• Journal of Hydrogen and New Energy
• /
• v.25 no.2
• /
• pp.145-150
• /
• 2014

This study investigates the preparation of anti-reflective (AR) coating film to improve the efficiency of solar cell. The AR coating film was successfully obtained by dip-coating with AR coatings prepared by sol-gel method. Fluoroalkylsilane was additionally introduced into the coatings to give the self-cleaning effect of AR coating film. We performed the abrasion test, pencil scratch hardness test and cross-cut test to identify the mechanical strength of AR coating film. As the results, the transmittance of AR coating films with 9.07, 18.13 and 27.20 of IPA/MTMS molar ratios were 93.1, 93.6 and 95.3%, respectively. The water contact angle and transmittance of AR coating film increased by the introduction of hydrophobicity. The prepared AR coating film shows the high level of abrasion, hardness and adhesion. The IPA/MTMS molar ratio of 27.20 and the withdrawing speed range of 0.20 ~ 0.28cm/sec are the optimal coating condition in terms of the transmittance and mechanical strength of AR coating film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.4
• /
• pp.215-217
• /
• 2016

For the improvement of the anti-pollution properties of porcelain electrical insulators, in this study, we have applied the functional film to the surface of insulator. The functional films were coated on the ceramic substrates which components were like the porcelain electrical insulator. The coating material was applied to ceramic substrate by spray coating method and then the film was cured at around $300^{\circ}C$ for 10 minutes with different gas ambient, such as $O_2$, $N_2$, and only vacuum. We have measured the contact angle of the coated surface, and obtained the lowest angle ($8.9^{\circ}$) and a strong hydrophilic property at vacuum condition. The anti-pollution properties were measured, revealing that as the contact angle decreased, the anti-pollution properties improved. The mechanical hardness and adhesion were both excellent regardless of the annealing ambient.

• Asian-Australasian Journal of Animal Sciences
• /
• v.29 no.4
• /
• pp.580-585
• /
• 2016

The objective of this study was to determine cow characteristics and farm management factors during the dry period associated with early postparturient intramammary infection (IMI) and subsequent clinical mastitis (CM). Data were collected three times: before drying off (P1), during the dry period (P2), and 5 to 14 days after calving (P3), using questionnaires and farm investigation. Milk samples were aseptically collected for bacterial identification at P1 and P3. Factors associated with IMI and CM were analyzed using multiple logistic regression models. The final model showed that IMI in early postpartum was significantly associated with full insertion of dry cow antibiotic, dry cows in barns with a combination of tie and free stalls, body condition score (BCS) in dry period and after calving, and milk yield before drying off. For IMI cows, factors significantly associated with clinical expression of mastitis were having daily barn cleaning, teat disinfected with alcohol before administration of dry cow therapy, BCS before drying off, milk yield before drying off, and days in milk at drying off. In conclusion, both cow and farm management factors are associated with the IMI rate and subsequent expression of clinical signs of mastitis in early postpartum cows.

• Journal of Biosystems Engineering
• /
• v.42 no.1
• /
• pp.12-22
• /
• 2017

Purpose: This aim of this study was to develop a pick-up type pulse crop harvester for harvesting cut and dried pulse crop. Methods: The pick-up type pulse crop harvester was designed and constructed. Its specifications and operating performance were investigated. Results: Compared with conventional bean harvesters, the pick-up type pulse crop harvester adopted seven rows of chains with tines to pick-up the cut and dried pulse crop on a flat or ridged field, two transverse threshing drums with steel wire teeth to reduce the threshing speed, and a tilt plate and plastic bucket elevator for conveying clean grain to reduce damage. The threshing speed and the oscillating frequency of the separating and cleaning parts according to crop type and condition could be varied easily to efficiently use engine power and to improve harvesting performance. The harvester showed forward speed ranges of 0 ~ 1.5 m/s during harvesting operation, and 0 ~ 2.5 m/s during road travelling. The pick-up width of the harvester was about 1 m. Conclusions: The pick-up type self-propelled 51.5 kW harvester was designed and constructed to harvest cut and dried pulse crop. The effective field capacity of the harvester was predicted as above 40 a/h.

