• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.4 s.193
• /
• pp.153-158
• /
• 2007

Recently nano imprint lithography to fabricate photonic crystal on polymer is preferred because of its simplicity and short process time and ease of precise manufacturing. But, the technique requires the precise mold as an imprinting tool for good replication. These molds are made of the silicon, nickel and quartz. But this is not desirable due to complex fabrication process, high cost. So, we describe a simple, precise and low cost method of fabricating PDMS stamp to make the photonic crystals. In order to fabricate the PDMS mold, we make the original pattern with designed hole array by finding the optimal electron beam writing condition. And then, we have tried to fabricate PDMS mold by the replica molding with ultrasonic vibration and pressure system. We have used the cleaning process to solve the detaching problem on the interface. Using these methods, we acquired the PDMS mold for photonic crystals with characteristics of a good replication. And the accuracy of replication shows below 1% in 440nm at diameter and in 610nm at lattice constant by dimensional analysis by SEM and AFM.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.30 no.4
• /
• pp.324-328
• /
• 2014

Aberrant anatomy of mandibular premolars is very rare in Korean, but aberration can contribute the endodontic failure as it makes difficult to remove the irritants during cleaning and shaping procedure. This case report describes the successful root canal treatment of a rare mandibular first premolar with C-shaped root canal as using a cone-beam computed tomography to understand the internal shape of root canal system and a dental operating microscope to improve the magnification and illumination.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.2
• /
• pp.107-115
• /
• 2003

Dairy manure amended with crop and forest residues (moisture 69% wet basis, C/N 22) was composted in a 605 L pilot-scale vessel using continuous air flow (56 L/min) for 19 days. Three pilot-scale sawdust biofilters (moisture 63%, pH 5.0) were built to clean biological waste gas from the composting process. For each methods, two replicated experiments were monitored over a period of three weeks. The system was evaluated to determine the biofilter media depth that would be adequate for compost odour reduction. The compost air cleaning was measured based on ammonia gas concentration before and after passing through the biofilter. Ammonia gas removal efficiency over 3 weeks was 42, 75 and 87% at sawdust biofilter media depth levels of 202, 400 and 600 mm, respectively. Each sawdust biofilter was operated at a moisture content in the range of 60~62% (wb), a temperature from 15 to $25^{\circ}C$, an average pressure drop from 240 to 340 Pa and a detention time from 60 to 180 seconds during the biofiltration process.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1996.06a
• /
• pp.149-153
• /
• 1996

반도체 소자 제조 공정이 고 집적화 됨에 따라 습식 세정방법에 의한 세정공정의 중요성이 더욱 증가 되어지고 있으며, 특히 그 중에서 전체 세정공정의 약 절반을 차지하고 있는 Deionised water에 의한 rinsing 공정의 경우 ultrapure water의 quality가 최근 지속적으로 향상이 되어짐에 따라 많은 발전을 자져 왔다. 일반적으로 Deionised water에 함유하고 있는 TOC(total oxidisable components), bacteria, metallic impurity, desolved oxygen cencentration, colloidal material impurity (예를 들면 Silica, oraganic substrate)등은 ultra pure water의 quality를 결정하는데 매우 중요한 factor로 작용하고 있으며, 이러한 불순물들이 반도체 제조공정중 wafer surface에 흡착되어 졌을때 여러형태의 defect들을 유발한다고 알려져 있다. 그러나 pseudommonas, flavobacterlum, alcaligene등의 기 얄려진 bacteria들의 경우 Deionised water를 supply해주는 배관의 Inner surface에 잘 흡착 되지만 고온의 water 혹은 과산화수소수($H_{2}O_{2}$) 를 이용하여 주기적으로 처리 해줌으로 인하여 이에 대한 문제점을 어느정도 최소화 시킬수 있다. 위의 두가지 방법중 전자의 경우 chemical을 사용하지 않고, 유지 및 관리가 간편하며, 용존산소량을 줄일수 있다는 점에서 장점이 있으나, 전 ultra pure water의 system이 열적으로 안정해야 하고 경제적인 문제가 수반하는 단점을 가지고 있다. 후자의 경우, 미량의 과산화수소수 (1~10,000 ppm)를 이용해 처리 해주는 방법의 경우 경제적으로 큰 장점이 있고, 처리가 단순하다는 장점이 있으나 과산화수소수 자체에 포함하고 있는 높은 impurit level, 그리고 처리후 장시간의 flushing time을 가져야 한다는 단점등이 존재 하고 있다.

• Membrane Journal
• /
• v.14 no.1
• /
• pp.66-74
• /
• 2004

Total resistance of membrane in a micro-filtration system using a metal membrane was mainly attributed to the permeate resistance of cake layer($R_c$), which was formed by deposited particles from the physico-chemical interactions of solids on membrane surface. Intermittent back ozonation was highly effective than the air backwashing for fouling reduction. As far the operational effect, under same ozone injection, the increase of gas flow-rate was more favorable than the increase of injection time far the recovery of permeation flux. As the filtration time was longer, the effect of flux recovery by intermittent back-ozonation decreased. Therefore, it is preferable to operate membrane cleaning before the foulant is consolidated on membrane surface.

