• Journal of the Korean Ceramic Society
• /
• v.43 no.10 s.293
• /
• pp.640-645
• /
• 2006

Monoclinic zirconia and yttria were mixed with a stoichiometric composition of 3Y-TZP (3 mol% Yttria-stabilized Tetragonal Zirconia Polycrystal). The specimen was sintered at 1350$\sim$1450$^{\circ}C$ and mechanical characterization and microstructure analysis were conducted. Microhardness and fracture toughness were shown as 1357.4 Hv and 8.56 MPa $m^{1/2}$. respectively. Without alumina, they were 1311 Hv and 10.02 MPa $m^{1/2}$ respectively. By mixing two different oxides, it was possible to obtain high values of microhardness and fracture toughness. It was possible that was turned out nano-scale particle using the co-milling of high mechanical energy.

• Journal of the Korean Ceramic Society
• /
• v.28 no.1
• /
• pp.79-85
• /
• 1991

The effects of MnO2 on the microstructure and dielectric properties of Pb(Fe1/2Nb1/2)O3 ceramics prepared by KCl-NaCl molten salt synthesis(MSS) method have been investigated. As the amount of MnO2 increased up to 0.25wt%, the density increased and the grain size decreased, while above 0.25wt%, the density decreased with the grain growth. Dielectric constant increased with increasing the amount of MnO2, and dielectric loss decreased up to 0.25wt% and then increased. This is due to the compensation effect by the substitution of Mn4+ to Fe3+ and the appearance of the second phase.

• Journal of the Korean Ceramic Society
• /
• v.28 no.12
• /
• pp.943-952
• /
• 1991

Lead zirconate titanate(PZT) powders and thin films were prepared from an alkoxide-based solution by sol-gel method. Gelation of synthesized complex solutions, pyrolysis and crystallization behaviors of the dried powder were studied in accordance with a water content and a catalyst. PZT thin films were formed by spin-casting method on silicon and platinum substrates, and characterized. Ester produced from the reactions was completely removed when drying of the gel was finished. Pyrolysis property of the dried PZT gels were changed in order water content, class of catalyst, and quantity of catalyst. Crystalline Pb phase was transiently formed near 250$^{\circ}C$. Basic catalyst is good additive for a formation of perovskite phase in the films, and acidic catalyst for a densified film structure. By the analysis of RBS, Pb element in the PZT films were diffused into silicon substrate, and the pores, may be produced due to local densification around some grains in the films, make an origin of fault in microstructure when holding time goes to be longer at 700$^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.201-209
• /
• 1989

Fine Si-Al-OH coprecipitate powders were prepared from Si- and Al-alkoxides by the hydrolysis method. $\beta$-Sialon powder was obtained from prepared Si-Al-OH coprecipitate by the simultaneous reduction and nitridation method. The syntehsized Sialon powder was pressureless sintered at 175$0^{\circ}C$ for 90 min in N2 atmosphere. The characterization of the Sialon powder was performed with XRD, BET, SEM, TEM and particle size analysis. The sinterability and mechanical properties of sintered bodies were investigated in terms of relative density, M.O.R., fracture toughness, hardness and the morphology of microstructure. The highest values of their mechanical properties were obtained for the $\beta$-Sialon ceramics at Z=1 and those values are as follows : M.O.R., KIC and HV of $\beta$-Sialon ceramics(Z=1) are 499.1 MPa, 5.9MN/m3/2 and 18.7GPa, respectively.

• Journal of the Korean Ceramic Society
• /
• v.23 no.4
• /
• pp.78-84
• /
• 1986

Zirconium acetate solution which was obtained from $ZrOCl_2$.$8H_2O$ was condensed polymerized and drawn to fibers by pulling method. Drawn gel fibers fired at 130$0^{\circ}C$ were short porous and mechanically weak. But addition of CaO about 13m/o caused the fibers to have the cubic structure and relatively dense microstructure. In order to clarify the condition for the synthesis of zirconia fibers viscosity measurement DTA-TG analysis X-ray diffraction infrared spectroscopy, SEM and specific surface area were studied.

• Journal of the Korean Ceramic Society
• /
• v.25 no.6
• /
• pp.593-600
• /
• 1988

The properties of 10 kinds of MgO clinker were investigated to know the effect of MgO clinker's porperties on corrosion of MgO-C brick. For MgO clinker, chemical composition, porosity, density, periclase grain size, and microstructure were examined, while slag corrosion resistance was examined for MgO-C brick. In MgO clinker pore size and it's distribution, periclase grain size, impurities composition and the composition of grain boundaries are more important factors to determine corrosion degree of MgO-C brick than density, potosity and MgO purity.

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.228-234
• /
• 1989

Pressureless-sintering of SiC with additions of yttria and alumina was studied. SiC could be densified to about 97% of its theoretical density at 185$0^{\circ}C$ which is about 20$0^{\circ}C$ below the normal sintering temperature of SiC with boron and carbon. Yttria and alumina formed intergranular liquid phases at the sintering temperature and promoted densification by the liquid phase sintering mechanism. The microstructure of sintered specimens was equiaxed and the liquid phase appeared to wet and dissolve SiC grains. The fracture toughness was measured by indentation method and found to be 5.3MPa.m1/2. Processing flaws near the surface of specimens appeared to be the major fracture origin during 3-point bending tests.

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.267-275
• /
• 1989

YBa2Cu3O7-x oxide superconductors were fabricated by sintering and hotisostatic pressing (HIP), and their microstructures and properties were compared with each other. Thougha part of the second phase was observed along grain boundaries, their structures were consisted of single (123) phase and they had many porosities. But, porosities were remakably reduced by Hiping and the densification was brought about. The structure of (123) compound also showed a number of twins, which are typical of high Tc superconductors. The on-set temperature of YBa2Cu3O7-x compound sintered at 96$0^{\circ}C$ in oxygen and hipped at 88$0^{\circ}C$ was highest, but that shwoed 0 resistance at 87$^{\circ}$K, which is a little lower than the compound sintered at 96$0^{\circ}C$. HIP treatment also increased the critical current density of as-sintered compound. However, its value was low, which may be ascribed to the many pores of starting-sintered compact and partially to the second phase along grain boundaries.

• Journal of the Korean Ceramic Society
• /
• v.44 no.11
• /
• pp.650-654
• /
• 2007

[ $SnO_2$ ]-doped $TiO_2$ thin films were prepared from tin (IV) bis (acetylacetonate) dichloride and titanium diisopropoxide bis (acetylacetonate) with pluronic P123 or degussa P25 as a structural-directing agent. These hydrolyzed sol were spin coated onto Si(100) wafer substrate. The microstructure, morphology and bonding states of thin films were studied by field-emission scanning electron microscopy (FE-SEM), X-ray diffractometry (XRD), and X-ray photoelectron spectroscopy (XPS). The photocatalytic activity of these films was investigated by using indigo carmine solution.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.581-596
• /
• 2016

A comprehensive review on sliding and solid particle erosion wear characteristics of silicon carbide (SiC) ceramics and SiC composites is provided. Sliding or erosion wear behavior of ceramics is dependent on various material characteristics as well as test parameters. Effects of microstructural and mechanical properties of SiC ceramics are particularly focused to understand tribological performance of SiC ceramics. Results obtained between varieties of pairs of SiC ceramics indicate complexity in understanding dominant mechanisms of material removal. Wear mechanisms during sliding are mainly divided in two groups as mechanical and tribochemical. In solid particle erosion conditions, wear mechanisms of SiC ceramics are explained by elastic-plastic deformation controlled micro-fracture on the surface followed by radial-lateral crack propagation beneath the plastic zone.