• The Journal of Korean Physical Therapy
• /
• v.22 no.2
• /
• pp.31-38
• /
• 2010

Purpose: We investigated the relationship of depression and the ability to engage in activities of daily living in the elderly. Methods: Subjects (n = 182) were 60 years or older and who attended the Senior College of Gimhae Senior Welfare Center. We collected data via a questionnaire, through a Self- recording method and through individual interviews. We collected data on personal and general characteristics, level of depression, and activities of daily living. Results: Among all subjects, 51.1% reported having depressionMild depression was reported by 29.7% (54 subjects), moderate depression by 13.2% (24 subjects), and severe depression by 8.2% (15 subjects). Activities of daily living, including walking, climbing stairs, standing from a chair and sitting on and using toilets, using a telephone, bathing, shopping, cleaning house, and managing money were significantly lower in elderly subjects who were depressed (p<0.05). The greater the level of depression, the less able they were to engage in activities of daily living. Conclusion: These findings may help us achieve early detection of depression in the elderly and provide mediated arbitration so that they can have better health condition and greater ability to engage in activities of daily living.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.167-175
• /
• 2000

An experimental research to evaluate the slip coefficient of high-strength slip-critical-type bolt connection of weathering steel plate has been performed in this paper. Experiments were performed with several surface conditions such as clean mill scale with hand or power brush cleaning, shot blast cleaned, inorganic zinc primer coated, and weather coated surfaces. Also, the relaxation of bolt clamping force was estimated during 500 hours. It was ascertained from the experiments that slip coefficients are greater than 0.40 in all faying surface conditions except mill scale surface with power brushing. The quantify of relaxation depended on the surface conditions and was $3{\sim}8%$, i.e., less than 10%.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.4 s.193
• /
• pp.153-158
• /
• 2007

Recently nano imprint lithography to fabricate photonic crystal on polymer is preferred because of its simplicity and short process time and ease of precise manufacturing. But, the technique requires the precise mold as an imprinting tool for good replication. These molds are made of the silicon, nickel and quartz. But this is not desirable due to complex fabrication process, high cost. So, we describe a simple, precise and low cost method of fabricating PDMS stamp to make the photonic crystals. In order to fabricate the PDMS mold, we make the original pattern with designed hole array by finding the optimal electron beam writing condition. And then, we have tried to fabricate PDMS mold by the replica molding with ultrasonic vibration and pressure system. We have used the cleaning process to solve the detaching problem on the interface. Using these methods, we acquired the PDMS mold for photonic crystals with characteristics of a good replication. And the accuracy of replication shows below 1% in 440nm at diameter and in 610nm at lattice constant by dimensional analysis by SEM and AFM.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.37 no.5
• /
• pp.667-675
• /
• 2013

After analyzing excavated $17-18^{th}$ century silk fibers through a scanning electron microscopy, we discovered seven different kinds of fracture morphology. Using Morton & Hearle fiber fracture morphology, we classified the findings into four different categories. Type I is tensile failure resulting from brittle fracture, granular fracture, and ductile fracture. Type II is fatigue failure caused by tensile fatigue, flex fatigue, and axial split (fibrillation). Type III is bacterial deterioration discovered only in excavated artifacts. Type IV is a combination of the three above. Humid underground conditions and the infiltration of bacteria caused the fibers to swell and weaken its interfibrillar cohesion. Fractures occur when drying and processing an excavated artifact that is already in a fragile condition. Therefore, one must minimize damage through a prompt cleaning process and make sure that the least possible force is exerted on the fabric during any treatment for repair and exhibition.

• Textile Coloration and Finishing
• /
• v.10 no.1
• /
• pp.11-19
• /
• 1998

For the purpose of standardization and practicability of dyeing by natural dyes, the mordanting and dyeing properties of cochineal and carminic acid were studied. Appropriate extraction, dyeing and mordanting condition of cochineal were determined, and the effect of mordanting method on dye uptake and color fastness of dyed fabric was investigated. The maximum absorbance of cochineal solution was 495nm, carminic acid was 533nm and 577nm. The color of carminic acid solution was affected by pH 6~9. The optimum temperature to extract cochineal was $80-100^\circ{C}$ and dyeing solution for 1 hour. And effective dyeing time to silk was 60min. Effective mordanting temperature was $80^\circ{C}$, and its time was 30min. In case mordants concentration, the maximum absorbance of Sn solution was 3%, K, Cu and Cr were in 1%. K/S value of dyeing fabrics was recoginazed by mordant treatment, specially Fe, Sn, Al, Cu. In the case of cochineal light fastness was increased by mordant treatment, specially Fe treatment. Perspiration fastness was good in acidic solution than in alkaline solution and perspiration fastness of cochineal was poor. Fastness of abrasion and dry-cleaning were good and these fastness improvement were generally effective for post-mordanting treatment.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.3
• /
• pp.209-214
• /
• 1999

This paper deals with the effects of activation process of MgO thin film on the dielectric characteristics of surface discharge type AC PDP. The discharge voltage decreased with increase in the MgO activation time and temperature until $400^{\circ}C$ under the condition of clean high vacuum. However, for the sample activated above $430^{\circ}C$ the discharge voltage increased. These results may be explained by the MgO morphology change and surface cleaning in the process of activation.