• 한국수자원학회논문집
• /
• 제37권8호
• /
• pp.623-630
• /
• 2004

본 논문에서는 수리모형 실험을 통하여 지류와 본류의 합류점의 접근각도, 본류의 유량 및 본류와 지류의 유량비 변화에 따른 합류부의 수리학적 특성을 파악하였다. 실험은 수로길이 450cm의 수로에서 실시하였으며, 본류와 지류의 수로폭은 각각 40cm와 32cm이었으며, 4조의 물탱크와 펌프가 설치되었다. 합류점 부근의 정체 구간의 길이는 접근각도가 증가함에 따라 증가되며, 본류의 유량과 지류와 본류와의 유량비가 증가되는 경우에도 이 경향은 동일하다. 그러나 동일한 합류점 접근각도와 유량비에 있어서 본류 유량 변화에 따른 합류점 부근의 정체구간 변화는 매우 적게 나타나고 있다. 또한 본류와 지류의 유량비가 증가할수록 유속의 정체 구간의 길이가 커져, 유사의 퇴적증가를 유도하는 주요원인이 된다. 합류점 부근의 가속유로는 접근각도가 작을수록 수로 내 중앙부에 한정되지만, 접근각도가 증가할수록 영향권이 증가된다.

• Nuclear Engineering and Technology
• /
• 제28권3호
• /
• pp.280-289
• /
• 1996

The pressure drop of twelve fuel bundle string in the CANDU-6 fuel channel is equal to the sum of the eleven junction pressure losses, the bundle string entrance and exit pressure losses, the skin friction pressure loss, and other appendage pressure losses, where the junction loss is dependent on the bundle end faces and angular alignments of the junctions. The results of the single junction pressure drop tests in a short rig show that the most probable pressure drop of the eleven junctions was analytically equal to the eleven times of average pressure drop of all the possible single junction pressure drops, and also that the largest and smallest junction pressure drops across the eleven junctions probably occurred only with BA and BB type junctions, respectively, where A and B denote the bundle end sides with an end-plates on which a company monogram is stamped and unstamped, respectively.

• 한국환경과학회지
• /
• 제16권4호
• /
• pp.495-503
• /
• 2007

In this study, we took the geometrical character of the river channel junction and hydrologic conditions as independent variables, and hydraulic behavior characteristics as an independent variable. The result, after multiple analysis was carried out, proved that, except for the generating area of the accelerating zone of velocity the accelerating zone and both the main channel and the tributary zone of stagnation the stagnation zone, there was correlation of over 90%. Also, derived presumed expression of the hydraulic characteristics of the junction was applied to the real natural channel - the river channel of the Guem-ho main channel(the A-yang bridge to the Guem-ho bridge). As the result, it proved that it represented hydraulic characteristics relatively well.

• 한국환경과학회지
• /
• 제17권7호
• /
• pp.783-793
• /
• 2008

The purpose of this study is to analyze the sensitivity of the RMA2 model parameters reflecting the flow characteristics of stream junction and thus understand the hydraulic characteristics of the channel confluence flow. This study dealt with the input parameters of the RMA-2 model, a two-dimensional numerical analysis model widely used for researches both at home and abroad. The parameters of the RMA-2 model are roughness coefficient, turbulent diffusion coefficient, Coriolis forces latitude, Density, and mesh size. This study those parameters estimated from actual heavy rainfall, and varied the parameter size by (-)30%${\sim}$+30% to review the characteristics of the flow characteristics of the channel section. Weobserved that when the ratio of the channel width was relatively small, the smaller the approaching angle was, the farther from the junctions became the generating place of the maximum flow velocity, however, when the ratio of the channel width was relatively large, the larger the approaching angle was, the farther the generating place of the maximum flow velocity from the junctions became. In particular, the distance between junctions and the place where the maximum flow velocity generated showed an absolute correlationover 90% of the relative channel width, but an inverse relationwas found when the distance to the place where the flow velocity generated was shortened as relative the channel width between the main channel and tributary increased.

• 한국산업융합학회 논문집
• /
• 제10권4호
• /
• pp.275-283
• /
• 2007

This study aims at the calculation of a variation of flow characteristics of main channel for tributary inflow in river junction. So this study was analyzed the variation of flow depth and velocity in main channel for a change of inflow degree. For this purpose, FLDWAV model are carried out for variations of $30^{\circ}$, $60^{\circ}$ and $90^{\circ}$ tributary inflow at junction. Results show that velocity ratio(V1/V3) increases and flow depth ratio(H1/H3) decreases for discharge ratio(Q1/Q3) of upstream and downstream when degree increases in junction. And FLDWAV model was applied at a real river junctions. Selected area is a junction of Gumho river and Sin stream. Results show that pattern is similar to a virtual channel.

