• 한국세라믹학회지
• /
• 제47권1호
• /
• pp.61-65
• /
• 2010

Ultrathin atomic layer deposition (ALD) coatings were found to enhance the performance of lithium-ion batteries (LIBs). Previous studies have demonstrated that $LiCoO_2$ cathode powders coated with metal oxides with thicknesses of $\sim100-1000{\AA}$ grown using wet chemical techniques improved LIB performance. In this study, $LiCoO_2$ powders were coated with conformal $Al_2O_3$ ALD films with thicknesses of only $\sim3-4{\AA}$ established using 2 ALD cycles. The coated $LiCoO_2$ powders exhibited a capacity retention of 89% after 120 charge-discharge cycles in the 3.3~4.5 V (vs. $Li/Li^+$) range. In contrast, the bare $LiCoO_2$ powders displayed only a 45% capacity retention. This dramatic improvement may result from the ultrathin $Al_2O_3$ ALD film acting to minimize Co dissolution or to reduce surface electrolyte reactions.

• 반도체디스플레이기술학회지
• /
• 제6권4호
• /
• pp.5-9
• /
• 2007

Phase transition and dopant redistribution during silicidation of $CoSi_2$ thin films were characterized depending on their preparation methods. Our results indicated that cleanness of the substrate surface played an important role in the formation of the final phase. This effect was found to be reduced by addition of W resulting in the formation of $CoSi_2$. However, even in this case, the formation of the final phase was achieved at the cost of extra thermal energy, which induced rough interface between the substrate and the silicide film. As for the dopant redistribution, the deposition sequence of Co and Si on SiGe was observed to induce significant differences in the dopant profiles. It was found that co-deposition of Co and Si resulted in the least redistribution of dopants thus maintaining the original dopant profile.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.276-279
• /
• 2004

The factors affecting Ni-Co alloy electroforming were investigated to determine the optimum bath composition and electroplating parameters, like pH, temperature, and current density, suitable for high speed fabrication of a micro mold with longer lifetime. To obtain alloy deposits having uniform thickness and composition, electroplating parameters were finely tuned with home-made electroforming apparatus. Ni-Co alloy deposits had linearly increased Co with $Co^{2+}$ ion concentration in electroplating bath, and showing $412H_v$ of Victors hardness at $23wt\%$ of Co content. For Ni-Co alloy, sulfonate and diol related organic additives were very effective to alleviate its residual stress and surface roughness. The maximum deposition rate was $106{\mu}m/hr$ at 10ASD and the tensile strength of alloy deposit was 2 times larger than that of Ni only case.

• Korean Chemical Engineering Research
• /
• 제47권1호
• /
• pp.11-16
• /
• 2009

단일벽 탄소나노튜브의 표면 위에 동력학적 전위법으로 산화루테늄($RuO_2$)의 석출 및 루테늄-코발트 혼합산화물(Ru-Co mixed oxide)의 공석출에 의해 산화환원 수퍼커페시터용 복합전극을 제조하였다. 루테늄 성분이 13.13 wt%, 코발트 성분이 2.89 wt%가 석출된 Ru-Co 혼합산화물 전극은 낮은 전위 스캔속도($10\;mV\;s^{-1}$)에서는 $RuO_2$ 전극과 유사한 비용량(${\sim}620\;F\;g^{-1}$)을 나타내지만, 높은 스캔속도($500\;mV\;s^{-1}$)에서는 $RuO_2$ 전극보다 큰 비용량을 보인다. 높은 스캔 속도에서 Ru-Co 혼합산화물 전극이 비용량의 증가를 나타내는 것은 Ru 성분을 통한 전기전도성을 Co 성분이 구조적으로 지지해주기 때문이다.

