• 전기전자학회논문지
• /
• 제24권4호
• /
• pp.1129-1135
• /
• 2020

배터리를 사용함에 따라 노화가 진행되면 배터리의 충전 가능 용량을 나타내는 State of Health(SoH)가 줄어들게 된다. 배터리 모니터링 시스템(BMS)에서 SoH를 추정하는 것이 매우 중요하며, 이를 위해 배터리 내부 저항을 측정하는 방법이 많이 사용된다. 일반적으로 배터리에 특정한 주파수의 전류원을 인가하고 전압응답을 측정하여 내부저항을 연산한다. 충전기가 동작할 경우 전압응답에 충전 고조파 잡음이 발생하여 저항 측정의 정확도가 떨어진다. 본 논문에서는 충전잡음의 영향을 제거하기 위하여 강인한 배터리 내부저항 측정 알고리즘을 제안하였다. 전류원 신호와 전압응답 신호를 일정한 주기 동안 적분하여 잡음을 제거하는 방법으로 우수한 정확도와 안정된 연산결과를 보였다. 무정전 전원장치용 BMS에 적용하여 제안한 방법의 유용함을 입증하였다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권4호
• /
• pp.265-271
• /
• 2000

A non-contact battery charger for cellular phone is designed using half-bridge series resonant converter. This converter utilizes series resonance to reduce the undesirable effect of large leakage inductance of the detachable transformer and ZVS operation can reduce switching loss and switching noise. In this paper, analysis and design procedure of half-bridge series resonant converter with detachable transformer is presented. The input voltage is 85VAC∼270VAC, and the output voltage and current is 4.1V and 800mA, respectively. Furthermore, a method of calculating the secondary current of the transformer to control the battery charging current in the constant current charging mode is proposed. The performance of the charger is verified through experiments.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.261-265
• /
• 2005

본 논문에서는 하이브리드 자동차용 보조전원 공급이 목적인 DC-DC Converter에 대하여 기술하였다. DC-DC Converter는 차량 내의 헤드램프, 오디오, 각종 ECU등 전기/전자 부하에 전력을 공급하며 또한 12V 보조 배터리를 충전하는데 사용된다. 고주파 동작 조건하에서 유기되는 전자파 노이즈와 스위칭 손실을 저감하기 위하여 컨버터 토폴로지로 위상천이 영전압 풀브리지 방식을 적용하였으며 제어기의 용이한 보상 및 안정된 시스템 응답 특성을 위하여 슬로프 보상이 포함된 전류 모드 제어방식을 사용하였다 정전압/정전류 충전 제어 방식은 전기부하에 안정적인 전원공급과 보조 배터리의 안정적인충전을 보장한다. 초기의 회로 파라메타 설정 및 하드웨어 디버깅을 위하여 시뮬레이션 툴로 PSIM 6.0을 사용하였으며. DC-DC Converter에서 스위칭 소자의 발열문제는 Thermo Tracer 장비를 사용하여 개선하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.435-438
• /
• 1998

In this paper, Electret is formed to range voltage -5[kV] to -8[kV] by corona charging in PTFE film and sensor is manufactured by method of moments in sensing infra sonic. Charges of charged film are calculated also TSC measurement and induced potential of sensing electrode according to the charges is become aware of computer simulation. Electret Infra Sonic Transducer, which is designed and manufactured according to the potential and electric field simulation in using method of moments, is proved as it is effectively. Because sensitivity that measured under 10[Hz] is that average value of sensitivity rising rate is 6.34 [dB/oct] as average value is $\pm$1 [dB/oct] range -5[kV] to -8[kV] in corona charging film. As a result, it is believed that characteristic of acquired transducer can be application of medical treatment, industry, and animal life researches and the study of noise elimination, what's more, is required.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제55권12호
• /
• pp.511-517
• /
• 2006

The key issues in high power, high energy applications such as electromagnetic launchers include safety, reliability, flexibility, efficiency, compactness, and cost. To explore some of the issues, a control scheme for a large current wave-forming was designed, built and experimentally verified using a 2.4MJ pulse power system (PPS). The PPS was made up of eight capacitors bank unit, each containing six capacitors connected in parallel. Therefore there were 48 capacitors in total, with ratings of 22kV and 50kJ each. Each unit is charged through a charging switch that is operated by air pressure. For discharging each unit has a triggered vacuum switch (TVS) with ratings of 200kA and 250kV. Hence, flexibility of a large current wave-forming can be obtained by controlling the charging voltage and the discharging times. The whole control system includes a personal computer(PC), RS232 and RS485 pseudo converter, electric/optical signal converters and eight 80C196KC micro-controller based capacitor-bank module(CBM) controllers. Hence, the PC based controller can set the capacitor charging voltages and the TVS trigger timings of each CBM controller for the current wave-forming. It also monitors and records the system status data. We illustrated that our control scheme was able to generate the large current pulse flexibly and safely by experiments. The our control scheme minimize the use of optical cables without reducing EMI noise immunity and reliability, this is resulting in cost reduction. Also, the reliability was increased by isolating ground doubly, it reduced drastically the interference of the large voltage pulse induced by the large current pulse. This paper contains the complete control scheme and details of each subsystem unit.

