• 한국항공우주학회지
• /
• 제48권7호
• /
• pp.505-511
• /
• 2020

원형 복합재 튜브를 고고도 장기체공 무인기의 주요 스파에 사용하였다. 본 논문에서는 수정된 Brazier 방법을 이용하여 비대칭으로 보강된 원형 스파의 파단하중을 예측할 수 있는 이론적인 모델을 제안하였다. 이 모델을 이용하여 비대칭으로 보강된 원형스파의 최대 허용 굽힘 모멘트를 예측하였다. 해석 결과로부터 원형 스파의 상단에 위치한 보강된 캡은 최대 허용 굽힘 모멘트를 증가시키는 것을 알 수 있다. 4점 굽힘 실험을 수행하여 스파 캡이 파손하중에 미치는 영향을 평가하였고 제안된 모델과 비교하였다. 그리고 수치해석을 수행하여 보강된 원형 스파의 거동을 분석하였다. 제안된 이론적인 모델은 실험 및 수치해석 결과와 잘 일치함을 보였다.

• 한국항공운항학회지
• /
• 제27권1호
• /
• pp.51-56
• /
• 2019

To reduce the structural weight, thin-walled circular composite tube has been used as a main spar of high altitude-long endurance unmanned air vehicle(HALE UAV). Predicting the torsional response of stiffened circular spar is complex due to the inhomogeneous nature of section properties, which are dependent on fiber architecture and constituent material properties. The stiffener were placed in the top and bottom sectors of a tube to increase the torsional capabilities such as the rigidity and buckling strength. Numerical simulations were performed to estimate the effect of the stiffener on the torsional capacities. A static experimental test was performed on a stiffened tube, and the test results were compared with a numerical model. The numerical models showed good correlation and demonstrated the ability to predict the torsional capacity. Results presented herein will exhibit the effectiveness of stiffener on torsional strength and stiffness.

• 한국항공우주학회지
• /
• 제47권10호
• /
• pp.687-694
• /
• 2019

초경량 항공기 구조의 날개 보로 사용되는 원통형 복합재료 날개 보는 굽힘 모멘트와 전단하중을 동시에 받고 있는 구조물이다. 하지만 기존의 일반 원통형 보는 상하부의 굽힘 모멘트, 좌우부의 전단하중을 지지하는 구조적 특성을 고려하지 못하므로 비효율적일 수 있다. 따라서 섬유각 또는 복합재료를 적절히 배열하여 효율적으로 구조물을 만드는 것이 필요하다. 본 연구에서는 원통형 복합재료 보의 굽힘강도와 전단강도의 증가를 위해 보의 단면을 상하좌우로 분할하여 적층순서를 달리함으로써 효율적인 하중지지가 가능하게 하였다. 상용 프로그램 MSC/NASTRAN을 이용한 구조해석을 통해 원호 분할각과 섬유각에 따른 수직변위, 수직변형률, 전단변형률 계산하였다. 계산 결과에 따르면 새롭게 제안된 원통형 보의 분할각과 섬유 방향각을 선택하여 구조 강도를 증가시킬 수 있음을 제시하였다.

• Ocean Systems Engineering
• /
• 제1권4호
• /
• pp.285-296
• /
• 2011

Spar platforms have several advantages for deploying wind turbines in offshore for depth beyond 120 m. The merit of spar platform is large range of topside payloads, favourable motions compared to other floating structures and minimum hull/deck interface. The main objective of this paper is to present the response analysis of the slack moored spar platform supporting 5MW wind turbine with bottom keel plates in regular and random waves, studied experimentally and numerically. A 1:100 scale model of the spar with sparD, sparCD and sparSD configuration was studied in the wave basin ($30{\times}30{\times}3m$) in Ocean engineering department in IIT Madras. In present study the effect of wind loading, blade dynamics and control, and tower elasticity are not considered. This paper presents the details of the studies carried out on a 16 m diameter and 100 m long spar buoy supporting a 90 m tall 5 MW wind turbine with 3600 kN weight of Nacelle and Rotor and 3500 kN weight of tower. The weight of the ballast and the draft of the spar are adjusted in such a way to keep the centre of gravity below the centre of buoyancy. The mooring lines are divided into four groups, each of which has four lines. The studies were carried out in regular and random waves. The operational significant wave height of 2.5 m and 10 s wave period and survival significant wave height of 6 m and 18 s wave period in 300 m water depth are considered. The wind speed corresponding to the operational wave height is about 22 knots and this wind speed is considered to be operating wind speed for turbines. The heave and surge accelerations at the top of spar platform were measured and are used for calculating the response. The geometric modeling of spar was carried out using Multisurf and this was directly exported to WAMIT for subsequent hydrodynamic and mooring system analysis. The numerical results were compared with experimental results and the comparison was found to be good. Parametric study was carried out to find out the effect of shape, size and spacing of keel plate and from the results obtained from present work ,it is recommended to use circular keel plate instead of square plate.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.175-182
• /
• 2016

Recently, carbon fiber-reinforced composite is widely used in many aerospace applications. Among most of the aerospace vehicles, human-powered aircraft essentially uses it for minimizing the weight of the vehicle and gaining high stiffness to increase its efficiency. In this paper, main wing spar of the human-powered aircraft is investigated. Finite element models were created based on the baseline model built in 2013 to make analysis of cross-section of the spar with varying ply angles of each layer of the spar. Objective function, which is affected from bending rigidity, torsional rigidity, and strength ratio, was evaluated for every cases. The model of 2013 and present cases were put into comparison by values evaluated from objective function. From the comparison, it was concluded that there are more chances to improve the baseline model to make the vehicle better in stiffness and weight than the model of 2013.

