• 한국농공학회논문집
• /
• 제59권5호
• /
• pp.73-81
• /
• 2017

The improved movable weir supplements the advantages and disadvantages of the rubber weir and the conduction gate. It consists of a stainless steel gate, air bags, and a steel clamping plate. The stainless steel gate is the main body of the weir, and the inflatable rubber sheet serves to support the steel gate. The steel clamping plate is typically in direct continuous contact with water, but this leads to corrosion issues that can reduce the life of the entire movable weir. In this study, a panel-type glass-fiber-reinforced polymer (GFRP) clamping plate was designed and fabricated. The test results showed that the flexural load of the panel-type GFRP composite clamping plate was over twice that of the wings type GFRP clamping plate. The lowest moisture absorption value was obtained upon exposure to tap water, and exposure to other solutions showed similar values. Additionally, flexural load testing after exposure to an accelerated environment found the lowest residual loads of 80.51 % and 78.50 % at 50 and 100 days, respectively, for exposure to a $CaCl_2$ solution, while exposure to other environments showed residual failure loads of over 80 % at both 50 and 100 days.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1350-1353
• /
• 2007

An experimental method based on contact resonance is developed to extract the contact parameters of mechanical joints under various clamped conditions. Mechanical joint parameters of shear contact stiffness and damping were extracted for different physical joint parameters such as surface finish of the mating surfaces, the presence of lubrication, the effect of the clamping pressure, and shear load. It was found that the shear contact stiffness values decreased with increasing clamping load and increased with increasing shear loading. Contact damping ratio values were almost constant with clamping load, but decreased with increasing shear load. Moreover, rough surfaces exhibited the highest shear stiffness and contact damping compared to smooth surfaces.

• Composites Research
• /
• 제18권5호
• /
• pp.9-14
• /
• 2005

복합재 구조물에서 체결부위는 매우 취약한 부분이므로 복합재료 체결부에 대한 설계는 중요한 연구분야로 대두되고 있다. 본 논문에서는 클램핑 포스가 존재하는 복합재료 기계적 체결부의 파손강도를 파괴면적지수법으로 예측하였다. 클램핑 포스가 존재하는 기계적 체결부의 파손강도를 파괴면적지수법으로 예측한 결과, $22.5\%$ 범위 내에서 체결부의 강도를 예측할 수 있었다.

• 드라이브 ㆍ 컨트롤
• /
• 제11권2호
• /
• pp.9-15
• /
• 2014

This paper deals with the issue of force synchronizing control for the clamping servomechanism of injection molding machines. Prior to the controller design, a virtual design model has been developed for the clamping mechanism with hydraulic systems. Then, a synchronizing controller is designed and combined with an adaptive feedforward control in order to accommodate the mismatches between the real plant and the linear model plant used. As a disturbance, the leakage due to the ring gap with relative motion in the cylinder has been introduced. From the robust force tracking simulations, it is shown that a significant reduction in the force synchronizing error is achieved through the use of a proposed control scheme.

• 한국생산제조학회지
• /
• 제6권3호
• /
• pp.26-35
• /
• 1997

In this study, the drawing characteristics of circular drawbead are examined with the plane strain elastic-plastic FE Method. Both the clamping load and the drawing load investigated by varying the process variables such as drawbead radius, closing depth and friction condition. The effective strain induced by the draw bead is also investigated. In order to verify the results, the computed results are compared with the existing experimental results. It has been found that both the clamping load and drawing loads are related with the geometry of the bead rather than the lubrication conditions.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.365-371
• /
• 2016

The electromechanical brake (EMB) is one of future brake systems due to its many advantages. For implementation of the EMB, the correct feed back about clamping force is necessary. Keeping commercialization of the EMB in mind, it is strongly demanded that an expensive load cell measuring the clamping force is replaced with an estimation algorithm. In addition, an estimation of the kissing point where the brake pads start to come into contact with a disk wheel is proposed in this paper. With these estimation algorithms, the clamping force can be expressed as a polynomial characteristic curve versus the motor angle. Also, a method for calibration of measured values by the load cell is proposed and used for an actual characteristic curve. Lastly, the performance of the proposed algorithms is evaluated in comparison with the actual curve on a developed EMB test bench.

• 한국정밀공학회지
• /
• 제26권3호
• /
• pp.113-121
• /
• 2009

Behavior of a package of a microwave oven under the clamping condition is evaluated by tests and the finite element analyses. PAM-CRASH software is used for the finite element analyses. Results of the analyses are compared with those of the tests and accuracy is shown to be favorable. Under the clamping condition of the original design, severe deformation occurs and an improved design of the outer case and upper EPS(Expandable Poly Styrene) is proposed to reduce it. Face beads of the outer case are introduced and shape of the upper EPS is modified to reduce the deformation resulting from the clamping load. The improved design model is analyzed and its deformation is shown to be satisfactory. A prototype is produced according to the improved design and tests are performed. Results of the clamping test of the prototype show that the plastic deformation is removed totally.

• 한국소음진동공학회논문집
• /
• 제18권8호
• /
• pp.849-855
• /
• 2008

다양한 조임 조건에서 기계적 조인트의 컨택 특성 파라미터를 유도하기 위하여 컨택 공진을 기반으로 하는 실험적 방법을 개발하였다. 기계적 조인트의 전단 컨택 강성과 감쇠의 파라미터는 접촉 표면간의 표면 처리, 윤활 유무, 그리고 조임력과 전단력의 의한 영향과 같은 여러 가지 물리적 조인터 파라미터와 연계하여 고찰하였다. 제안된 실험적 방법을 사용하여 전단 컨택 강성 값은 조임력과 전단력이 커짐에 따라 증가하는 것을 발견하였다. 또한 컨택 감쇠 비 값은 대부분 조임력과 상관없이 일정 값을 나타내지만 전단력이 커짐에 따라 감소하였다. 추가로, 전단 강성 값과 컨택 감쇠 비는 매끄러운 표면에서보다 거친 표면에서 더 크게 나타남을 알 수 있었다.

• 한국공간구조학회논문집
• /
• 제20권3호
• /
• pp.91-98
• /
• 2020

For form stability of membrane structures, membrane material is required to be in tension. Therefore, in planning and maintenance management, the engineer should consider enough about introduction of stress during construction and re-introduction of stress after completion. Clamping part is an important portion with the function for introducing tension into membrane materials, and the function to transmit stress to boundary structures, such as steel frames. Then, the purpose of this research is to clarify stress condition and stress transfer mechanism including clamping part of membrane structures, and to grasp the changing tendency of membrane structures with the passage of time. In this research, following previous one, we perform well-balanced evaluation by conducting tensile fractured tests of clamping part's specimens, and by measuring individually the amount of displacement of not only overall specimen's length but membrane material and clamping part. Thereby, we consider the influence the difference in the hardness of edge rope and the difference in the direction of thread affect modification and fracture load.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.84-89
• /
• 2005

The design of composite joint is a very important research area because they are often the weakest areas in composite structures. In this paper, the failure load of the mechanically fastened composite joint with the clamping force was predicted by the failure area index method. By the suggested failure area index method, the strength of the mechanically fastened composite joint could be predicted within 22.5% when clamping force was applied to the composite joint.