• Journal of Korean Society of Steel Construction
• /
• v.29 no.3
• /
• pp.205-215
• /
• 2017

This study presents an example of conceptual design for hollow circular section multi-column tower system subjected to 10MW level wind load by introducing a method based on member utilization that examine both structural stability and economical efficiency. The basic assumptions for the proto type of a multi-column tower that can replace a single-cylinder tower were suggested and structural models were constructed following the assumptions and analyzed for identifying member forces. Based on the calculated member strengths and acting loads, the member utilization of the proposed multi-column tower structures were calculated for axial force, shear, bending and torsion and evaluaed for suitability as a wind tower. Design parameters such as steel tube dimensions, slenderness ratio, and number of floors for braces was proposed in the acceptable range of member utilization for conceptual design of multi-column wind towers.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4A
• /
• pp.323-329
• /
• 2011

Most current design codes of concrete structures adopt the partial safety factor format to assure the proper safety margin or reliability against various limit states as a practical design tool. The safety factors, load and resistance factors and so on, are determined based on the theory of structural reliability, which takes into account the statistical uncertainties of both loads and resistances. The establishment of statistical models for load and resistance should be preceded the application of reliability theory. In this paper, especially the influence of the statistical variations of resistance models, which are described in terms of strength of concrete, strength of reinforcements and sectional dimensions and so on, are examined and the probabilistic models for resistance of reinforced concrete members were developed. The statistical data were collected on local tests and experiments in Korea and the Monte Carlo simulation (MCS) technique was used. The results of this paper may be useful and valuable in calibration of design code in this country.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.6
• /
• pp.595-603
• /
• 2015

With the advances of the big-data process technology, acquiring the real-time information from the massive image data taken by a mobile device inside a vehicle will be possible in the near future. Among the information that can be found around the vehicle, the route information is needed for safe driving. In this study, the automatic extraction of route information from the road sign imagery was dealt with. The scope of the route information in this study included the route number, route type, and their relationship with the driving direction. For the recognition of the route number, the modified Tesseract OCR (Optical Character Recognition) engine was used after extracting the rectangular-road-sign area with the Freeman chain code tracing algorithm. The route types (expressway, highway, rural highway, and municipal road) are recognized using the proposed algorithms, which are acquired from colour space analysis. Those road signs provide information about the route number as well as the roads that may be encountered along the way. In this study, such information was called “OTW (on the way)” or “TTW (to the way)” which between the two should be indicated is determined using direction information. Finally, the route number is matched with the direction information. Experiments are carried out with the road sign imagery taken inside a car. As a result, route numbers, route number type, OTW or TTW are successfully recognized, however some errors occurred in the process of matching TTW number with the direction.

• Computers and Concrete
• /
• v.16 no.1
• /
• pp.49-65
• /
• 2015

It is hard to guarantee the strict synchronization of all the jacking-up points in the integral jacking of a large-span continuous box girder bridge. This paper took the Hengliaojing Bridge as background, which need jacking up as an object with 295m length and more than 10,000tons weight, adopted 3D software to calculate the unsynchronized jacking-up working conditions, and studied the relationships between the unsynchronized vertical difference and the girder's deformation behaviour. The aim is to verify the maximum value of the unsynchronized vertical difference, and guide the construction and ensure safety. The monitoring system with its contents is introduced corresponding to the analysis. The results of the deck relative elevations prove that it is difficult to avoid the deck torsional deformation for jacking different; especially the side span shows more deformations for its smaller stiffness. The maximum difference is smaller than the limited value with acceptable stresses in the sections. The jacking heights of the pier in each construction step are controlled regularly according to the design. The shifting of the whole bridge in longitudinal direction is smaller than in transverse direction. The several beginning steps are the key to adjust their support reactions. This study is one parts of the fundamental research for the code "Technical specification for bridge jacking-up and reposition of China". The whole synchronous jacking project of the main bridge set a world record by the World Record Association for the whole bridge jacking project with the longest span of the world.

• Geomechanics and Engineering
• /
• v.12 no.4
• /
• pp.723-738
• /
• 2017

Rock is a heterogeneous material, which introduces complexity in the analysis of rock slopes, since both the existing discontinuities within the rock mass and the intact rock contribute to the degradation of strength. Rock failure is often catastrophic due to the brittle nature of the material, involving the sliding along structural planes and the fracturing of rock bridge. This paper proposes an advanced discretization method of rock mass based on block theory. An in-house software, GeoSMA-3D, has been developed to generate the discrete fracture network (DFN) model, considering both measured and artificial joints. Measured joints are obtained from the photogrammetry analysis on the excavation face. Statistical tools then facilitate to derive artificial joints within the rock mass. Key blocks are searched to provide guidance on potential reinforcement measures. The discretized blocky system is subsequently implemented into a discontinuous deformation analysis (DDA) code. Strength reduction technique is employed to analyze the stability of the slope, where the factor of safety can be obtained once excessive deformation of slope profile is observed. The combined analysis approach also provides the failure mode, which can be used to guide the choice of strengthening strategy if needed. Finally, an illustrated example is presented for the analysis of a rock slope of 20 m height inclined at $60^{\circ}$ using combined GeoSMA-3D and DDA calculation.

