• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.2 s.120
• /
• pp.25-30
• /
• 2007

Recently the use of web offset printing has been increasing, which can provide high print speed, mass production, and high print quality. However, high speed web offset printing has frequently undergone a blistering problem when the printed paper passes through hot air dryers. Blistering occurs in the middle of the base paper or in the coating layer. This paper focused on the blistering occurring in the base paper. In order to elucidate the effect of pigment ratio on blistering, 6 types of coating color were prepared with varying GCC/clay ratios and printability and blistering were investigated focusing on structure changes in the coating layer. When the clay content in the coating layer was increased, surface roughness and surface strength were decreased and paper gloss was increased. In addition, it was found that the coating layer structure with high clay content, which contains lots of discontinuous pores, hindered water vapors to penetrate out and, as a result, blistering occurred.

• Journal of Conservation Science
• /
• v.32 no.1
• /
• pp.75-88
• /
• 2016

In this study, 5 mural paintings in the Buddhist temples of Joseon era were researched for component analysis on the soil contained in the walls. The results of particle size analysis showed that the ratio of particle contents were different in each layer. In the finishing layer, the distribution of the middle sand fraction is higher than that of the middle layer. The results of XRD analysis showed that quartz, feldspar, and clay mineral are the main components of sand, suggesting similar mineral composition to that of ordinary soil component. It seems weathered rocks were used for construction of the walls. The main chemical components detected from EDX analysis were Si, Al, Fe, and K. Also the SEM images showed sand or clay sized minerals. In conclusion, the walls of the buddhist mural paintings in Joseon Dynasty had been constructed by using the loess, and had been produced by using mixture of clay and sand particles of different sizes for each layer. This study identified the characteristics of the materials and the manufacturing technologies used on the walls of mural paintings of Buddhist temples in Joseon era.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.3
• /
• pp.153-163
• /
• 2020

Mineral and geochemical analysis were conducted on two sections (~3.5 m) of red-brown claysilt sediments covering the gneiss and granite weathering zones in Suwon-si for establishing Quaternary paleoenvironmental changes in Korea. The sections were divided into four sedimentary layers (Unit 1-4) by vertical changes in mineral composition and chemical composition. The lowermost unit 1 was a sandy sediment with a high K-feldspar content with a significant contribution of weathered bedrock. Unit 2 was a transition layer showing intermediate characteristics. Unit 3 was a reddish brown clay-silt sediment, with a total clay content of 58% on average, and the main clay minerals were illite-smectite mixed layer minerals and hydroxy-interlayered vermiculite/smectite. Unit 3 contained almost no plagioclase, while the content of kaolin minerals derived by the plagioclase weathering was higher than in the other layers. Unit 4 had similar mineral composition and chemical properties to Unit 3, but had a higher content of plagioclase and chlorite and lower content of kaolin minerals. The chemical compositions of the sections were compared with those in other regions of Korea, suggesting the eolian origin of Units 3 and 4. The paleoenvironmental change in the sedimentary section of this region was interpreted as follows. Weathered products of gneiss and granite, which are bedrocks of this region, were eroded and deposited as sandy sediments in the periphery to form the lower layers (Unit 1, 2), followed by the deposition of the claysilty rich eolian sediments (Unit 3) during the glacial. Unit 3 was chemically weathered during the warm humid climate during the last interglacial, developing a reddish brown color. After that, a eolian sediment layer (Unit 4) was deposited during the last glacial.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.5
• /
• pp.5-13
• /
• 2017

The sand layer deposited in clay is called a sand seam, which is formed by inflow of sands due to river flooding or slope failure in the middle of sinking and sediment of clay. When the sand seam exists in clay layer, the drainage direction changes from one way to both ways, and the time of consolidation may be reduced. However, it is not clearly proved due to lack of studies of sand seam and currently is not reflected in the design of soft soil improvement. As a fundamental study about sand seam, the oedometer tests and constant rate of strain tests with Rowe cell were conducted on clay specimens with sand seam. For tests, a frozen method was specially designed for making the sand seam. It was concluded that the test results showed the sand seam affects the coefficient of consolidation of clay. If the thickness of sand seam exceeds 0.05 times of specimen height, the sand seam works as drainage layer of pore water horizontally as well as vertically, and consequently the consolidation is accelerated.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.28-35
• /
• 2004

