• Korean Journal of Materials Research
• /
• v.17 no.7
• /
• pp.358-360
• /
• 2007

Cobalt subtitution on NiSi is investigated by using an ab-initio calculation. Firstly, a relaxed NiSi structure is calculated and the calculated lattice parameters are compared with experimentally determined lattice parameters. The calculated values are smaller than the experimental values by about 2%. As the calculation is based on 0 K, and the experimental measurement is performed at room temperature, those values are in good agreement. Next, a Co atom substitutes a Ni and Si site, respectively, to evaluate the preferable site between them. Co prefers Ni site to Si site. The calculated total energy also indicates that the Co substitution to Ni site stabilizes the NiSi structure. Therefore, the thermal stability of NiSi with Co addition can be achieved by the structure stabilization of NiSi by Co substitution into Ni site of NiSi.

• Journal of the Korean Magnetics Society
• /
• v.5 no.6
• /
• pp.963-967
• /
• 1995

Ultra thin layers of NiFeCo or NiFe were inserted at the interfaces of Ni and Cu to form a multilayer structure. In case of inserting a NiFe layer, the magnetoresistance was about 6%, the saturation magnetic field was 50 Oe and the hysteresis of R-H (resistance-magnetic field) was very small. In case of inserting a NiFeCo layer, the magnetoresistance increased to about 7% but the saturation magnetic field and hysteresis were also increased. The increase of the output under biased magnetic field was much larger in case of inserting a NiFe layer because of relatively smaller hysteresis in R-H behavior.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1998.10a
• /
• pp.20-21
• /
• 1998

• Journal of the Korean Magnetics Society
• /
• v.9 no.6
• /
• pp.296-300
• /
• 1999

Cross-shape structures of spin tunneling junctions were fabricated using DC magnetron sputtering and metal masks. The film structures were $substrate/Ta/NiFe/FeMn/NiFe/CoFe/Al_2O_3/CoFe/NiFe$ and $substrate/Ta/NiFe/CoFe/ Al_2O_3/CoFe/NiFe/FeMn/NiFe$. Fabrication conditions of insulating layer ($Al_2O_3$) and thickness and sputtering power of each film layer were varied, and maximum magnetoresistance ratio of 24.3 % was obtained. Magnetic characteristic variations in the above mentioned two structures and two types of substrates (Corning glass 7059 and Si(111)) were compared. Annealing of the junctions was performed to find out magnetic characteristic variations expected from the device fabrication. Magneoresistance Ratio were observed to maintain as-deposited value up to 150 $^{\circ}C$ annealing and then to drop rapidly after 180 $^{\circ}C$ annealing.

• Journal of the Korean Chemical Society
• /
• v.38 no.2
• /
• pp.136-145
• /
• 1994

Polymeric complexes such as M(Ⅱ)(PVPS)(SND), M(Ⅱ)(PVPS)(SOPD) have been prepared with monomeric complexes, M(Ⅱ)(SND) and M(Ⅱ)(SOPD)[M: Co(Ⅱ), Ni(Ⅱ), and Cu(Ⅱ)] and polymer PVPS. These complexes have been indentified by elemental analysis, spectroscopy, and T.G.A. From the results, it was found that M(Ⅱ)(PVPS)(SND), M(Ⅱ)(PVPS)(SOPD) complexes were penta-coordinated configuration. Electrochemical properties of these complexes studied by cyclic voltammetry and differential pulse polarography in 0.1 M TEAP-DMF solution at glassy carbon electrode. Co(Ⅱ)(PVPS)(SND) and Co(Ⅱ)(PVPS)(SOPD) showed irreversible two step reduction, such as Co(Ⅲ)/Co(Ⅱ) and Co(Ⅱ)/Co(Ⅰ), and Ni(Ⅱ)(PVPS)(SND), Ni(Ⅱ)(PVPS)(SOPD), Cu(Ⅱ)(PVPS)(SND), and Cu(Ⅱ)(PVPS)(SOPD) complexes showed irreversible one step reduction, such as Ni(Ⅱ)/Ni(Ⅰ) and Cu(Ⅱ)/Cu(Ⅰ), respectively.

• Journal of the Korean Magnetics Society
• /
• v.5 no.1
• /
• pp.15-20
• /
• 1995

We have prepared 20 kinds of Mn-Zn ferrites as content of CaO(0.1 mol%), NiO(0.0~0.60 mol%) and CoO(0.0~0.8 mol%) adding by the coprecipitation method and studied the magnetic properties as content of CaO, NiO and CoO adding. Initial permeability decrease as the content of NiO and CoO adding increases, while Curie tem~ perature increase as the content of NiO and CoO adding increases. $(H_{c})$, $(B_{s})$ and $(W_{h})$ increase as content of NiO adding increases.