• EDISON SW 활용 경진대회 논문집
• /
• 제6회(2017년)
• /
• pp.304-310
• /
• 2017

In this paper, various webs of I-shaped beam used in aircraft spars are examined. Under the assumption that an aircraft spar is a cantilevered beam with a constant cross-section and is subjected to only bending, four kinds of webs are analyzed for three different sizes. To enable comparison, each hole has the same area and are subjected to the same load by using EDISON 2D Continuum analysis. While circular hole is the most often used, elliptic one is obtained with the minimum von-Mises stress by about 40% decreased. To verify the results gathered by EDISON, comparison was made with ANSYS and analytic predictions obtained with the stress intensity factor K. As comparison shows insignificant discrepancies, it is concluded that a well-designed beam with elliptic holes will be the most efficient spar regarding weight to rigidity ratio in terms of the bending stress.

• 한국해양공학회지
• /
• 제27권5호
• /
• pp.43-50
• /
• 2013

In the present investigation, the hydrodynamic characteristics of a vertically floating hollow cylinder in regular waves have been studied. The potential theory for solving the diffraction and radiation problem was employed by assuming that the heave response motion was linear. By using the matched eigenfunction expansion method, the characteristics of the exciting forces, hydrodynamic coefficients, and heave motion responses were investigated with various system parameters such as the radius and draft of a hollow cylinder. In the present analytical model, two resonances are identified: the system resonance of a hollow cylinder and the piston-mode resonance in the confined inner fluid region. The piston resonance mode is especially important in the motion response of a hollow circular cylinder. In many cases, the heave response at the piston resonance mode is large, and its resonant frequency can be predicted using the empirical formula of Fukuda (1977). The present design tool can be applied to analyze the motion response of a spar offshore structure with a moon pool.

• 한국해양공학회지
• /
• 제30권2호
• /
• pp.91-99
• /
• 2016

The global demand for oil and natural gas has increased, and resource development is moving to the deep sea. Floating and flexible offshore structures such as semi-submersible, spar, and FPSO structures have been widely used. The major equipment of floating structures is always exposed to waves, currents, and other marine environmental factors, which cause structural damage. Moreover, flexible risers are susceptible to an exciting force due to the motion of the floating body. The inline and transverse responses from the three-dimensional behavior of a floating structure occur because of various forces. Typical risers are made of steel pipe and applied in the oil and gas development field, but flexible materials such as polyethylene are suitable for OTEC risers. Consequently, the optimal design of a flexible offshore plant requires a dynamic behavior analysis of slender bodies made of the different materials commonly used for offshore flexible risers. In this study, a three-dimensional motion measurement device was used to analyze the displacements of riser models induced by external force factors, and forced oscillation of a riser was linked to forced oscillation under a steady flow and regular wave condition.

• Ocean Systems Engineering
• /
• 제6권2호
• /
• pp.143-159
• /
• 2016

Cargo, such as a Tension Leg Platform (TLP), Semi-submersible platform (Semi), Spar or a circular Floating Production Storage and Offloading (FPSO), are frequently dry-transported on a Heavy Lift Vessel (HLV) from the point of construction to the point of installation. The voyage can span months and the overhanging portions of the hull can be subject to frequent wave slamming events in rough weather. Tie-downs or sea-fastening are usually provided to ensure the safety of the cargo during the voyage and to keep the extreme responses of the cargo, primarily for the installed equipment and facilities, within the design limits. The proper design of the tie-down is dependent on the accurate prediction of the wave slamming loads the cargo will experience during the voyage. This is a difficult task and model testing is a widely accepted and adopted method to obtain reliable sea-fastening loads and extreme accelerations. However, it is crucial to realize the difference in the inherent stiffness of the instrument that is used to measure the tri-axial sea fastening loads and the prototype design of the tie-downs. It is practically not possible to scale the tri-axial load measuring instrument stiffness to reflect the real tie-down stiffness during tests. A correlation method is required to systematically and consistently account for the stiffness differences and correct the measured results. Direct application of the measured load tends to be conservative and lead to over-design that can reflect on the overall cost and schedule of the project. The objective here is to employ the established correlation method to provide proper high-frequency responses to topsides and hull design teams. In addition, guidance for optimizing tie-down design to avoid damage to the installed equipment, facilities and structural members can be provided.

• 대한기계학회논문집B
• /
• 제33권12호
• /
• pp.1007-1013
• /
• 2009

The purposes of this study are to evaluate the power performance through CFD analysis and structural integrity through uni-directional FSI analysis in aerodynamic design and structure design of wind turbine blade. The blade was designed to generate the power of 2MW under the rated wind speed of 11 m/s, consisting of NACA 6 series, DU series and FFA series airfoil. The inside section of the blade was designed into D-spar structure and circular stiffener was placed to reinforce the structural strength in the part of hub. CFD analysis with the application of transitional turbulence model was performed to evaluate the power performance of blade according to the change of TSR and 2.024MW resulted under the condition of rated wind speed. TSR of 9 produced the maximum power coefficient and in this case, Cp was 0.494. This study applied uni-directional FSI analysis for more precise evaluation of structural integrity of blade, and the results of fiber failure, inter fiber failure and eigenvalue buckling analysis were evaluated, respectively. For the evaluation, Puck's failure criteria was applied and the result showed that fiber failure and inter fiber failure did not occur under every possible condition of the analysis. As a result, power performance and structural integrity of 2 MW blade designed in this study turned out to satisfy the initial design goals.