• Journal of Korea Water Resources Association
• /
• v.37 no.8
• /
• pp.623-630
• /
• 2004

In this paper, the hydraulic model tests are conducted for the hydraulic characteristics at channel junctions. The experiments are examined through the variation of approaching angle, discharge in the upstream main channel and the discharge ratio between the main channel and the tributary. The experiments are conducted in the channel model having the length of 450cm, the widths of 40cm and 32cm. Four water tanks and pumps are installed in the experimental channel. The length of stagnation zone is increased by Increasing of approaching angle and the discharge in the upstream channel. The length of stagnation increase with the discharge ratio between the main channel and the tributary. However, the variation of the stagnation zone near the channel junctions is little at the same approaching angles and the discharge ratioes between the main channel and tributary. However, the variation of the stagnation zone near the channel junctions is little at the same approaching angles and the discharge ratioes between the main channel and tributary. Accelerating zone of the velocity is occurred in the middle of the channel in the small approaching angle. However, the influence zone of the accelerating velocity is increased by increasing the approaching angle.

• Journal of Korea Water Resources Association
• /
• v.37 no.10
• /
• pp.881-888
• /
• 2004

In this study, the hydraulic characteristics at junction are studied through the variation of approaching angle, discharge in the upstream channel and the discharge ratio between the main channel and the tributary. The maximum velocity as well as the position of the maximum velocity is included in the hydraulic characteristics. The maximum velocity is increased by increasing of approaching angle, discharge in the upstream channel and the discharge ratio between the main channel and the tributary. The length from the channel junction to the point of maximum velocity is increasing by increasing of approaching angle, discharge in the upstream channel and the discharge ratio between the main channel and the tributary.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.3 s.106
• /
• pp.267-271
• /
• 2006

In this paper, we use the OFDM transmission channel model applied to the MIMO antennas considering spatial propagation property to evaluate and investigate the ergodic capacity of the channel. Specially, we have applied our results to 3GPP TR 25.99 V1.1.0 case 1 LOS off channel description and calculated ergodic capacity with parameters, cluster angle spread and angle of arrival(AOA). Our results show that as the cluster angle spread increase the channel capacity increase until 35 degree, but for more than 35 degree channel capacity does not improved.

• Journal of the Korean Society of Safety
• /
• v.16 no.3
• /
• pp.12-18
• /
• 2001

The objective of the present work is to examine the effect of inclined angle of channel with multi heat source on thermal stability of electronic equipment. The heat sources are mounted on both sides of channel walls by two kinds of configuration such as the zig-zag md symmetric on. Conductive heat transfer was estimated by using of thermocouples and heat flux sensor. Thus, convective heat transfer and mean Nusselt number could be obtained. With increased inclined angle, the convective heat transfer coefficient was decreased. When inclined angle was smaller than 30 degree, The average Nusselt number of Big-zag configuration was larger than that of symmetric. Furthermore, when protruding ration was 0.082, the temperature was strongly affected by inclined angle. whereas, when protruding ration was 0.25, the temperature was strongly affected by heat source configuration.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.3
• /
• pp.1363-1370
• /
• 2018

In visible light (VL) positioning based on angle of arrival (AOA) estimation for smart indoor service, the AOA parameters obtained at the receiver has sometimes a random and distributed angle form instead of a point angle form due to the multipath transfer of the actual visible light and short positioning distance. The AOA estimation of a VL signal with a random and parametric distributed angle form may give incorrect AOA parameter estimates, which may result in poor VL positioning performance. In this paper, we classify the AOA parameters of the received VL signal into three forms according to the actual positioning channel environment and consider the short-range VL positioning method. We propose a subspace-based AOA parameter estimation technique and a data fusion method, and analyzed the proposed method by simulation and the measurement of the real VL channel characteristics.

• Journal of applied mathematics & informatics
• /
• v.41 no.1
• /
• pp.51-70
• /
• 2023

The flow of an incompressible Ellis fluid in an inclined asymmetric channel, driven by peristaltic waves was studied under low Reynolds number and long wavelength assumptions. The wave on each side of the channel are assumed to be an infinite train of sinusoidal waves, both having the same constant wave speed and wavelength however, they vary in wave amplitude, channel half width and phase angle. We derived expressions for the axial and transverse velocities, volume flow rate, pressure rise per unit wavelength and streamlines. The effects of varying the wave amplitudes, the phase angle, the channel width, the angle of inclination of the channel as well as the fluid parameters on the flow were analyzed. Trapping conditions were determined and the presence of reflux highlighted using the streamlines for the necessary channel and fluid conditions. By varying the fluid parameters, changes in the fluid that deviated from the Newtonian case resulted in a reduction in the axial velocity in the neighborhood of the center of the channel and a simultaneous increase in the velocity at the periphery of the channel. A nonlinear relation was observed with the pressure rise and the volume flow rate. This nonlinear relation is more pronounced with an increase in the absolute value of the volume flow rate. For Newtonian fluids a linear relation exists between these two variables. The fluid parameters had little effects on the streamlines. However, variations of the wave amplitudes, volume flow, channel width and phase angle had greater effects on the streamlines and hence the trapped region.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.471-476
• /
• 2001

The characteristics of conjugated heat transfer in the inclined channel was experimentally investigated. The simulated module is attached to the bottom of the inclined channel and is heated with constant heat flux. The experimental parameters of this study are input power (Q = 3, 7W), inlet air velocity ($V_{i}=0.1{\sim}0.9m/s$) and inclined channel angle (${\varphi}=0{\sim}90^{\circ}$). The results show that input power was most effective parameter on the temperature differences between module and air. As the inclined channel angle increases, the temperatures of the module are increased. And we obtained the best condition on the conductive board when ${\varphi}=0^{\circ}$.

• Journal of the Korean Society of Visualization
• /
• v.5 no.1
• /
• pp.37-42
• /
• 2007

Reverse flow occurs in a channel when there is an obstruction at the entry. However it has been shown recently that reverse flow can be realized without an obstruction, by staggering the sides of the channel and placing it at an angle of attack to the oncoming flow. In this study the latter flow is computationally investigated. Studies have been carried out for different widths (gap between the two walls forming the channel), and at an angle of attack of 30. The results have captured all the essential features of this complex phenomenon and show the time dependent pumping mechanism which leads to the occurrence of reverse flow.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.159-164
• /
• 2009

The water droplet motion and the interaction between the droplets in a PEMFC air flow channel with multiple pores, through which water emerges, is studied numerically by solving the equations governing the conservation of mass and momentum. The liquid-gas interface is tracked by a level set method which is based on a sharp-interface representation for accurately imposing the matching conditions at the interface. The method is modified to implement the contact angle conditions on the walls and pores. The dynamic interaction between the droplets growing on multiple pores while keeping the total water flow rate through pores constant is investigated by conducting the computations until the droplet motion exhibits a periodic pattern. The numerical results show that the droplet merging caused by increasing the number of pores is not effective for water removal and that the contact angle of channel wall strongly affects water management in the PEMFC air flow channel.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.21-27
• /
• 2010

The flow characteristics on a supersonic inlet with bleeding system by changing angles of attack and channel length conditions are studied by computational 3D turbulent flow analysis. A compressible upwind flux difference splitting Navier-Stokes method with $k-{\omega}$ turbulence model is used to analysis the inlet flowfield. More non-uniform flowfields are shown at the AIP when angle of attack becomes bigger and bigger. These non-uniform flowfield works the performance aggravating factors of the supersonic engine. Non-uniform flowfield by changing channel length at the various angle of attack are investigated.