• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.3
• /
• pp.246-253
• /
• 1996

In this paper, a problem that occurred in the telegraphist equation established by mode conversion method is solved as analysis tapered transmission line is applied to a waveguide taper. After comparing and analyzing the taper function with variant properties, we select on of taper functions not only that is easily designed but also that have good properties. And then we propose the applicant method to design the waveguide taper and deal with the design of mode transducer between rectangular waveguide and circular waveguide. The measured results of scattering coefficients for the mode transducer fabricated with designed data are agreed well with the theoretical results and the validity of the proposed design and analysis method has been confirmed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.4 s.107
• /
• pp.351-357
• /
• 2006

In this paper, a direct $TM_{01}-TE_{11}$ mode converter of circular waveguide which is used the approximated design method of mode conversion between $TM_{01}$ and $TE_{11}$ modes is designed for radiation with the maximum directivity of high power energy into air (rom high power microwave antenna system. The proposed direct $TM_{01}-TE_{11}$ mode converter is calculated and designed with an approximated method for non-linear function about an extended non-constant serpentine type of circular waveguide. Then, the designed mode converter is optimized by length of 200 mm and efficiency above 95% by FIM simulation and achieved short length and high efficiency of the antenna by results of fabricated and measured characteristics.

• ETRI Journal
• /
• v.46 no.3
• /
• pp.404-412
• /
• 2024

We propose a method for increasing the bandwidth of a substrate-integrated-waveguide (SIW) cavity-backed antenna with taper-based micro-strip SIW transition feeding. For radio transmission, a circular slot is etched on top of the SIW cavity. For optimal antenna design, the slot is etched slightly away from the cavity center to generate circularly polarized waves. Simulations show a wide axial ratio bandwidth of 7.860% between 11.02 GHz and 11.806 GHz. Experimental results confirm a similar wide axial ratio bandwidth of 4.9% between 10.8 GHz and 11.35 GHz. An SIW feed from an inductive window excites the radiating circular slot, resulting in a simulated wide impedance range of 1.548 GHz (10.338 GHz-11.886 GHz) and bandwidth of 13.93%. Experimental results show a wide impedance of 2.08 GHz (10.2 GHz-12.08 GHz) and bandwidth of 18.84%. The SIW cavity-backed antenna creates a unidirectional pattern, leading to gains of 6.61 dBi and 7.594 dBi in simulations and experiments, respectively. The proposed antenna was fabricated on a Rogers RT/Duroid 5880 substrate, and the reflection coefficient, radiation patterns, and gains were tested and compared using a computer simulator. The developed broadband antenna seems suitable for X-band applications.

• Journal of the Optical Society of Korea
• /
• v.15 no.1
• /
• pp.82-89
• /
• 2011

In this paper, we numerically study both band-pass and band-stop plasmonic filters based on Metal-Insulator-Metal (MIM) waveguides and circular ring resonators. The band-pass filter consists of two MIM waveguides coupled to each other by a circular ring resonator. The band-stop filter is made up of an MIM waveguide coupled laterally to a circular ring resonator. The propagating modes of Surface Plasmon Polaritons (SPPs) are studied in these structures. By substituting a portion of the ring core with air, while the outer dimensions of the ring resonator are kept constant, we illustrate the possibility of red-shift in resonant wavelengths in order to tune the resonance modes of the proposed filters. This feature is useful for integrated circuits in which we have limitations on the outer dimensions of the filter structure and it is not possible to enlarge the dimension of the ring resonator to reach to longer resonant wavelengths. The results are obtained by a 2D finite-difference time-domain (FDTD) method. The introduced structures have potential applications in plasmonic integrated circuits and can be simply fabricated.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.7
• /
• pp.823-830
• /
• 2010

This paper deals with a coaxial-to-waveguide transition generating circularly polarized wave to be connected with horn antennas. By combining vertical coaxial fed structure, back-short and the polarization twisting structure, the circular polarization is successfully generated in the waveguide. The designed and implemented transition shows that the present structure can significantly reduce the size of the antenna part at X-band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.1
• /
• pp.49-60
• /
• 2017