Driven pile has the excellent bearing characteristics and good economics, so it is known as the comparative piling method. To use the advantages of driven pile fully, it is necessary to perform the proper construction management. Engineers must drive pile to the proper bearing layer with proper blow energy and measure the blow count and penetration per certain depth to analyze the bearing capacity and driveability. In conventional method, these parameters have been measured manually so it was difficult to get good accuracy. After PIR-D(Pile Installation Recorder-Driven Pile) was attached to the driving equipment, the hammer efficiency, blow count and penetration in blow/10cm were measured automatically. In this paper, to givethe rational judgement criteria of bearing layer, driveability, blow/10cm according to pile depth during pile driving, the some relationship between the driving resistance and ground layer distribution was analyzed. The ground investigation during piles (PHC ${\Phi}450,\;{\Phi}400\;&\;Steel\;Pile\;{\Phi}609{\ast}16t$) installation in the marine clay layer in Incheon, the sandy soil layer in Yongin and the tuff layer in Pusan was done. And measuring hammer efficiency not doing recently, we could compare hammer efficiency(Eh) by PIR-D and energy transfer ratio(ETR) by Pile Dynamic Analyzer(PDA).

• Journal of Environmental Science International
• /
• v.9 no.2
• /
• pp.125-129
• /
• 2000

As one of the fundamental survey to evaluate purification capacity of pollutants at the tidal flat sediments, we studied vertical environmental characteristics in three tidal flat sediments, Chunjangdae, Eueunri and Gyewhado. These are dissmilar to external feature in each other. The results of this study may be summarized as followed; As the results of particle analysis, Eueunri tidal flat fediment located in Keum river estuary consists of 98.98% as silt & clay, Chunjangdae tidal flat sediment located in SeocheonGun consists of 97.99% as sand. And Gyewhado tidal flat sediment located in Saemankeum in Saemankeum area consists area consists of 32.81% as silt & clay and 67.19% as sand. The concentration of organic pollutants(I.L., COD, POC, PON) in Eueunri tidal flat sediment which highly content of silt & clay were 3~4 times higher than others. The concentration of organic pollutants at each layer were slightly increase goes with deepen layer. The linear correlation between I.L. and COD, POC, PON were obtained. Correlation coefficients were in range of 0.821~0.940. Also the correlation between pH and COD, POC, PON were high(>r=0.9). Filteration rate in Chunjangdae tidal flat sediment was 0.01584cm/s as mean value, but the other were almost nothing filtered off.

• 보존과학연구
• /
• s.14
• /
• pp.77-93
• /
• 1993

In order to study for the production techniques and the materials of using in Korean Lacquer Antiques, we examined the section structure by SEM and Microscope, the qualitative analysis of lacquer layer by XRF and XRD, the qualitative analysis of Golhae layer by XRF and XRD, the qualitative analysis of Golhae by EDS on the locquer-wares which was excavated from Anapchi Pond Site in Kyungju and Miruksa Temple Site in Iksan. In the lacquer-wares excavated from Anapchi Pond Site, the lacuqer-wares layers made by a cloth attached on the surface of wooden vessel and Golhae-a mixture of clay and lacquer-covered on the cloth and finally finished with the red lacqure, being mixed with pure mercury sulfide(HgS) and lacquer. And raw materials of Golhae made of clay. The lacquer-wares excavated from Miruksa Temple Site in Iksan, we presumed that the lacquer-wares used fine born grains in place of clay for the raw materials of Golhae. Expecially in case of black lacquer-tray, we found that lacquer put on the surface of wooden vessel without cloth attaching and Golhae covering and the production of wooden vessel was used power-driven machine.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1991.10a
• /
• pp.62-74
• /
• 1991

The stability of the Carsington dam at Derbyshire in middle Eng1and is analysed using the Kinematical Element Method (Program LSDKSLOP). The thin yellow clay layer and the pore pressure at the failure surface, which goes through the core and boot, are considered. The influence of the pre-existing shears of the yellow clay on the stability of the Carsington dam is studied. Comparisons with the calculated and the observed failure surface are presented.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.25-32
• /
• 2000

In order to analyze the behavior of piled abutment adjacent to surcharge loads a numerical study was conducted. In 2D plane stalin analysis, the distribution of lateral soil movement was investigated by varying the thickness of clay layer and the magnitude of surcharge loads. In 3D analysis, the magnitude and distribution of lateral pile-soil movement were studied for different cap rigidity. Based on limited parametric studies, a simple method is proposed to identify the lateral pressure of piled abutment adjacent to surcharge loads.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.319-326
• /
• 2002

During the construction period of submarine shield tunnel, which is built firstly in very soft marine clay layer 40m deep in Korea, wide range problems were encountered such as safe launching against high earth pressure at shield entrance, technique of shield face pressure control when passing through complex multi-layered soils This paper introduces successful construction practice through development of state-of-the-art construction method and field monitoring.