• Journal of Korean Society of Steel Construction
• /
• v.28 no.3
• /
• pp.163-171
• /
• 2016

For railway bridges, serviceabilities such as passenger comfort and train riding safety are important design requirements as well as the structural safety of the bridge. In this paper, dynamic responses of a steel box girder bridge by actual passing trains were measured and analyzed by probabilistic method. Deflections and accelerations data at center of side span were collected for about a month by various types of actual passenger and freight trains. Effects by axle weights, types of trains were analyzed. 100 and 200 years maximum values were estimated by Gumbel probability paper and compared with corresponding requirements in the current design code. Except for some cases of accelerations, estimated values were well below the criteria and exceedance probabilities were very low. More data for longer term and other types of bridges are needed to perform comprehensive analysis on the serviceability of railway bridges.

• Earthquakes and Structures
• /
• v.6 no.4
• /
• pp.375-392
• /
• 2014

Time history analyses have been preferred commonly in earthquake engineering area to determine earthquake performances of structures in recent years. Advances in computer technology and structural analysis have led to common usage of time history analyses. Eurocode 8 allows the use of real earthquake records as an input for linear and nonlinear time history analyses of structures. However, real earthquake records with the desired characteristics sometimes may not be found, for example depending on soil classes, in this case artificial and synthetic earthquake records can be used for seismic analyses rather than real records. Selected earthquake records should be scaled to a code design spectrum to reduce record to record variability in structural responses of considered structures. So, scaling of earthquake records is one of the most important procedures of time history analyses. In this paper, four real earthquake records are scaled to Eurocode 8 design spectrums by using SESCAP (Selection and Scaling Program) based on time domain scaling method and developed by using MATLAB, GUI software, and then scaled and real earthquake records are used for linear time history analyses of a six-storied building. This building is modeled as spatial by SAP2000 software. The objectives of this study are to put basic procedures and criteria of selecting and scaling earthquake records in a nutshell, and to compare the effects of scaled earthquake records on structural response with the effects of real earthquake records on structural response in terms of record to record variability of structural response. Seismic analysis results of building show that record to record variability of structural response caused by scaled earthquake records are fewer than ones caused by real earthquake records.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.22 no.7
• /
• pp.391-399
• /
• 2018

The site coefficients in the common requirements for seismic design codes, which were promulgated in 2017, were reevaluated and the standard design spectrum for soil sites were newly proposed in order to ensure the consistency of the standard design spectra for rock and soil sites specified in the common requirements. Using the 55 ground motions from domestic and overseas intraplate earthquakes, which were used to derive the standard design spectrum for rock sites, as rock outcropping motions, site response analyses of Korean soil were performed and its ground-motion-amplification was characterized. Then, the site coefficients for soil sites were reevaluated. Compared with the existing site coefficients, the newly proposed short-period site coefficient $F_a$ increased and the long-period site coefficient $F_v$ decreased overall. A new standard design spectrum for soil sites was proposed using the reevaluated site coefficients. When compared with the existing design spectrum, it could be seen that the proposed site coefficients and the standard design spectrum for soil sites were reasonably derived. They reflected the short-period characteristics of earthquake and soil in Korea.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.8
• /
• pp.65-73
• /
• 2013

Ground-coupled heat pump system has attracted attention as a promising renewable energy technology due to its improving energy efficiency and eco-friendly mechanism for space cooling and heating. Pipes buried in the ground play a role of direct thermal interaction between circulating fluid inside the pipe and surrounding soils in the geothermal exchange system. However, both complexities of turbulent flow coupling thermal-hydraulic phenomena and very long aspect ratio of the pipe make it difficult to model the heat exchange system directly. Energy balance for fluid flow inside the pipe was derived to model thermal-hydraulic phenomena, and one-dimensional pipe element was proposed through Galerkin formation and time integration of the equation. Developed element is combined to pre-developed FEM code for THM phenomena in porous media. Numerical results of Thermal Response Test showed that line-source model overestimates equivalent thermal conductivity of surrounding soils due to thermal interaction between adjacent pipes and finite length of the pipe. Thus, inverse analysis for the TRT simulation was conducted to present optimal transformation matrix with utmost convergence.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.4
• /
• pp.488-495
• /
• 2017

In this study, we conducted the kinetic hydration modeling of OPC and the final product according to the substitution ratio of GGBS by using the geochemical code, GEMS, in order to calculate the thermodynamic equilibrium. The thermodynamic data was used by GEMS's 3rd party database, Cemdata18, and the cement hydration model, the Parrot & Killoh model was applied to simulate the hydration process. In OPC modeling, ion concentration of pore solution and hydration products by mass and volume were observed according to time. In the GGBS modeling, as the substitution rate increases, the amount of C-S-H, which contributes the long-term strength, increases, but the amount of Portlandite decreases, which leads to carbonation and steel corrosion. Therefore, it is necessary to establish prevention of some deterioration.