• EDISON SW 활용 경진대회 논문집
• /
• 제2회(2013년)
• /
• pp.266-268
• /
• 2013

In this paper, we study the channel doping concentration characteristics of junctionless nanowire transistors (JLT) using Edison nanowire FET device simulation. JLT has no junctions by very simple fabrication process. And this device has less variability and better electrical properties than classical inversion-mode transistors with PN junctions at the source and drain. In this simulation we use tri-gate structure. Source and drain doping concentration is $10^{20}atoms/cm^3$. The simulation results show that I-V characteristics of JLT change due to the variation of channel doping concentration.

• 설비공학논문집
• /
• 제27권11호
• /
• pp.559-566
• /
• 2015

The main objective of this work is to experimentally investigate the effect of angle variation on the distribution of two-phase flow at header-channel junctions. The cross-sections of the header and the channels were fixed at $16mm{\times}16mm$ and $12mm{\times}1.8mm$, respectively. Air and water were used as the test fluids. Four different header-channel positions were tested : Vertical header with Horizontal channels (case VM-HC), Horizontal header with Horizontal channels (case HM-HC), Horizontal header with Vertical Downward channels (case HM-VDC), and Horizontal header with Vertical Upward channels (case HM-VUC). In all cases, liquid flow distribution tended to decrease gradually in the upstream header region. However, in the downstream region, different trends could be seen. The reason for these different tendencies were identified by flow visualization in each case. The standard deviations for the liquid and gas flow distribution in each case were calculated, and the case of VM-HC had the lowest values compared to other cases because of the symmetrically distributed liquid film and strong flow recirculation near the end plate.

• The Korean Journal of Physiology and Pharmacology
• /
• 제5권1호
• /
• pp.1-8
• /
• 2001

Hyperpolarization of arterial smooth muscle by acetylcholine is considered to be produced by the release of an unidentified chemical substance, an endothelium-derived hyperpolarizing factor (EDHF). Several chemicals have been proposed as the candidate for EDHF. However, none of them fulfil completely the nature and property of EDHF. Ultrastructural observation with electron microscope reveals that in some arteries, gap junctions are formed between endothelial and smooth muscle cells. In small arterioles, injection of gap junction permeable dyes into an endothelial cell results in a distribution of the dye to surrounding cells including smooth muscle cells. These observations allow the speculation that myoendothelial gap junctions may have a functional significance. Simultaneous measurement of the electrical responses in both endothelial and smooth muscle cells using the double patch clamp method demonstrates that these two cell types are indeed electrically coupled, indicating that they behave as a functional syncytium. The EDHF-induced hyperpolarization is produced by an activation of $Ca^{2+}-sensitive\;K^+-channels$ that are inhibited by charybdotoxin and apamin. Agonists that release EDHF increase $[Ca^{2+}]_i$ in endothelial cells but not in smooth muscle cells. Inhibition of gap junctions with chemical agents abolishes the agonist-induced hyperpolarization in smooth muscle cells but not in endothelial cells. All these observations can be explained if EDHF is an electrotonic signal propagating from endothelium to smooth muscle cells through gap junctions.

• Steel and Composite Structures
• /
• 제5권2_3호
• /
• pp.235-246
• /
• 2005

Local buckling is a major consideration in the design of thin-walled cold-formed steel sections. The main effect of local buckling in plate elements under longitudinal compressive stresses is to cause a redistribution of the stresses in which the greatest portion of the load is carried near the supporting edges of the plate junctions. The redistribution produces increased stresses near the plate junctions and high bending stresses as a result of plate flexure, leading to ultimate loads below the squash load of the section. In singly symmetric cross-sections, the redistribution of longitudinal stress caused by local buckling also produces a shift of the line of action of internal force (shift of effective centroid). The fundamentally different effects of local buckling on the behaviour of pin-ended and fixed-ended singly symmetric columns lead to inconsistencies in traditional design approaches. The paper describes local buckling and shift of effective centroid of thin-walled cold-formed steel channel columns. Tests of channel columns have been described. The experimental local buckling loads were compared with the theoretical local buckling loads obtained using an elastic finite strip buckling analysis. The shift of the effective centroid was also compared with the shift predicted using the Australian/New Zealand and American specifications for cold-formed steel structures.

• 한국수자원학회논문집
• /
• 제37권10호
• /
• pp.881-888
• /
• 2004

본 연구에서는 지류와 본류의 합류부의 접근각도, 상류부 유량 및 본류와 지류의 유량비 변화에 따른 수리 모형실험을 통한 합류부의 수리학적 특성을 파악하였다. 합류부의 수리학적 특성은 합류점 부근의 유속과 관련된 최대유속의 크기 및 발생위치를 분석하였다. 합류점 부근의 최대유속은 접근각도가 증가함에 따라 점차 증가하며, 이는 유량 및 유량비가 증가하는 경우에도 동일한 경향을 나타낸다. 합류점 부근의 최대유속의 발생지점은 접근각도가 증가함에 따라 거리가 증대되는 것으로 나타났다. 또한, 유량이 증가하는 경우에도 거의 동일한 양상을 보여준다.