• Journal of the Korean Ceramic Society
• /
• v.33 no.2
• /
• pp.135-142
• /
• 1996

Fly Ashes which are produced from coal-fired powder plants and classified as general waste can be used as raw materials for bricks and tiles because of their compositional similarity with clays. There was a limit of substituting fly ash for clay because plasticity decreased with increasing fly ash additions. Accordingly this study tried to suggest a feastibility of enhancing the substitution ratio by controlling the interfacial properties of fly ash. The slip with 1:1 volume ratio showed that best dispersive characteristics under the condition of pH 2 Filter pressed cakes made of pH 2 slips also showed better plastickity than those of untreated ones. of pH 2 Filter pressed cakes made of pH 2 also shwoed better plasticity than those of untreated ones.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.76-83
• /
• 2000

A 2-pole tunable bandpass filter was design and fabricated using ceramic coaxial resonators and varactor diodes for UHF band. By inspection of frequency characteristics of the T-and $\pi$-type inverter equivalent circuits, we can design a two-pole tunable BPF with only two varactors. The measured data of the filter show 800 MHz-900 MHz tunable center frequency range, 4.5 dB insertion loss, 0.5 dB passband ripple and at least 15 dB return loss, which agree well with the simulated results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.740-743
• /
• 2003

A multi-layer ceramic (MLC) chip type band-pass filter (BPF) is presented. The MLC chip BPF has the benefits of low cost and small size. The BPF consists of coulped stripline resonators and coupling capacitors. The BPF is designed to have an attenuation pole at below the passband for a receiver band of IMT-2000 handset. The computer-aided design technology is applied for analysis of the BPF frequency characteristics. The passband and attenuation pole depend on the coupling between resonators and coupling capacitance. The frequency characterics of the passband and attenuation pole are analyzed with the variation of the coupling between resonators and coupling capacitance. An equivanlent circuit and structure of MLC chip BPF are proposed. The frequency characteristics of the BPF is well acceptable for IMT-2000 application.

• Journal of the Korean Ceramic Society
• /
• v.50 no.4
• /
• pp.245-250
• /
• 2013

A hydroxyapatite air filter was made with hydroxyapatite powder, water and chitosan solution. The structures of the sintered HAp samples were determined by MP-XRD. Hydroxyapatite has antibacteria properties against Staphylococcus aureus, Klebsiella pneumoniae and Escherichia coli. The bacteria removal rate was 99.9%. In the case of Pseudomonas aeruginosa, Colon bacterium and Listeria monocytogenes, the hydroxyapatite air filters had a clear zone which confirmed antibacteria properties. Using the microscopy, we observed that the HAp powder absorbed E. coli bacteria.

• Journal of Korean Society for Atmospheric Environment
• /
• v.17 no.1
• /
• pp.75-84
• /
• 2001

Hot gas filtration method via using ceramic filters is an evolving technology applicable to numerous industrial and air pollution control processes. Alumino silicate, organic and inorganic binders were the major raw materials in manufacturing ceramic filters. In this work, disc type ceramic filters(50$\phi$$\times$10t) were manufactured by vacuum forming processes using ceramic raw materials. The porosity and bulk density of disc type ceramic filers ranged from 86 to 89% and from 0.27 to 0.36 g/㎤, respectively. In this work disc type ceramic medium were tested utilizing coupon experimental apparatus. Disc type filters showed high collection efficiencies over 99.96% with Darchs law coefficients of 4.1$\times$10(sup)10~9.63$\times$10(sup)10/$m^2$ depending on mean pore sizes. In addition, filtration and detachment of ceramic filters turned out to be performed effectively using 10 cm/sec face velocity, 5 minutes filtration cycle, 100msec pulse jet valve opening time and 3 bar pulsing pressure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.130-141
• /
• 1997

Work on the reduction of particulate matter(PM) from a diesel vehicl has led to a new trp system and a control method to control the combustion rate of the PM filtrated in the trap, which was named as 'Active Exhaust Feeding Regeneration(AEFR) System' by its operation mechanism. Ceramic cordierite filter is a major component of the trap and susceptible to thermal shock. Therefore the system should be designed to reduce the peak temperature and temperature gradients in the trap ; these have been considered to be the main factors causing thermal shock of the filter during the regeneration. It uses the engine's exhaust gas partially for the regeneration of the ceramic filter. It controlled bypass flow rate of the engine's exhaust gas precisely to control the temperature of the gas entrained into the filter. Gas temperatures were measured inside filter, and the oxygen concentration at the outlet of the filter was also monitored during the regeneration to analyze the combustion process of the PM. The temperature distributions and temperature gradients in the filter during the regeneration varied widely according to the regeneration control schemes. Finally, this system shows relatively low peak temperature and temperature gradients in the filter during its regeneration. It is considered that this system uses a mew method to control the combustion rate of the PM, which is different from the methods used in the previous studies.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.04a
• /
• pp.129.1-129
• /
• 2003

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.3
• /
• pp.361-369
• /
• 2004

A metal fiber bed has seldom been applied to the practical filtration process despite its excellent mechanical and chemical stability. The filter-bed used in this work was highly porous with open structure, of which apparent porosity was 80 ∼ 90%. Although pressure loss across the filter-bed was very low, separation efficiency was found to be quite high. This paper focuses on the basic filtration mechanisms of a metal filter-bed and a thin ceramic filter from fly ash for reference. The experimental parameters were face velocity, dust loading and porosity of filter-bed. Pressure drop increased with increasing face velocity and dust feeding load for both filters. It also showed that dust particles deposited in the deep flow path, finally resulting in clogging the pore channels. It thereby indicates that the dominating mechanism of the metal filter-bed would be depth filtration. Meanwhile, the thin fly ash composite filters trapped the aerated dust mainly on the surface of the filter medium, so that the instantaneously formed dust layer might cause a steep increase of pressure drop across the filtration system.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.3
• /
• pp.371-380
• /
• 2004

In the dust separation by using porous filter media, the structure of dust layer deposited on the filter surface of filter medium directly affects the effective filtration. The present study has investigated the specific resistance (K$_2$') of the dust layer and its porosity ($\varepsilon$$_{c}$) for three different filters; FA composite filter, metal fiber filter and stainless filter. The specific resistance (K$_2$') increased and at the same time the cake porosity ($\varepsilon$$_{c}$) decreased with the increase of filtration velocity, possibly due to the compressible effect of dust layer. However, under the low dust concentration, subsequent dust particles would block the open channels through the layer resulting in high specific resistance of the layer. The FA composite filter among three filters was shown to be the most effective filter for dust cake filtration at low filtration velocities less than 0.1 m/s for an approximate dust concentration of 5 g/㎥.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.214.1-214
• /
• 2003