• Journal of the Korean institute of surface engineering
• /
• v.19 no.2
• /
• pp.31-43
• /
• 1986

The properties of the electroless nickel deposit mainly depends on the pH of the bath, the plating temperature, and the molar ratio of nickel to hypophosphite but they are also affected by its formulation and concentration of complexing and buffering agents. According to changeing the concentration of triethanolamine and boric acid, phosphorous contents, microsturcture, crystalline, hardness and wear resistance of deposits obtained from ammoniacal alkaline bath were investigated by EPMA, differential thermal analyser, X-ray diffractometer and wear tester. The results are as follows; (1) Increasing concentration of triethanolamine in the bath, the deposits is slightly inclined to increase its phosphorous content(3.7% P). (2) In the as-plated state, the deposits are not crystallized state but they are thermally unstable phase, and they are crystallized with precipitating $Ni_3P$ at 400$^{\circ}C$. (3) The deposit containing 2.3% P has higher hardness value in the as plated and heat treated state at below 300$^{\circ}C$ than those of 3.7% phosphorous deposit (1090Hk). But in the case of heat treating at 400$^{\circ}C$, the former has lower hardness value (1000Hk) than the latter and has remarkably Ni(III) orientation by heat treatment. (4) The 3.7% phosphorous deposit heat treated at 400$^{\circ}C$ has better wear resistance than hard chromium plating.

• Journal of the Korean Chemical Society
• /
• v.38 no.9
• /
• pp.667-675
• /
• 1994

The precipitate flotation using $La(OH)_3$ as a coprecipitant was studied for the simultaneous determination of trace three elements in a sea water. Several experimental conditions such as pH, coprecipitant and surfactant were investigated with an artificial sea water. To remove the influence of Cr(VI) the Cr(VI) was reduced to Cr(III) using $NaBH_4$ prior to the flotation. Trace amounts of Cu(II), Co(II) and total Cr in 1.0 l sea water was coprecipitated together with the precipitation of $La(OH)_3$ in the solution of pH 9.8 adjusted with 3.OM NaOH solution. The precipitate was floated by using a mixed surfactant (1 to 8 of each 0.5% ethanolic sodium oleate and sodium dodecylsulfate solution) by bubbling a nitrogen gas. The floats was separated and filtrated from the mother liquor by suction. The precipitate was dissolved in 7.0 M $HNO_3$ solution and then marked to 25.0 ml with a deionized water. These elements were determined by graphite fumace atomic absorption spectrophotometry. This method was applied to determine the elements in the sea water of the Eastern and Western coasts. And the recoveries were over 90.0% in the samples into which given amounts of the analyte elements were spiked.

• The korean journal of orthodontics
• /
• v.25 no.1 s.48
• /
• pp.43-54
• /
• 1995

This study was conducted to examine the metal release of TiN-plated stainless steel orthodontic appliances by constructing the simulated orthodontic appliances equivalent to maxillary half arch, by dividing into TiN-plated and TiN-nonplated Bloops and by dividing again these groups into welded and nonwelded groups. And then, the total quantity of metal release was obtained by measuring the amounts of both soluble and precipitated nickel and chromium after immersing in artificial saliva for 15 days. And then, the corrosion appearance of surface structure was observed by using SEM. The results of this study were summarized as follows. 1. The total amounts of released nickel and chromium showed that the TiN-plated group after welding(Group 1) was 25.46 ${\mu}g$, respectively, and 17.4 ${\mu}g$, while the TiN-nonplated group after welding(Group III) was 54.69 ${\mu}g$, respectively, and 85.27 ${\mu}g$. Then, the TiN-Plated group indicated less amounts of metal release(p<0.05). 2. The total amounts of the TiN-plated group without welding(Group II) was 0.05${\mu}g$ and 0.34${\mu}g$, respectively. Then, it was shown that the TiN-plated group without welding(Group II) indicated less metal release than that of the TiN-Plated group after welding(Group I)(p<0.01, p<0.05). 3. When observing their surface structure, there were a lot of precipitate and pitting corrosion in the groups with welding(Group I & III), when the TiN-plated group(Group I) showed lower level than the TiN-nonplated group(Group IIII). On the other hand, the groups without welding(Group II & IV) indicated a little of pitting corrosion. 4. In case of observation with the naked eyes, it was shown that there were significant disco1oration and corrosion in the groups with welding(Group I & III), while there was no any remarkable change in the groups without welding(Group II & IV).