• Journal of the Korean Magnetics Society
• /
• v.6 no.2
• /
• pp.112-116
• /
• 1996

스퍼터링법으로 제조한 NiFeCo/Cu/NiFeCo/FeMn 스핀밸브 자성 다층막의 자기적 성질과 자기저항에 대해 연구하였다. Cu 사잇층 두께가 15 .angs. 인 경우 약 6%의 자기저항을 얻을 수 있었다. NiFeCo/FeMn에서 교환이방성 자계는 약 20 Oe 정도였는데, 이는 NiFe/FeMn 계 스핀밸브 구조에서 보고된 값(100 Oe 이상) 보다 현저히 작은 것이다. 3 mTorr에서 제조한 NiFeCo 박막은 약 10 Oe 정도의 큰 보자력을 보임으로써 비슷한 조건에서 제조한 NiFe 박막의 경우(약 2 Oe)보다 상당히 큰 값을 갖는 것으로 관찰되었다. 작은 교환이방성 자계와 큰 보자력으로 인해 음 .rarw. 양 방향과 양 .rarw. 음 방향의 자화거동에 있어서 비대칭적인 자기저항 이력곡선 거동을 보이는 것으로 나타났다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.109-109
• /
• 2011

CO oxidaition reacitvity of bare and $TiO_2$ -coated NiO/$Ni(OH)_2$ nanoparticles was studied. For the deposition of $TiO_2$ atomic layer deposition was used, and formation of three-dimensional island of $TiO_2$ on NiO/$Ni(OH)_2$ could be identified. Based on the data of X-ray Photoelectron Spectroscopy, we suggest that only $Ni(OH)_2$ existed on the surface, whereas NiO disappeared upon $TiO_2$ deposition. Both CO adsorption and CO oxidation took place on NiO/$Ni(OH)_2$ surfaces under our experimental conditions. CO adsorption was completely suppressed after $TiO_2$ deposition, whereas CO oxidation activity was maintained to large extent. It is proposed that bare NiO can uptake CO under our experimental condition, whereas hydroxylated surface of NiO can be active for CO oxidation.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1069-1072
• /
• 2003

Germane-sillicide phase formation on S $i_{0.25}$G $e_{0.75}$ with Ni 100$\square$, Co 10$\square$/Ni 100$\square$ and Ni 50$\square$/Co 10$\square$/Ni 50$\square$ layer was studied by sheet resistance and Field Emission Scanning Electron Microscopy(FESEM). Thermal stability of nickel germane-silicide is found to be improved by sputtering Ni/Co/Ni on the SiGe. After annealing at 600, 650, $700^{\circ}C$, 30min., the nickel germane-silicide formed by Ni 50$\square$/Co 10$\square$/Ni 50$\square$ layer achieved a sheet resistance less than 17ohms/sq.(almost the same to the value before furnace annealing for 30min.) , while the process of the other two ways result in high sheet resistance and even sheet resistance fail due to Ge segregation.ion.

• International Journal of Advanced Culture Technology
• /
• v.3 no.2
• /
• pp.110-117
• /
• 2015

10 wt% (Ni-Co) catalysts with different Ni and Co content : 10%Ni, 9%Ni1%Co, 7%Ni3%Co, 5%Ni5%Co, 3%Ni7%Co, and 10%Co; were prepared using sol-gel method followed by incipient wetness impregnation method. To investigate the catalytic activity including the stability, dry methane reforming were demonstrated over the pelletized catalysts at $620^{\circ}C$ under atmospheric pressure in a $CH_4:CO_2:N_2$ feedstock for 360 min. The results showed that bimetallic catalysts with the Co content equal to or greater than 3% were more stable than monometallic catalysts (10%Ni and 10%Co). The temperature programmed hydrogenation interpreted that the additional of Co into Ni catalyst improved the carbon resistance from methane cracking. Promoted this type of bimetallic catalyst using 1wt% K (trimetallic catalyst) prevented the carbon formation on the catalyst. The temperature programmed desorption of $CO_2$ indicated that this trimetallic catalyst has a greater number of strong basic sites. Moreover, the appearance of K lowered the number of weak basic sites and decreased the conversion of methane by 12 %.