. By adding the catalyst, 2E4MZ-CNS, to the blend, the cure reaction occurred at a lower temperature. From the SEM images, it was found that the boundary of separated-phase was unclear and the phase was co-continuous. Without the catalyst, however, the boundary of separated-phase was clear. The control of cure temperature and morphology could be achieved by using a proper catalyst and consequently the mechanical strength increased by 20% compared to the blend without the catalyst due to the strong interaction between epoxy matrix and phase-separated polyamide at the interface.

• Restorative Dentistry and Endodontics
• /
• v.12 no.2
• /
• pp.45-53
• /
• 1987

The purpose of this study was to evaluate the tensile bond strength between composite resin and the human enamel. Three composite resin systems, two chemical (Clearfil Posterior, and Clearfil Posterior-3) and one light cure (Photo Clearfil-A), used with and without an intermediate resin (clearfil bonding agent), were evaluated under different amounts of load (10g, 200g and 200g for a moment) for in vitro tensile bond strength to acid-eched human enamel. Clinically intact buccal or lingual surfaces of 144 freshly extracted human permanent molars, embedded in acrylic were flattened with No #600 carborundum discs. Samples were randomly assigned to the different materials and treatments using a table of random numbers. Eight samples were thus prepared for each group(Table 2) these surfaces were etched with an acid etchant (Kurarey Co. Japan) in a mode of etching for 30 seconds, washing for 15 seconds, and drying for 30-seconds. During the polymerization of composite resin on the acid-etched enamel surfaces with and without bonding agent 10-gram, 200 gram and temporary 200 gram of load were applied. The specimens were stored in 50% relation humidity at $37^{\circ}C$ for 24 hours before testing. An universal Testing machine (Intesco model No. 2010, Tokyo, Japan) was used to apply tensile loads in the vertical directed (fig 5), and the force required for separation was recorded with a cross head speed of 0.25 mm/min and 20 kg in full scale. The results were as follow: 1. The tensile bond strength was much greater in applying a bonding agent than in not doing that. 2. The tensile bond strength of chemical cure composite resin was higher than that of light cure composite resin with applying on bonding agent on the acid-etched enamel. 3. In case of not applying a bonding agents on the acid-etching enamel, the highest tensile bond strength under 200 gram of load was measured in light cure composite resin. 4. The tensile bond strength under 200-gram of load has no relation with applying the bonding agent. 5. Under the load of 10-gram, There was significant difference in tensile bond strength as applying the bonding agent.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.8 no.3
• /
• pp.33-42
• /
• 2005

The bearing methods using pile of steel itself or reinforced concrete has been applying which in excavated depth was not deep. Also, the retaining wall as resisting structure to lateral force has taken weakness that the cure periods of concreted is long. Recently, with the material cost of steel, the application of cement is more increasing trend. In this study, the design methods of earth retaining and retention wall within the pre-casted concrete pile, PHC(Pretentioned spun High strength Concrete piles), was proposed which in the ground condition of excavated depth was not deep. The typical ground conditions, cohesive and non-cohesive soil, was considered as follows; soil strength as internal friction angle and UU(Undrained Unconsolidation triaxial test) strength, soil reaction and stabilization of structures. The application of design methods could be confirmed through the comparing and analyzing between measured data and utility software for the design.