In this paper, we presented the result of the study on high-power handling capability of the X-band circular waveguide cavity filter configured at the output of high power amplifier(120 W) for geostationary satellites. The dual mode circular waveguide cavity filter with 6th order is selected and the physical model of the filter is designed after determination of the size of resonator from mode chart. Multipactor margin analysis is performed by the SEM method and the VMF method. The result shows that the VMF method predicts lower multipactor breakdown thresholds than the SEM method. Evaluating the multipactor margin obtained by the VMF method to ECSS criteria, we could decide to perform multipactor test. The multipactor test conducted in ESA facility shows that multipactor did not occur even until the RF power increased up to 540 W. In consequence, by both analysis and test, we could verify that the X-band circular waveguide cavity filter has the sufficient high-power handling capability to operate on orbit.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.4
• /
• pp.380-386
• /
• 2014

In this paper, a higher-order mode coupler using coaxial-structure waveguide for Ku-band monopulse satellite tracking is proposed. The proposed higher-order mode coupler is built in a coaxial structure for compactness and weight reduction, making it suitable for mobile tracking systems. The inner circular waveguide of coaxial-structure is used to extract the fundamental mode signal and the high-order mode signal is extracted from the four slots of the outer circular waveguide and then transmitted via given stepped rectangular waveguide structure. The simulated results show that proposed higher-order mode coupler covers 250 MHz(12.75 GHz ~ 13.00 GHz) bandwidth with return loss and insertion loss characteristics. The antenna patterns of fundamental mode and higher-order mode applicable to monopulse tracking are generated successfully. Designed higher-order mode coupler using coaxial waveguide structure for Ku-band is expected to be used for high precision monopulse satellite tracking systems.

• Journal of Energy Engineering
• /
• v.25 no.1
• /
• pp.86-91
• /
• 2016

Convenient design guideline for Waveguide-below-cutoff (WBC) array is proposed to obtain the minimum waveguide length for electromagnetic pulse (EMP) shielding. The analysis includes circular, rectangular, and hexagonal WBC, determine the total length of the waveguide. When the unit side of rectangular WBC and the diagonal line of hexagonal WBC are given as 30 mm, the length of hexagonal WBC is 5 mm shorter than rectangular case with shielding effectiveness (SE) 80 dB. The length difference is deepened with SE of 100 dB, which shows approximately 30 mm shorter length for hexagonal case than others. In addition, hexagonal WBC requires much shorter length than circular WBC. In conclusion, hexagonal case is the most effective with respect to flow velocity and pressure loss for equivalent SE.

• Journal of Astronomy and Space Sciences
• /
• v.27 no.3
• /
• pp.239-244
• /
• 2010

A simulation for the design of a $90^{\circ}$ differential phase shifter aimed toward Korean VLBI Network (KVN) 129 GHz band polarizer is described in this paper. A dual-circular polarizer for KVN 129 GHz band consists of a $90^{\circ}$ differential phase shifter and an orthomode transducer. The differential phase shifter is made up of a square waveguide with two opposite walls loaded with corrugations. Three-dimensional electromagnetic simulation has been performed to predict the $90^{\circ}$ differential phase shifter's characteristics. The simulation for the differential phase shifter shows that the phase shift is $90^{\circ}{\pm}3.3^{\circ}$ across 108-160 GHz and the return losses of two orthogonal modes are better than -30 dB within the design frequency band. According to the simulation results the calculated performance is quite encouraging for KVN 129 GHz band application.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.2
• /
• pp.126-133
• /
• 2009

In this paper, The planar waveguide slotted antenna is presented for a satellite communication of vehicles. In stead of the microstrip patch array antenna having a dielectric loss and a feeding loss, the proposed antenna has the 3-layered waveguide feeding network structure for assembling easily. Also this antenna can receive mechanically both RHCP and LHCP transmitted from a satellite using a polarizer made from a thin single layer film. The Gain of the proposed 4X8 array antenna is 27.5dB and the gain of 8X16 array antenna is 32dB.