• The Korean Journal of Nuclear Medicine
• /
• v.2 no.1
• /
• pp.27-41
• /
• 1968

The ferrokinetics and red cell life spans of the patients with chronic glomerulonephritis were investigated by the double tracing method using radioactive iron ($^{59}Fe$) and chromium ($^{51}Cr$). According to the serum NPN levels, the patients were subdivided into 3 groups: Group 1. 6 patients, had the levels below 40 mg/dl Group 2. 6 patients, had the levels between 41 mg/dl to 80 mg/dl Group 3. 10 patients, had the levels above 80 mg/dl The results were as follows: 1) Red blood cell-, hematocrit- and hemoglobin values were moderately reduced in patients with normal serum NPN levels, while markedly reduced in patients with elevated serum NPN levels. 2) The plasma volume was increased, while the red cell volume was decreased in patients with elevated serum NPN levels, hence, total blood volume was unchanged. 3) The serum iron level was slightly reduced h patients of groups 1 and 2, while was within the normal ranges in patients of group 3. 4) i) In patients with normal serum NPN levels, the plasma iron disappearance rate, red cell iron utilization rate, red cell iron turnover rate, daily red cell iron renewal rate, circulating red cell iron and red cell iron concentration were within the normal ranges, while the plasma iron turnover rate was slightly reduced. ii) In patients with elevated serum NPN levels, the plasma iron disappearance rate was delayed, while the plasma iron turnover rate was within the normal ranges. The red cell iron utilization rate, red cell iron turnover rate and circulating red cell iron were decreased and the period in which the red cell iron utilization rate reachd its peak was delayed in Group 3 patients. The daily red cell iron renewal rate and the red cell iron concentration were unchanged. iii) The mean red cell life span was within the normal ranges in patients with normal serum NPN levels, while was shortened in patients with elevated serum NPN levels.

• Economic and Environmental Geology
• /
• v.45 no.2
• /
• pp.105-119
• /
• 2012

Indigenous bacteria isolated from contaminated sites play important roles to remediate contaminated groundwater. Chromium has the most stable oxidation states. Cr(VI) is toxic, carcinogenic, and mobile, but Cr(III) is less toxic and immobile. In this study, indigenous microorganism (MMPH-0) was enriched from Cr(VI) contaminated groundwater, and identified by 16S rRNA gene analysis. Using MMPH-0, the effect of stimulating with e-donors (glucose, lactate, acetate, and no e-donor control), respiration conditions, biomass, tolerance, and geochemical changes on Cr(VI) reduction were investigated in batch experiments for 4 weeks. The changes of Cr(VI) concentration and geochemical conditions were monitored using UV-vis-spectrophotometer and Eh-pH meter. And the morphological and chemical characteristics of MMPH-0 and precipitates in the effluents were characterized by TEM-EDS and SEM-EDS analyses. MMPH-0 (Enterobacter aerogenes) was able to tolerate up to 2000 mg/L Cr(VI) and reduce Cr(VI) under aerobic and anaerobic conditions. MMPH-0 performed faster and higher efficiency of Cr(VI) reduction with electron donors (over 70% after 1 week with e-donor, 10-20% after 4 weeks without e-donor). The changes of Eh-pH in effluents showing the tendency from oxidizing to reducing condition and a bit of acidic change in pH due to microbial oxidation of organic matters donating electrons and protons suggested the roles of MMPH-0 on Cr(VI) in the contaminated water catalyzing to transit geochemical stable zone for more stable $Cr(OH)_3$ or Cr(III) precipitates. TEM/SEM-EDS analyses of MMPH-0 and precipitates indicate direct and indirect Cr(VI) reduction: extracellular polymers capturing Cr component outside cells. These results suggested diverse indigenous bacteria and their biogeochemical reactions might enhance more effective and feasible remediation technology of redox sensitive heavy metals in metal-contaminated in groundwater.

