• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.627-630
• /
• 2003

This work presents a numerical procedure to optimize the shape of three-dimensional channel with angled ribs mounted on one of the walls to enhance turbulent heat transfer. The response surface method is used as an optimization technique with Reynolds-averaged Navier-Stokes analysis of flow and heat transfer. SST turbulence model is used as a turbulence closure. The width-to-height ratio of the rib, rib height-to-channel height ratio, pitch-to-rib height ratio and attack angle of the rib are chosen as design variables. The objective function is defined as a linear combination of heat-transfer and friction-loss related terms with weighting factor. D-optimal experimental design method is used to determine the data points. Optimum shapes of the channel have been obtained for the weighting factors in the range from 0.0 to 1.0.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.2
• /
• pp.260-264
• /
• 2017

Process variation effect on arch-structured gate stacked array (GSTAR) 3-D NAND flash is investigated. In case of arch-structured GSTAR, a shape of the arch channel is depending on an alignment of photo-lithography. Channel width fluctuates according to the channel hole alignment. When a shape of channel exceeds semicircle, channel width becomes longer, increasing drain current. However, electric field concentration on tunnel oxide decreases because less electric flux converges into a larger surface of tunnel oxide. Therefore, program efficiency is dependent on the process variation. Meanwhile, a radius of channel holes near the bottom side become smaller due to an etch slope. It also affects program efficiency as well as channel width. Larger hole radius has an advantage of higher drain current, but causes degradation of program speed.

• Design & Manufacturing
• /
• v.16 no.3
• /
• pp.58-65
• /
• 2022

Micro-fluidic chip has been fabricated by lithography process on silicon or glass wafer, casting using PDMS, injection molding of thermoplastics or 3D printing, etc. Among these processes, 3D printing can fabricate micro-fluidic chip directly from the design without master or template for fluidic channel fabricated previously. Due to this direct printing, 3D printing provides very fast and economical method for prototyping micro-fluidic chip comparing to conventional fabrication process such as lithography, PDMS casting or injection molding. Although 3D printing is now used more extensively due to this fast and cheap process done automatically by single printing machine, there are some issues on accuracy or surface characteristics, etc. The accuracy of the shape and size of the micro-channel is limited by the resolution of the printing and printing direction or layering direction in case of SLM type of 3D printing using UV curable resin. In this study, the printing direction and thickness of each printing layer are investigated to see the effect on the size, shape and surface of the micro-channel. A set of micro-channels with different size was designed and arrayed orthogonal. Micro-fluidic chips are 3D printed in different directions to the micro-channel, orthogonal, parallel, or skewed. The shape of the cross-section of the micro-channel and the surface of the micro-channel are photographed using optical microscopy. From a series of experiments, an optimal printing direction and process conditions are investigated for 3D printing of micro-fluidic chip.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.61 no.4
• /
• pp.33-42
• /
• 2019

In this study, the channel and floodplain widths are indirectly measured for three different watersheds using satellite images to reflect the shape of Korean channels in the Soil and Water Assessment Tool (SWAT) model. For measuring the channel and floodplain widths, multiple satellite images were referred to ensure the widest width of certain points. In the single channel, the widths at the multiple points were measured. Based on the measured data, the regression equations were derived to estimate the channel and floodplain widths according to watershed areas. Applying these developed equations, this study evaluated the effect of the change of channel and floodplain widths on the SWAT simulation by comparing to the measured streamflow data. The developed equations estimated larger channel width and smaller floodplain compared with those calculated in the current SWAT model. As shown in the results, there was no considerable changes in the predicted streamflow using the current and developed equations. However, the flow velocity and channel depth calculated from the developed equations were smaller than those of the current equations. The differences were caused by the effect of different channel geometries used for calculating the hydraulic characteristics. The channel geometries also affected the water quality simulation in channels because the hydraulic characteristics calculated by the channel geometries are directly related to the water quality simulation. Therefore, application of the river cross-sectional regression equation reflecting the domestic stream shape is necessary for accurate water quantity / quality and water ecosystem simulation using hydrological model.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.5
• /
• pp.19-26
• /
• 2014

The cross flow turbine attracts more and more attention for its relatively wide operating range and simple structure. In this study, a novel type of micro cross flow turbine is developed for application to a step in an irrigational channel. The head of the turbine is only H=4.3m and the turbine inlet channel is open ducted type, which has barely been studied. The efficiency of the turbine with inlet open duct channel is relatively low. Therefore, a guide nozzle on the turbine inlet is attached to improve the performance of the turbine. The guide nozzle shapes are investigated to find the best shape for the turbine. The guide nozzle plays an important role on directing flow at the runner entry, and it also decreases the negative torque loss by reducing the pressure difference in Region 1. There is 12.5% of efficiency improvement by attaching a well shaped guide nozzle on the turbine inlet.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.2 s.41
• /
• pp.7-15
• /
• 2007

