• 공업화학
• /
• 제16권2호
• /
• pp.180-186
• /
• 2005

본 논문은 유기물과 중금속이 함께 포함되어 있는 폐수 슬러지의 시멘트 고형화를 위해 포졸란물질인 실리카흄을 고화보조재로 사용한 연구결과이다. 실리카흄을 고화보조재로 사용할 경우 고화체의 일축압축강도는 현저히 증가하는 결과를 보여주었으며, 실리카흄의 시멘트 대체가 전체 배합물의 15%까지 증가하였을 때 일축압축강도는 실리카흄을 전혀 사용하지 않았을 경우에 비하여 66.7%까지 증가하는 결과를 보여주었다. 또한 시멘트가 실리카흄으로 대체되는 양이 증가하면서 총 유기탄소와 중금속인 크롬의 용출량은 감소하는 결과를 보여주었으며, 배합물 중 실리카흄이 5%를 차지할 때 중성의 용출액에서 총 유기탄소의 85%가 용출억제되었으며, 산성의 용출액에서 0.76 mg-Cr/g-Cr의 크롬만이 용출되었다. 전자주사현미경과 X-선 회절분석, 적외선 분광분석 등을 이용한 미세구조분석 결과 실리카흄은 시멘트경화 초기에 크링커 입자를 피복하여 초결(initial setting)과 수화를 저해하는 에트링가이트(ettringite)의 형성을 감소시키는 것으로 나타났다. 본 연구결과 중금속과 유기물이 혼합된 슬러지의 시멘트 고형화에 있어서 실리카흄의 첨가는 유기물질이 시멘트 수화반응에 미치는 악영향을 억제하고 중금속 및 유기물의 용출을 감소시키는 것으로 나타났다.

• 폴리머
• /
• 제27권4호
• /
• pp.275-284
• /
• 2003

접착성이 없는 고밀도 폴리에틸렌 (HDPE)과 나노입자 카본블랙 복합체를 대상으로 전극과의 계면 접착 향상과 고분자 가교 특성에 따른 양온도 계수 (PTC) 특성을 연구하였다. 은페이스트를 전극으로 사용하였을 때에는, 전극과 HDPE의 접착 계면 저항으로 인하여 카본함량이 45 wt% 이상에서 1 $\Omega$ 이었으나, 덴드라이트 (dendrite)된 구리 전극의 경우 HDPE와 전극간의 넓은 면적 접촉에 의한 계면 저항이 0.2 $\Omega$ 이하였다. HDPE와 은페이스트의 계면 저항의 증가로 인하여 구리 박막을 사용하였을 때보다 전체적으로 저항이 높게 나타났다. HDPE와 나노입자 카본블랙 복합체는 온도가 증가하여 HDPE의 비캣연화온도까지는 저항이 일정하게 유지하다가, HDPE의 연화점에서 증가하기 시작하여 용융점에서 극대 값을 나타내는 전형적인 PTC특성을 보여주었다. 일반적으로 HDPE의 용융점을 넘어서면 음온도 계수 (NTC) 현상이 나타나는데, 가교결합을 시킨 HDPE의 경우는, 용융점 이상에서 NTC 현상이 나타나지 않고 저항이 일정하게 유지되거나 증가하는 경향이 나타났다. 구리 (copper) 전극과 고분자와의 계면 접촉 면적을 증가시키기 위하여 크롬 (chromium)을 덴드라이트시킨 전극을 사용하여 계면 접촉 저항을 감소시켰다.

• 한국재료학회지
• /
• 제33권4호
• /
• pp.124-129
• /
• 2023

This study assessed the influences of fluorine introduced into DLC films on the structural and mechanical properties of the sample. In addition, the effects of the fluorine incorporation on the compressive stress in DLC films were investigated. For this purpose, fluorinated diamond-like carbon (F-DLC) films were deposited on cobalt-chromium-molybdenum substrates using radio-frequency plasma-enhanced chemical vapor. The coatings were examined by Raman scattering (RS), Attenuated total reflectance Fourier transform infrared spectroscopic analysis (ATR-FTIR), and a combination of elastic recoil detection analysis and Rutherford backscattering (ERDA-RBS). Nano-indentation tests were performed to measure hardness. Also, the residual stress of the films was calculated by the Stony equation. The ATR-FTIR analysis revealed that F was present in the amorphous matrix mainly as C-F and C-F₂ groups. Based on Raman spectroscopy results, it was determined that F made the DLC films more graphitic. Additionally, it was shown that adding F into the DLC coating resulted in weaker mechanical properties and the F-DLC coating exhibited lower stress than DLC films. These effects were attributed to the replacement of strong C = C by feebler C-F bonds in the F-DLC films. F-doping decreased the hardness of the DLC from 11.5 to 8.8 GPa. In addition, with F addition, the compressive stress of the DLC sample decreased from 1 to 0.7 GPa.