• The Korean Journal of Nuclear Medicine
• /
• v.3 no.2
• /
• pp.1-16
• /
• 1969

The double tracer study on erythrokinetics was carried out experimentally with radioactive iron ($^{59}Fe$) and chromium ($^{51}Cr$) in rabbits. The 0.1% canthalidin solution and 1% pot. perchlomate solution was given subcutaneously to 20 rabbits respectively. 3 and 6 days after injection, the blood chemistry, urine examination, ferrokinetics and apparent half survival time of RBC were ($^{51}Cr\;T\frac{1}{2}$)determined. Following were the results: 1) Red blood cell hematocrit and hemoglobin values were moderately reduced and B.U.N. and serum creatinine values were slight]y inercased in the canthalidin group, while B.U.N. and serum creatinine values were within normal limits in the pot. perchlomate group. Reticulocyte values were slight]y increased in the canthalidin group, while was normal range in the pot. perchlomate group. 2) Blood chemistry finding was not significant statistically in both experimental groups, but serum iron value was moderately reduced in both group. 3) Plasma volume was unchanged in both group, but red cell volume and whole blood volume were slightly reduced in both groups. 4) Results of ferrokinetics were as follows: i) The plasma iron disappearance rate was delayed in both groups. Plasma iron turnover rate, red cell iron utilization and red cell iron turnover rate were decreased in both groups, and then red cell iron turnover rate was more decreased than plasma iron turnover rate in both groups. Circulating red cell iron was slight]y increased in canthalidin group and red cell iron concentration was within normal range in both groups. ii) P.I.T.R.-R.C.I.T. value was moderately increased in the canthalidin group and slightly increased in the pot. perchlomate group. Reticulocyte index, red cell iron turnover index, plasma iron turnover index and effective erythropoiesis index were whole]y reduced in both groups. iii) The red cell life span was slightly shortened in the canthalidin group while was within normal range in pot. perchlomate group. The pathologic finding of renal biopsy of the canthalidin group shows a selective damage in glomerulus, while shows almost normal range or slight damage in tubules. And that of the pot. perchlomate group shows a selective damage in tubules with slight damage of glomerulus.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.11
• /
• pp.484-488
• /
• 1997

Three-dimensional finite element analyses were used to compare the stress distribution and the stability of the fixation among seven different tibial components and to investigate the effect due to implant materials in total knee arthroplasty. The components included an intact tibia(Type I), Cemented Cobalt-Chromium tibial tray implanted with a PMMA cemented Co-Cr stem(Type II), Cemented Co-Cr tibial tray with a uncemented Co-Cr stem(Type III), Cemented Ultra High Molecular Weight Polyethylene (UHMWPE) tibial tray with a cemented UHMWPE stem (Type IV), Cemented UHMWPE tray with a uncemented UHMWPE stem(Type V), Cemented Co-Cr tray without a stem(Type VI), and Cemented UHMWPE tray without a stem(Type VII). Uncemented components were assumed to have complete bony in growth and a rigid state of fixation between component and bone. The interface between bone/cement/component of cemented components was also assumed to be fully bonded. Bi-condylar forces were applied. The results indicated that Uncemented stem components provided lower bone stress shielding and stress concentration. The UHMWPE tray and stem component showed better agreement with the intact tibia than the Co-Cr Alloy tray and stem components. If the implant tray can be fixed firmed without a stem, Cemented PE tray without a stem(Type VII) may be recommended to give the best characteristics in the sense of stress distribution and stability.