A numerical procedure for optimizing the shape of three-dimensional channel with V-shaped ribs extruded on both walls has been carried out to enhance the turbulent heat transfer. The response surface based optimization is used as an optimization technique with Reynolds-averaged Wavier-stoked analysis. Shear stress transport (SST) turbulence model is used as a turbulence closure. Computational results for average heat transfer rate show good agreements with experimental data. The objective function is defined as a linear combination of heat transfer and friction loss-related terms with a weighting factor. Three dimensionless variables such as, rib pitch-to-rib height ratio, rib height-to-channel height ratio, and the attack angle of the rib are chosen as design variables. Nineteen training points obtained by D-optimal designs for three design variables construct a reliable response surface. In the sensitivity analysis, it is found that the objective function is most sensitive to the ratio of rib height-to-channel height ratio. And, optimal values of design variables have been obtained in a range of the weighting factor.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.1
• /
• pp.52-60
• /
• 2008

Staggered dimples printed on opposite walls of an internal cooling channel are formulated numerically and optimized to enhance heat transfer performance. Nusselt number and friction factor based objectives are considered and a weighted average surrogate model is used to approximate the data generated by numerical simulation. The dimpled channel shape is defined by three geometric design variables, and the design point within design space are selected using Latin hypercube sampling. A weighted-sum method for multi-objective optimization is applied to integrate multiple objectives into a single objective. By the optimization, the objective function value is improved largely and heat transfer rate is increase much higher than pressure loss increase due to shape deformation. Channel with vertically non-symmetric optimum dimples is tested and found that the best appears if dimples on opposite wall are displaced by one quarter of dimple spacing.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.1
• /
• pp.80-93
• /
• 1997

This paper proposes a new technique of optimal codebook design in multistage gain-shape vector quantization (MS-GS VQ) for wireless image communication. An original image is divided into a smany blocks as possible in order to get strong robustness to channel transmission errors: the original image is decomposed into a number of subband images, each of which contains a sperate spatial frequency information and is obtained by the biorthogonal wavlet transform; each subband is separated into several consecutive VQ stages, where each stage has a residual information of the previous stage; one vector in each stage is divided into two components-gain and shape. But, this decomposition genrates too many blocks and it thus makes the determination of optimal codebooks difficult. We overcome this difficulty by evolving each block's codebook independently with different genetic algorithm that uses each stage's individual training vectors. Th eimpact of th eproposed VQ technique on the channel transmission errors is compared with that of other VQ techniques. Simulation results show that the proposed VQ technique (MS-GS VQ) with the optimal codebook designe dy genetic algorithms is very robust to channel transmission errors even under the bursty and high BER conditions.

• ETRI Journal
• /
• v.27 no.2
• /
• pp.153-165
• /
• 2005

The main purpose of a spatial audio system is to give a listener the same impression as if he/she were present in a recorded environment. A dummy head microphone is generally used for such purposes. Because of its human-like shape, we can obtain good spatial sound images. However, its shape is a restriction on its public use and it is difficult to convert a 2-channel recording into multi-channel signals for an efficient rendering over a multi-speaker arrangement. In order to solve the problems mentioned above, a spatial audio system is proposed that uses multiple microphones on a rigid sphere. The system has five microphones placed on special points of the rigid sphere, and it generates audio signals for headphone, stereo, stereo dipole, 4-channel, and 5-channel reproduction environments. Subjective localization experiments show that front/back confusion, which is a common limitation of spatial audio systems using the dummy head microphone, can be reduced dramatically in 4-channel and 5-channel reproduction environments and can be reduced slightly in a headphone reproduction.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.7 s.250
• /
• pp.700-706
• /
• 2006

This study presents a numerical procedure to optimize the shape of dimple surface to enhance turbulent heat transfer in a rectangular channel. The response surface based optimization method is used as an optimization technique with Reynolds-averaged Wavier-Stokes analysis of fluid flow and heat transfer with shear stress transport (SST) turbulence model. The dimple depth-to-dimple print diameter ratio, channel height-to-dimple print diameter ratio, and dimple print diameter-to-pitch ratio are chosen as design variables. The objective function is defined as a linear combination of heat transfer related term and friction loss related term with a weighting factor. full factorial method is used to determine the training points as a mean of design of experiment. The optimum shape shows remarkable performance in comparison with a reference shape.