• 미생물학회지
• /
• 제36권4호
• /
• pp.279-284
• /
• 2000

페놀을 유일한 탄소 및 에너지원으로 이용할 수 있는 Rhodococcus sp. CP01을 침출수로부터 분리하고 회분식 및 연속배양 체제에서 크롬(VI)을 동시에 환원시키는 능력을 추정하였다. 크롬(VI) 환원의 최적 pH 7.0과 페놀 농도 1,000 mg/L에서 최소배지에 주어진 0.25 mM의 크롬(VI)은 CP01 균주에 의해 60시간만에 완전히 환원되었으며, 이때 크롬의 환원속도는 4.17 $\mu$M/hr, 페놀의 분해속도는 38.4 mg.$L^{-1}$.$hr^{-1}$로 측정되었다. 수리학적 체류시간을 100hr으로 유지한 호기성 연속배양 체제에서 크롬(VI)의 농도를 0.0625, 0.125, 그리고 0.25 mM로, 페놀 농도를 1,000~4,000 mg/L까지 변화시키면서 46인간 운전한 결과, 크롬(VI) 0.125 mM과 페놀 3,000 mg/L일 때 유사 steady state에 이르렀으며 이때 크롬의 환원율은 거의 100%로 일정하게 유지되었다. 이 구간에서 계산된 specific reduction rate는 0.34 mg Cr(VI).g $protein^{-1}$.$hr^{-1}$로서 glucose를 생장기질로 이용한 기존의 연구 결과와 유사한 수준으로 나타났다. 이상의 결과로부터 본 연구는 중금속 크롬(VI)과 방향족 화합물인 페놀을 동시에 효과적으로 제거할 수 있는 생물학적 처리 가능성을 보여 주었다.

• 멤브레인
• /
• 제28권4호
• /
• pp.252-259
• /
• 2018

실 산성 도금폐수를 입상활성탄(GAC)이 유동메디아로 첨가된 유동상 멤브레인 반응기를 이용하여 처리하였다. GAC 유동조건에서 적용 투과플럭스에 대해 시간에 따른 흡입압의 증가는 관찰되지 않았다. 폐수의 중성 pH에서 파울링 속도는 산성 조건에 비해 GAC 유동조건에서 크게 감소하였다. 해당 폐수의 용액 pH 증가는 입자크기의 증가를 가져왔고 이는 멤브레인 표면에서 상대적으로 성긴 구조의 케이크층 형성을 야기시켰다. 유동상 멤브레인 반응기에서 GAC 유동 하에 95%이상의 COD 제거율이 관찰되었으며 총부유물질은 거의 완벽하게 제거되었다. 실 도금폐수의 pH에서, 유동상 멤브레인 반응기의 구리 및 크롬의 제거는 거의 관찰 되지 않았다. 그러나 pH를 중성으로 증가 시켰을 시 구리와 크롬의 제거율은 각각 99%와 94%까지 증가를 하였다. 적용해 준 pH에 상관 없이, 시안의 경우 95% 이상의 제거율을 달성하였다. 이는 유기물과 시안 착물 형성으로 인해 유동상 멤브레인 반응기 내 GAC의 강한 흡착으로 제거된 것으로 사료된다.

• Journal of Welding and Joining
• /
• 제2권1호
• /
• pp.4-17
• /
• 1984

Overlaid weld metals of austenitic stainless steel in a pressure vessel of power reactor are usually post-weld heated for a long period of time after welding. The PWHT is considered as a kind of sensitizing and it is important to check the soundness of the weld metal after PWHT, especially about the precipitation of carbides. The purpose of this report is to obtain information on the relation between the change of microstructure and Post-Weld Heat Treatment in the overlaid weld metals. Metallurgical aspects of the problem on austenitic stainless steel heated at $625^{\circ}C$, $670^{\circ}C$, $720^{\circ}C$ and $760^{\circ}C$ for 3, 10, 30, 100 and 300 hours have been investigated by means of optical-micrography, micro-hardness measurement, scanning electron microscope and electron-probe micro analysis. From the results obtained, the following conclusions are drawn; 1) The PWHT above $625^{\circ}C$ for a long time causes a diffusion of carbon atoms from low alloy steel into stainless steel, and consequently carbon is highly concentrated at the boundary layer of stainless steel. 2) C in ferritic steel migrated to austenitic steel and carbides precipitated in austenitic steel along fusion line. At higher temperatures, the ferrite grains coarsened in the decarburized zone. 3) In the change of microstructure of stainless steel overlaid weld metal, the width of carbides precipitated zone and decarburized zone increased with increase of PWHT temperature and time. 4) At about $625^{\circ}C$ to $760^{\circ}C$, chromium carbides, mainly $M_{23} C_6$, precipitate very closely in the carburized layer with remarkable hardening. 5) Precipitation of delta ferrite from molten weld metal depends on solidification phenomenon. There was a small of ferrite near the bond in which the local solidification time was short, comparing with after parts of weld metal. Shape and amount of ferrite were not changed by Post-Weld Heat Treatment after solidification.

