• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.2005-2010
• /
• 2004

Ultrasonic cleaning is performed by cavitation which is caused by the change of the sound pressure due to the vibration in a cleaning tank. In this study, experiments on electric power and sound pressure with various temperatures, dissolved oxygen and the level of the fluid was done in order to find out how the changes in a cleaning tank affect cavitation. As a result of a series of experiments, we found that transducer impedance changes periodically in response to the variances of fluid and have a direct influence on cleaning efficiency.

• Particle and aerosol research
• /
• v.9 no.3
• /
• pp.139-147
• /
• 2013

The performances of indoor air cleaners including particle cleaning capacity and collection efficiency are usually tested at the condition of the maximum air flow rate of the air cleaners. However, the power consumption of the air cleaners is highly dependent on the air flow rate of the individual air cleaners. Therefore, there seems to be an optimized air flow rate for the air cleaning capacity considering power consumption. In this study, clean air delivery rate(or standard useful area as suggested room size) and power consumption have been investigated for different maximum air flow rates of 15 air cleaners and then compared those for different air flow rate modes of the individual 5 air cleaners selected from the 15 cleaners. For the maximum air flow rate conditions of 15 air cleansers, the power consumption per unit area was less related to the maximum air flow rate. However, for the different air flow rate modes of the selected 5 air cleaners, the lower power consumption per unit area was corresponding to the lower air flow rate mode of the individual air cleaners. When considering the operation time to the desired particle concentrations, there was an optimized one in the medium air flow rate modes for the individual air cleaners. Therefore, not only the maximum air flow rate but also lower air flow rates of individual air cleaners should be considered for estimating air cleaning capacity based on energy consumption per unit area.

• Journal of Ocean Engineering and Technology
• /
• v.34 no.6
• /
• pp.377-386
• /
• 2020

This paper discusses the effectiveness of onboard measurements and data extracted from weather information for speed-power analysis. Furthermore, validation results of hull and propeller cleaning and painting during dry-docking are discussed. Wind and wave information can be obtained from onboard measurements or weather information from the National Oceanic and Atmospheric Administration (NOAA). The weather information of a specified position and time is extracted from NOAA weather data and compared with onboard measurements. In addition, to validate the effects of hull cleaning and painting during dry-docking, speed-power analysis results of before and after dry-docking are compared. The results show that both onboard measurements and weather information show acceptable reliability when added resistance and speed-power analysis results are compared with each other. Moreover, the ship performance analysis (SPA) software clearly shows the effects of hull cleaning and painting, and it can provide reliable analysis results with either onboard measurements or weather information. In conclusion, it is confirmed that the analysis method and SPA software used in this study are effective in analyzing the ship's speed-power performance.

• Journal of dental hygiene science
• /
• v.13 no.1
• /
• pp.83-90
• /
• 2013

The aim of this study was to evaluate the abrasive effect and cleaning power of toothpaste containing tetrasodium pyrophosphate and cellulose. The relative dentin abrasivity, cleaning power by modified Stookey method, dentin abrasivity of brushing after Cola treatment and consumer survey were investigated with control toothpaste containing dental type silica as an abrasive. The results obtained were as follows: 1. Experimental toothpaste hardly influenced dentin abrasivity, but control toothpaste had an effect on dentin abrasivity significantly (p<0.05). 2. There was no significant difference in cleaning power between experimental and control toothpaste (p>0.05). 3. Experimental toothpaste hardly influenced dentin abrasivity, despite 100 or 1,000 times of brushing after Cola treatment, but control toothpaste showed a big increase in dentin abrasivity as the number of brushing has been increased (p<0.05). 4. According to the consumer survey results, there was no difference between control and experimental toothpaste in the satisfaction rate of refreshing sensation, the satisfaction rate of the lasting effect of refreshing sensation and the overall satisfaction rate of the toothpaste (p>0.05). These results showed a possibility to make abrasive free toothpaste having cleaning power without dentin abrasivity.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.10a
• /
• pp.955-956
• /
• 2005

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.11
• /
• pp.971-975
• /
• 2013

In general, the solar photovoltaic power increases with higher solar insolation. However, the solar cell generation efficiency reduces because the solar cell surface is heated by solar insolation. According to advanced research, with a $1^{\circ}C$ increase in the solar cell surface temperature, the generation efficiency decreases by ~0.5%. To solve this problem, we conducted experiments in which we attempted to reduce the solar cell surface temperature using a water jet spray. In this study, we found the long-term experimental results of increases in solar power generation. The experimental results show a comparison of the site with and without cooling and cleaning equipment being installed. The results of the long-term experiments show that solar photovoltaic power generation is increased by at least 13% up to 19% with cooling and cleaning.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1090-1091
• /
• 2015

