• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.10
• /
• pp.2611-2623
• /
• 1993

To construct the design back data for a lean-burn gas engine, we investigated the combustion characteristics in the main chamber using a constant volume combustion chamber with subchamber. The combustion characteristics with configuration change of the critical passageholes have been studied by taking pressure data, schlieren photograph, ion current and light emission signal of flame. Heat release rate with various critical passageholes also have been analysed by using the combustion model of a prechamber diesel engine. It was found that combustion characteristics in the main combustion chamber were greatly influenced by the geometric configurations of critical passagehole.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.1
• /
• pp.141-148
• /
• 2008

This study was conducted to evaluate the effect of PAC(Powder Activated Carbon) retention time on stable operation of high concentration powered activated carbon(HCPAC-MBR) in the treatment of secondary domestic wastewater. The pilot scale HCPAC-MBR system was operated at two different SRTs, 25 days and 100 days. The main drawback of HCPAC-MBR system was the rapid increase of trans-membrane pressure. The increase rate of trans-membrane pressure was proportional to SRT value at constant flux. This result seemed to be caused by reduced amount of EPS adsorbed on the PAC in the reactor by decreasing the SRT of the PAC. The particle size of the PAC was also influenced by SRT. The PAC size was decreased as SRT was increased. The change of particle size could be one reason for the change of trans-membrane pressure. The pore volume in the cake-layer formed on the membrane surface became to be increased by reducing SRT, because the cake-layer was highly composed of the PAC. Therefore, increased pore volume might play a role to reduce the trans-membrane pressure. The removal rate of E260 and TOC was also inversely proportional to SRT value.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.655-662
• /
• 2003

Slope stability is an important issue ill civil engineering works or in open pit mines where both economy and efficiency is required. These are the long-term stability problems which depend on the change of physical properties under a certain weather condition. These can also result in progress of weathering which can change mechanical or hydro-geological properties of rock mass considerably. In this study, weathering in nature was simulated by freeze-thaw test and Soxhlet test which represent mechanical and chemical weathering respectively. Measured were elastic wave velocities, absorption rate, volume change. Uniaxial compression strengths before and after the weathering tests were also measured. The change in weight and volume of the specimens were not clearly related to the weathering process, but P, S wave velocities were clearly decreased as weathering progresses. For some class of rocks, P-wave velocity was increased probably because of the saturation due to improved connectivity of the pre-existing pores. Based on the test results, stability of the slopes were analyzed using FLAC$\^$2D/. Due to the reduced strength parameters, the factors of safety were decreased for the selected sites.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.22 no.2
• /
• pp.155-163
• /
• 2000

Osteoporosis is the consequence of an imbalance between osteoclastic and osteoblastic activity, coupled with an increased rate of bone turnover observed with menopause. Estrogen is generally considered to maintain bone mass through suppression of bone resorption. The purpose of this study was to evaluate the rat femoral trabecular change not only in the deficiency of estrogen but also in the administration of estrogen following ovariectomy(OVX). 30 female Sprague-Dawley rats were subjected to bilateral OVX or sham surgery(control). Groups of OVX were divided into 4 groups. The first group was injected daily with vehicle alone for 20 days after 20 weeks following OVX. The additional groups of OVX was injected daily with low, medium, or high doses of $17{\beta}-estradiol$(10, 25 or $50{\mu}g/kg$ BW, respectively). All rats were sacrified 23 weeks after OVX, and their femur were processed for H&E, MT stain and histomorphometry. The results were as follows; 1. In the histomorphometric analysis, the trabecular bone volume/tissue volume, trabecular thickness and trabecular seperation were respectively $31.2{\pm}8.3%$, $54.3{\pm}4.8{\mu}m$ and $280.7{\pm}16.4{\mu}m$ in vehicle treated OVX group and $48.6{\pm}7.3%$, $90.4{\pm}4.5{\mu}m$ and $126.3{\pm}5{\mu}m$ in sham operation group, and they showed statistical significance compare to control group. 2. The trabecular bone volume/tissue volume, trabecular thickness and trabecular separation were respectively $44.4{\pm}4.3%$, $109.5{\pm}12.3{\mu}m$ and $94.9{\pm}8.5{\mu}m$ in low doses of $17{\beta}-estradiol$ injected group and they showed statistical significance compare to OVX group. 3. The trabecular bone volume/tissue volume, trabecular thickness and trabecular separation were respectively $44.4{\pm}4.3%$, $109.5{\pm}12.3{\mu}m$ and $94.9{\pm}8.5{\mu}m$ in medium doses of $17{\beta}-estradiol$ injected group and they showed statistical significance compare to OVX group, but they didn't show statistical significance compare to low doses of $17{\beta}-estradiol$ injected group. 4. The trabecular bone volume/tissue volume, trabecular thickness and trabecular separation were respectively $46.4{\pm}4.5%$, $154.4{\pm}13.2{\mu}m$ and $113.7{\pm}12.8{\mu}m$ in high doses of $17{\beta}-estradiol$ injected group and they also showed statistical significance compare to OVX group, but they didn't show statistical significance compare to other experimental groups. From the above results, metaphyseal bone formation was markedly reduced in OVX rate but treatment of OVX rats with $17{\beta}-estradiol$ resulted in normalization of femur trabecular bone volume. But they didn't show statistical significance the effect of bone formation according to the dose dependency.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.12
• /
• pp.1933-1943
• /
• 2001