• Nuclear Engineering and Technology
• /
• 제42권5호
• /
• pp.568-575
• /
• 2010

Flow Accelerated Corrosion is an active degradation mechanism of CANDU feeder. The tight bend downstream to Gray loc weld connection, close to reactor face, suffers significant wall thinning by FAC. Extensive in-service inspection of feeder wall thinning is very difficult because of the intense radiation field, complex geometry, and space restrictions. Development of a knowledge-based inspection program is important in order to guarantee that adequate wall thickness is maintained throughout the whole life of feeder. Research results and plant experiences are reviewed, and the plant inspection databases from Wolsong Units One to Four are analyzed in order to support developing such a knowledge-based inspection program. The initial thickness before wall thinning is highly non-uniform because of bending during manufacturing stage, and the thinning rate is non-uniform because of the mass transfer coefficient distributed non-uniformly depending on local hydraulics. It is obvious that the knowledge-based feeder inspection program should focus on both fastest thinning locations and thinnest locations. The feeder wall thinning rate is found to be correlated proportionately with QV of each channel. A statistical model is proposed to assess the remaining life of each feeder using the QV correlation and the measured thicknesses. W-1 feeder suffered significant thinning so that the shortest remaining life barely exceeded one year at the end of operation before replacement. W-2 feeder showed far slower thinning than W-1 feeder despite the faster coolant flow. It is believed that slower thinning in W-2 is because of higher chromium content in the carbon steel feeder material. The average Cr content of W-2 feeder is 0.051%, while that value is 0.02% for W-1 feeder. It is to be noted that FAC is reduced substantially even though the Cr content of W-2 feeder is still very low.

• 상하수도학회지
• /
• 제23권6호
• /
• pp.843-853
• /
• 2009

The sediment samples were collected from Seonakdong River and were analyzed for sulfide species such Acid Volatile Sulfide(AVS) and Elemental Sulfur(ES) and Chromium Reducible Sulfide(CRS). Then characteristics of the formation of sulfide species were investigated for six selected samples. Finally the relationship between environmental factors and sulfate reducing rate(SRR) was investigated using two selected samples. Concentrations of AVS and CRS were relatively high, which suggests that organics input to the sediments has been continued until recently and that potential of heavy metals leaching from the sediments is low. SRR in the sediments was closely related to fraction of fine particles(silt+clay) and also to dissolved organic carbon content of the sediment(DOCsed). The dependences of environmental factors such as organic content, temperature, sulfate concentration on the SRR was relatively strong in the selected experiments conducted with the samples from Noksan gate and Daejeo gate samples. The environmental factor dependencies were stronger in the Noksan gate samples than in the Daejeo gate samples, which is probably due to higher surface area of the Noksan gate sediments.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.115.2-115.2
• /
• 2010

Autothermal reforming(ATR) processes of hydrocarbon liquids such as diesel fuels are spotlighted as methods to produce hydrogen for Fuel cell. However, the use of heavy hydrocarbons as feedstocks for hydrogen production causes some problems which increase the catalyst deactivation by the carbon deposition. Coking can be inhibited by increasing the water dissociation on the catalyst surface. This results in catastrophic failure of whole system. Performance degradation of diesel autothermal reforming leads to increase of undesirable hydrocarbons at reformed gases and subsequently decrease the performance. In this study, perovskite-based catalysts were investigated as alternatives to substitute the noble metal catalyst for the ATR of diesel. The investigated perovskite structure was based on LaCrO3. and metals were added at the A-site to enhance oxygen ion mobility, transition metals were doped on the B-site to enhance the reformation. Substituted Lanthanum chromium perovskite were made by aqueous combustion synthesis, which can produce high surface area. And for the homogeneous fuel supply, we made ultrasonic injection system for reforming. We compared durability of evaporation system and ultrasonic system for fuel injection.

• Nuclear Engineering and Technology
• /
• 제52권3호
• /
• pp.647-653
• /
• 2020

Stainless steel is used commonly in nuclear applications for shielding radiation, so in this study, three different types of new stainless steel samples were designed and developed. New stainless steel compound ratios were determined by using Monte Carlo Simulation program Geant 4 code. In the sample production, iron (Fe), nickel (Ni), chromium (Cr), silicium (Si), sulphur (S), carbon (C), molybdenum (Mo), manganese (Mn), wolfram (W), rhenium (Re), titanium (Ti) and vanadium (V), powder materials were used with powder metallurgy method. Total macroscopic cross sections, mean free path and transmission number were calculated for the fast neutron radiation shielding by using (Geant 4) code. In addition to neutron shielding, the gamma absorption parameters such as mass attenuation coefficients (MACs) and half value layer (HVL) were calculated using Win-XCOM software. Sulfuric acid abrasion and compressive strength tests were carried out and all samples showed good resistance to acid wear and pressure force. The neutron equivalent dose was measured using an average 4.5 MeV energy fast neutron source. Results were compared to 316LN type stainless steel, which commonly used in shielding radiation. New stainless steel samples were found to absorb neutron better than 316LN stainless steel at both low and high temperatures.