• Journal of Environmental Science International
• /
• v.15 no.10
• /
• pp.913-918
• /
• 2006

Despite the wide distribution of air pollutants, the concentrations of indoor air pollutants may be the dominant risk factor in personal exposure due to the fact that most people spend an average of 80% of their time in enclosed buildings. Researches for improvement of indoor air quality have been developed such as installation of air cleaning device, ventilation system, titanium dioxide$(TiO_2)$ coating and so on. However, it is difficult to evaluate the magnitude of improvement of indoor air quality in field study because indoor air quality can be affected by source generation, outdoor air level, ventilation, decay by reaction, temperature, humidity, mixing condition and so on. In this study, evaluation of reduction of formaldehyde and nitrogen dioxide emission rate in indoor environments by $TiO_2$ coating material was carried out using mass balance model in indoor environment. we proposed the evaluation method of magnitude of improvement in indoor air quality, considering outdoor level and ventilation. Since simple indoor concentration measurements could not properly evaluate the indoor air quality, outdoor level and ventilation should be considered when evaluate the indoor net quality.

• KIEAE Journal
• /
• v.10 no.6
• /
• pp.105-114
• /
• 2010

As children are known to touch and chew everything, green cleaning procedures are an important step in preventing children from ingesting harmful toxins. The objectives of this study are to develop a new, self-evaluation checklist and to suggest design recommendations which comply with easy, adaptable, economical ways to improve the eco-friendly indoor environment of Korean childcare facilities. The information compiled during this study was collected through literature review and internet surveys1) from July, 2009 to February, 2010. The results of this study show that the current Korean childcare accreditation system and practices emphasize clean building interiors, policies for sanitation and cleanliness, and control of humidity and lighting. On the other hand, the information provided by green-building rating systems from GBCC, LEED, and GBTool offers additional and comparative details regarding indoor environment quality and standards regarding the IAQ performance and management plan, ventilation and thermal comfort systems, views from windows, acoustics, and lighting. In conclusion, this document provides an appropriate and easy-to-follow, self-evaluation checklist composed of eight criteria and 51 practical items. This study also provides the design recommendations composed of 27 practical ideas focusing on interior elements. Both the checklist and design recommendations I have suggested can be a post-occupancy tool for evaluating eco-healthy facility standards as well as tips for continuing to maintain eco-healthy childcare facilities.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.4
• /
• pp.548-552
• /
• 2010

The air suction filter of the power plant decrease the dust and impurities of suction air that reduce the life and efficiency of the boiler. The suction efficiency of the air filter falls with the dust and impurities when the time of use comes to be long. Therefore, the various contaminant of the filter must remove periodically. This paper presents a developed quick exhaust valve to use in the thermo-electric power plant. to removing contaminants on the filter, the blowing is done shortly by air pressure. The Air flowed out to the out side from the inside of the filter. The performance test of the developed valve is done by making a test-bench according to JIS and KS standards. The efficiency is found higher than the existing related valve.

• Journal of Families and Better Life
• /
• v.20 no.6
• /
• pp.219-227
• /
• 2002

This study was conducted to examine housing preferences among single-person households and to propose guidelines for housing design choices for single people. One hundred and sixty responses to the questionnaire developed by this researcher were analyzed utilizing frequencies, percentages, and t-tests. There were significant differences between single households and non-single households in various aspects of housing preferences. Differences were found in the desired type and size of housing, needed amount of space, and the importance of space itself. Single persons wanted to live in a small apartment, about 83.45$m^2$ (25.29 pyung) size. They consider the bathroom and the master bedroom more important than the living room and kitchen. They prefer to have specifically function-oriented rooms such as shower, home office, computer room, exercise room, or leisure space. Single persons consider information-technological facilities within an apartment very important. They would like to adopt automatic and electronic technology in the house, such as optical communication network, automatic air-cleaning system, and internet TV. Housing preferences differ significantly according to socio-demographic variables such as gender and age. I propose in this study a small-sized, information-, high-tech- and leisure-oriented design that corresponds with the actual housing preferences of the single-person households.

• IE interfaces
• /
• v.18 no.2
• /
• pp.136-147
• /
• 2005

This paper introduces a simulation study regarding the operation of the Painted Body Storage (PBS) in an automobile factory. In the paint shop of the factory, same colored bodies are grouped together in order to increase the effectiveness of process, for example decrease the loss of cleaning the painting-gun when the color of body changes from one to another. However the production of automobiles in the assembly shop is a typical example of the mixed model assembly production. Therefore PBS locates between the paint shop and the assembly shop for control the input sequence of bodies to the assembly shop, and it enables to meet the smoothing requirement of assembly sequence. There are highly restricted constraints on the assembly sequence in a assembly shop. Those are spacing restriction and smoothing restriction. If such restrictions are violated, conveyor-stop or utility work will be necessary. Thus the major objective of PBS is to control the assembly sequence in a way to meet the two restrictions. In this paper a case study of PBS in an automotive factory is introduced. The storage/retrieval algorithms are suggested and the proposed system is verified using simulation models. Sensitivity analysis for operating factors is also conducted.