• 설비공학논문집
• /
• 제16권4호
• /
• pp.318-323
• /
• 2004

When a strong electric field is applied between a sharply curved electrode and a blunt surface, the corona may result in a gas movement in the electrode gap which is directed toward the blunt surface. That is called the corona wind. It enhances heat and mass transfer between the surface and the surrounding gas. Moreover such enhancement causes no noise or vibration, which can be applied in complex, isolated geometries, and allows simple control of surface temperatures. This paper examines the relationship between the corona wind and the relative humidity. The facility consists of high voltage power supply thin tungsten wire, plate electrode, multimeter, microammeter and flow meter. Gas velocity is a linear function of voltage, relative humidity and is proportional to the square root of the current. The maximum velocities for the positive and negative corona discharge are 1.9 m/s (2.74 CMM/m), 1.5 m/s(2.15 CMM/m), respectively.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.264-269
• /
• 1998

A proposed soft-switching buck-boost PWM converter has a lot of advantages, Viz., electric isolation, a high power factor, low switching losses, low EMI noise, reduction of the voltage and current stresses, etc. In a new PFC converter, the switching device is replaced by the loss-less snubber circuit to achieve the zero voltage switching (ZVS) at the maximum current. However, the charging current of the capacitor in the loss-less snubber circuit distorts the input current waveforms. To improve the input current waveform, a new duty factor control method is proposed in this paper.

• 한국소음진동공학회논문집
• /
• 제16권1호
• /
• pp.75-80
• /
• 2006

This paper introduces the mechanism of the ESD(electrostatic discharge) in the HDD spindle system using FDBs(fluid dynamic bearings). When a HDD(hard disk drive) spindle system is rotating, triboelectric charging occurs in the FDBs through the friction between the lubricant and the rotating shaft or between the lubricant and stationary sleeve. And this electrostatic charge is accumulated in the rotating parts of the HDD spindle system because they are insulated from the ground by the lubricant. This research shows experimentally that the behavior of electric charge and discharge in the FDB spindle system is the same as that of a capacitor. It also measures the electrostatic voltage difference between the rotating and stationary parts in the FDB spindle system due to the change of humidity, supporting load and motor speed. This research shows that the control of ESD is required in the HDD spindle system using FDBs, because the electrostatic charge accumulated in the FDB spindle system may cause the breakdown damage of the GMR head and data loss consequently.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.942-945
• /
• 2000

Recently, electret applications have placed the focus on polymer thin film because electrical properties of a blend are studied. In this paper, we hale measured the infra sonic frequency by using Electret Sensor. Electret is formed by appling the voltage range of -4[kV] to -8[kV] to PTFE film and the sensor is manufactured by moment method to detect the infra-sonic signal. Electret Infrasonic Transducer, which is designed and manufactured by using of the moment method according to the potential and electric field simulation , shows its promising result, since the average rising rate of sensitivity is 7.68 [dB/oct] under 1[Hz], and the average values are within ${\pm}$ 1 [dB/oct]. As a result, it is believed that the characteristics of acquired transducer can be applied to the medical treatment, the industry, and the animal life researches, and also the study on noise elimination is required.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.318-323
• /
• 2005

This paper introduces the mechanism of the ESD (Electrostatic discharge) in the HDD spindle system using FDBs (Fluid Dynamic Bearings). When a HDD (Hard Disk Drive) spindle system is rotating, triboelectric charging occurs in the FDBs through the friction of the lubricant between the rotating shaft and stationary sleeve. And this electrostatic charge is accumulated in the rotating part of the HDD spindle system because it is insulated from the ground by the lubricant. This research shows experimentally that the behavior of electric charge and discharge in the FDB spindle system is the same as that of a capacitor. It also measures the electrostatic charge and discharge of the FDB spindle system due to the chanse of humidity, supporting load and motor speed. This research shows that the control of ESD is required in the HDD spindle system using FDBs, because the electrostatic charge accumulated in the FDB spindle system may cause the breakdown damage of the GMR head and data loss consequently.