A micromechanical model is presented for superplasticity in which heterogeneous microstructures are coupled with deformation behavior. The effects of initial distributions of grain size, and their evolutions on the mechanical properties can be predicted by the model. Alternative stress rate models such as Jaumann rate and rotation incremental rate have been employed to analyze uniaxial loading and simple shear problems and the appropriate modeling was studied on the basis of hypoelasticity and elasto-viscoplasticity. The model has been implemented into finite element software so that full process simulation can be carried out. Tests have been conducted on Ti-6Al-4V alloy and the microstructural features such as grain size, distributions of grain size, and volume fraction of each phase were examined for the materials that were tested at different strain rates. The experimentally observed stress-strain behavior on a range of initial grain size distributions has been shown to be correctly predicted. In addition, the effect of volume fraction of the phases and concurrent grain growth were analyzed. The dependence of failure strain on strain rate has been explained in terms of the change in mechanism of grain growth that occurs with changing strain rate.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.11
• /
• pp.1486-1496
• /
• 2000

The initial flame kernel development and flame propagation in a constant volume combustion chamber is analyzed by the heat release rate and the mass fraction burnt. The combustion pressure is measured with a piezoelectric type pressure sensor. In order to evaluate the effects of ignition system and ignition energy on the flame propagation, four different ignition systems are designed and tested, and the ignition energy is varied by the dwell time. Several different spark plugs are also tested and examined to analysis the effects of electrodes on flame kernel development. The results show that the when the dwell time is increased, and when the spark plug gap is extended, heat release rate and the mass burnt fraction are increased. The materials and shapes of electrodes affect the flame development, because they change the energy transfer efficiency from electrical energy to chemical energy. The diameter of electrodes influences not only the heat release rate but also the mass burnt fraction as well.

• Laser Solutions
• /
• v.18 no.4
• /
• pp.17-22
• /
• 2015

In this paper, ablation rate of $Al_2O_3$ ceramics by femtosecond laser fluence is derived with experimental method. The automatic three axis linear stage makes laser optics to move with high spatial resolution. With 10 times objective lens, minimal pattern width of $Al_2O_3$ is measured in the focal plane. Ablated surface area is shown as linear tendency increasing number of machining times with various laser power conditions. Machining times is most sensitive condition to control $Al_2O_3$ pattern width. Also, the linear increment of pattern width with laser power change is investigated. In high machining speed, the ablation volume rate is more linear with fluence because pulse overlap is minimized in this condition. Thermal effect to surrounding medium can be minimized and clean laser process without melting zone is possible in high machining speed. Ablation volume rate decelerates as increasing machining times and multiple machining times should be considered to achieve proper ablation width and depth.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.8 no.1
• /
• pp.27-32
• /
• 1997

Recently, many people suffering from voice color change visit otolaryngologist. There is no specific data which can be evaluated objectively for voice color change in korean. In aerodynamic study, maximum phonation time, mean air flow rate, phonatory flow volume and subglottal pressure were tested by using Aerophone II voice function analyzer in korean. 112 male and 122 female aged from 10 to 69 years were randomly selected. Maximum phonation time was 20.8${\pm}$6.4sec in male and 17.2${\pm}$4.1sec in female. Mean air flow rate was 167.1${\pm}$61.4ml/sec. in male and 129.6${\pm}$49.3ml/sec in female. Phonatory flow volume was 3184.5${\pm}$646.0ml in male and 2122.1${\pm}$670.5ml in female. Subglottal pressure was 4.1${\pm}$1.8 cmH2O in male and 3.5${\pm}$1.4cm $H_2O$ in female. There was no statistically significant difference among age groups in all above results.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.7
• /
• pp.113-120
• /
• 2021

An experimental device was designed to control the opening of a damper via operating the folding blade drive of the device and to control the amount of air flowing through the damper. In addition, an inverter was installed in the blower to control its fan rotation speed and hence the amount of air flowing through the damper. An experimental study was conducted on the opening of the folding blade damper and changes in the rotational speed of the blower. From the results, the theoretical air volume of the folding blade damper and experimental air volume were observed to be in good agreement within an error range of ±3%. As the mass flow rate of the air passing through the folding blade damper increases proportionally with the changes in damper opening and fan rotation speed, the performance of the damper can be controlled proportionally. The mass flow rate was also observed to increase linearly; therefore, the mass flow rate of the air passing through the folding blade damper increases proportionally with changes in the rotation speed of the blower, such that the performance of the damper is proportional to a constant air volume even with varying rotation speeds of the blower.

• Korean Journal of Optics and Photonics
• /
• v.24 no.2
• /
• pp.71-76
• /
• 2013

Using fluorescence correlation spectroscopy, we analyzed the change of effective focal volume of a confocal system with light intensity. The fluorescence correlation spectroscopy system was home-built in accordance with the He-Ne laser with a wavelength of 632.8 nm, and two kinds of samples (AlexaFluor657 and Quantum dot655) suitable for the wavelength of the laser beam were used. For each sample, we analyzed and compared the correlation functions obtained while changing the intensity of the light source in a range of 1~50 ${\mu}W$. The result shows that the radius of the focal area increases linearly through the increase of particle number and diffusion time in response to an intensity change in weak light below 10 ${\mu}W$. In the higher intensity region (>10~15 ${\mu}W$), the increasing rate of particle number and diffusion time keep increasing but at a much slower rate. Through this result, it was also found that the radius increasing rate of the focal area was reduced however, the radius still increased slightly.