• Journal of Korean Society on Water Environment
• /
• v.20 no.6
• /
• pp.670-675
• /
• 2004

Humic acids are macromolecules originated from natural water, soil, and sediment. The characteristics of humic acid enable it to change the distribution of metals as well as many kinds of organic contaminants and to determine the sorption of them from soil solution. To see the effect of humic acid on the removal rate of organic contaminants and heavy metals, batch-scale experiments were performed. As a natural geosorbent, black shale was used as a sorbent media, which showed hight sorption capacity of trichloroethylene (TCE), lead, cadmium and chromium. The effect of sorption-desorption, pH, ionic strength and the concentration of humic acid was taken into consideration. TCE sorption capacity by black shale was compared to natural bentonite and hexadecyltrimethylammonium (HDTMA) modified bentonite. The removal rate was good and humic acid also sorbed onto black shale very well. The organic part of humic acid could effectively enhance the partition of TCE and it act as an electron donor to reduce Cr(VI) to Cr(III). Cationic metal of Pb(II) and Cd(II) also removed from the water by black shale. With 3 mg/L of humic acid, both Pb(II) and Cd(II) were removed more than without humic acid. That could be explained by sorption and complexation with humic acid and that was possible when humic acid could change the hydrophobicity and solubility of heavy metals. Humic acid exhibited desorption-resistivity with black shale, which implied that black shale could be an alternative sorbent or material for remediation of organic contaminants and heavy metals.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.5
• /
• pp.727-733
• /
• 2011

A new Korean standard for the determination of Cr(VI) in soils has been officially published as ES 07408.1 in 2009. This analytical method is based on the hot alkaline digestion and colorimetric detection prescribed by U.S. EPA method 3060A and 7196A. The hot alkaline digestion accomplished using 0.28 M $Na_2CO_3$ and 0.5 M NaOH solution (pH 13.4) at $90{\sim}95^{\circ}C$ determines total Cr(VI) in soils extracting all forms of Cr(VI), including water-soluble, adsorbed, precipitated, and mineral-bound chromates. This aggressive alkaline digestion, however, proved to be problematic for certain soils which contain large amounts of soluble humic substances or active manganese oxides. Cr(III) could be oxidized to Cr(VI) by manganese oxides during the strong alkaline extraction, resulting in overestimation (positive error) of Cr(VI). In contrast, Cr(VI) reduction by dissolved humic matter or Fe(II) could occur during the neutralization and acidic colorimetric detection procedure, resulting in underestimation (negative error) of Cr(VI). Futhermore, dissolved humic matter hampered the colorimetric detection of Cr(VI) using UV/Vis spectrophotometer due to the strong coloration of the filtrate, resulting in overestimation (positive error) of Cr(VI). Without understanding the mechanisms of Cr(VI) and Cr(III) transformation during the analysis it could be difficult to operate the experiment in laboratory and to evaluate the Cr(VI) results. For this reason, in this paper we described the theoretical principles and limitations of Cr(VI) analysis and provided useful guidelines for laboratory work and Cr(VI) data analysis.

• Analytical Science and Technology
• /
• v.24 no.4
• /
• pp.243-248
• /
• 2011

A selective determination method of mercury (II) ion in aqueous solution by luminol-based chemiluminescence system (luminol CL system) has been developed. Determination of metal ions such as copper (II), iron (III), chromium (III) ion in solution by the luminol CL system using its catalytic role in the reaction of luminol and hydrogen peroxide has been reported by several groups. In this study, the catalytic activity of mercury (II) ion in the reaction of luminol and hydrogen peroxide was observed by the enhanced CL intensity of the luminol CL system. Based on this phenomenon, experimental conditions of the luminol CL system were investigated and optimized to determine mercury (II) ion in aqueous solution. While mercury (II) ion in mixed sample solution containing mercury (I) and (II) ions highly enhanced the CL intensity of the luminol CL system, the mercury (I) ion could not enhanced the CL intensity. Thus selective determination of the mercury (II) ions in a mixture containing mercury (I) and (II) ions could be achieved. Each concentration of mercury (I) and (II) ions in aqueous solution can be obtained from the results of the CL method that give the concentration of only mercury (II) ion and the inductively coupled plasma (ICP) method that give the total concentration of mercury ions. On the optimized conditions, the calibration curve of mercury (II) ion was linear over the range from $1.25{\times}10^{-5}$ to $2.50{\times}10^{-3}M$ with correlation coefficient of 0.991. The detection limit of mercury (II) ion in aqueous solution was calculated to be $1.25{\times}10^{-7}M$.