사막은 일조량이 많고, 세계적으로 넓은 규모를 가지고 있어 대규모 태양광 발전소 건설에 주목받고 있지만, 태양광 모듈 표면에 쌓이는 모래먼지로 인하여 발전효율 저하가 발생되고 있는 실정이다. 이에 태양광 모듈 표면의 모래먼지를 제거할 수 있는 태양광 모듈 크리닝 시스템을 개발 하였다. 본 논문에서는 사막 환경을 고려하여 물을 필요로 하지 않는 압축공기 및 회전하는 브러쉬로 모듈 표면을 세척하는 Solar Module Cleaning System을 제안한다.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.6
• /
• pp.587-594
• /
• 2016

This study aims to analyze the benefit-cost of the cleaning device for photovoltaic power generation systems in buildings in order to check its economic feasibility. A product, which has similar characteristics to the ultrasound-based cleaning device and is widely used in South Korea, was selected to compare with the benefit-cost value of the ultrasound-based cleaning device in this study. In order to quantitatively and qualitatively analyze benefit and cost aspects of the two products, categories and evaluation factors of each aspect as well as evaluation criteria were identified. Based on the identified evaluation factors and criteria, this study conducted face-to-face interviews with 15 experts to measure weights of benefit and cost aspects of the products. As the results, the total benefit weight of the ultrasound-based cleaning device was larger than its total cost weight since the benefit-cost value was greater than 1, which was 1.6 times of that of to compared product. Therefore, from the economic perspective, it is worth to develop the cleaning device for photovoltaic power generation systems applying ultrasound technology.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.2
• /
• pp.107-113
• /
• 2010

The object of this research is to conform of practicable possibility and recycling of producing junk after citrus fruits is processed. With extracting d-limonene oil that have 70~90% a component of oil out of junk citrus peel, making certain the about 12000ppm concentration of it. Limonene derived from citrus in jeju using conventional synthetic detergents can be replaced with the development of environmentally friendly natural detergent investigated the possibility. Mostly due to ocean dumping, disposal and cause environmental problems by recycling natural citrus cleaner alternative to the research conducted on the possibility. Cleaning efficiency with temperature did not affect the largest concentrations were able to identify the difference between cleaning efficiency. At least 10% of the d-limonene oil could be from the cleaning performance, increasing the concentration of the cleaning efficiency was increased in size. Ultrasonic is very high removal efficiency under the conditions shown in the cause of pure self-generated ultrasonic cleaning power as co-effects of d-limonene oil appears to chemical cleaning effect of ultrasonic cavitation occurs in the physical cleaning effect due to a combination of synergistic stability is maximized by low concentrations of d-limonene oil in a short time showed an excellent cleaning ability. Having the ability of cleaning at the same time, considering the side recycling in the junk citrus peels reflects possibility of basic materials utility eco-friendly in the skin soap, bath soap, cosmetics etc, through ability of exclusion a contaminant in based cleaning effect(EC) it can prospect substitution effect environmentally in the pre existence synthetic detergents.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.20 no.1
• /
• pp.1-6
• /
• 2024

Crud is a corrosion deposit that forms in equipments and piping of nuclear reactor's primary systems. When crud circulates through the reactor's primary system coolant and adheres to the surface of the nuclear fuel cladding tube, it can lead to the Axial Offset Anomaly (AOA) phenomenon. This occurrence is known to potentially reduce the output of a nuclear power plant or to necessitate an early shutdown. Consequently, worldwide nuclear power plants have employed ultrasonic cleaning methods since 2000 to mitigate crud deposition, ensuring stable operation and economic efficiency. This paper details the system configuration of ultrasonic nuclear fuel cleaning equipment, outlining the function of each component. The objective is to contribute to the local domestic production of ultrasonic nuclear fuel cleaning equipment. Additionally, the paper introduces a method for accurately measuring the weight of removed crud, a crucial factor in assessing cleaning effectiveness and providing input data for the BOA code used in core safety evaluations. Accurate measurement of highly radioactive filters containing crud is essential, and weighing them underwater is a common practice. However, the buoyancy effect during underwater weighing may lead to an overestimation of the collected crud's weight. To address this issue, the paper proposes a formula correcting for buoyancy errors, enhancing measurement accuracy. This improved weight measurement method, accounting for buoyancy effects in water, is expected to facilitate the quantitative assessment of filter weights generated during chemical decontamination and system operations in nuclear power plants.