• 한국가스학회지
• /
• 제13권5호
• /
• pp.33-38
• /
• 2009

일산화탄소, 수소와 같은 친환경 연료용 가스를 이용하여 메탄화 반응을 거쳐 합성 가스를 생성하였다. 이를 위한 촉매로 상용 알루미나에 담지된 Ni-Co 이원 금속을 증착침전법을 사용하여 제조하였으며 제조된 촉매의 촉매 활성 비교를 위하여 Ni, Co 단일 금속 촉매를 동일한 방법으로 제조하였다. 제조한 촉매를 TEM, XRD, TPR 분석을 실시하여 각각의 촉매 특성을 확인하였고 메탄화 반응을 진행하여 합성 가스 전환율을 측정하였다. 증착침전법으로 제조한 촉매의 경우, 금속 입자가 작은 크기로 분산된 것을 확인하였다. Ni, Co 두 금속이 담지된 이원 촉매는 Ni, Co가 각각 담지된 단일 금속 촉매에 비해 더욱 높은 활성을 나타내었으며 TPR 분석 결과, 이는 두 금속의 공존으로 인한 상호 작용을 통해 활성 수소를 보다 증가시켰기 때문으로 나타났다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 제2회 학술대회 논문집 일렉트렛트 및 응용기술전문연구회
• /
• pp.59-63
• /
• 2000

BSCCO thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra-low growth rate, and sticking coefficients of the respective elements are evaluated. The sticking coefficient of Bi element exhibits a characteristic temperature dependence : almost a constant value of 0.49 below $730^{\circ}C$ and decreases linearly with temperature over $730^{\circ}C$ This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, $Bi_2O_3$, from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the Bi(2212) phase formation in the co-deposition process.

• 한국표면공학회지
• /
• 제24권1호
• /
• pp.8-8
• /
• 1991

To investigate the effects of substrate on transverse-rupture strength(TRS) and bonding strength between substrate and TiC layer coated by CVD, two kinds of substrate (substrate A:WC-9.5wt%Co-MC*[low C], substrate B: WC-6wt% Co-MC*[high C] were studied in terms of Cobalt and C contents respectively. For preparation of test samples the coating parameters of deposition time, deposition temperature and deposition pressure were varied. The result show that the carbon contents in substrates have greater effects on the TRS of the CVD TiC coated cemented carbide than Co contents in substrates.

• 한국표면공학회지
• /
• 제25권1호
• /
• pp.8-15
• /
• 1992

To investigate the effects of substrate on transverse-rupture strength(TRS) and bonding strength between substrate and TiC layer coated by CVD, two kinds of substrate (substrate A: WC-9.5wt% Co-MC＊[low C], substrate B: WC -6wt% Co-MC＊[high C]) were studied in terms of Cobalt and C contents respectively. For preparation of test samples the coating parameters of deposition time, deposition temperature and deposition pressure were varied. The results show that the carbon contents in substrates have greater effects on the TRS of the CVD TiC coated cemented carbide than Co contents in substrates. ＊MC:TiC+TaC

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 춘계학술대회 논문집
• /
• pp.94-97
• /
• 2005

Bismuth high Tc superconducting thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra low growth rate, and sticking processing of the respective elements are evaluated. The sticking processing of bismuth element in bismuth high Tc superconducting thin film formation was observed to show a unique temperature dependence; it was almost a constant value of 0.49 below about $730^{\circ}C$ and decreased linearly over about $730^{\circ}C$. This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, $Bi_2O_3$, from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the bismuth phase formation in the co-deposition process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.432-434
• /
• 2009

Metal nano-wire arrays on Cu-coated seed layers were fabricated by aqueous solution method using sulfate bath at room temperature. The seed layers were coated on Anodic aluminum oxide (AAO) bottom substrates by electrochemical deposition technique, length and diameter of metal nano-wires were dominated by controlling the deposition parameters, such as deposition potential and time, electrolyte temperature. Anodic aluminum oxide (AAO) was used as a template to prepare highly ordered Ni, Fe, Co and Cu multilayer magnetic nano-wire arrays. This template was fabricated with two-step anodizing method, using dissimilar solutions for Al anodizing. The pore of anodic aluminum oxide templates were perfectly hexagonal arranged pore domains. The ordered Ni, Fe, Co and Cu systems nano-wire arrays were characterized by Field Emission Scanning Electron Microscopy (FE-SEM) and Vibrating Sample Magnetometer (VSM). The ordered Ni, Fe, Co and Cu systems nano-wires had different preferred orientation. In addition, these nano-wires showed different magnetization properties under the electrodepositing conditions.