• 한국정밀공학회지
• /
• 제21권6호
• /
• pp.131-138
• /
• 2004

The objective of this paper is to decide optimal location of a pin-hole to minimize stress concentration around the hole in a rotating disc. The focus of this investigation is to evaluate the effect of pin-hole on stress distribution around the hole using optimum design technique and finite element analysis. Design variables are the radial and the angular location of pin-hole from center of the hole and objective function is the maximum stress around hole in a rotating disc. Using first order method of optimization technique, we found that the maximum equivalent stress around the hole with optimized pin-hole could be reduced by 15.1% compared to that without pin-hole.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.184-187
• /
• 2005

The blade is an important part of rotating turbomachinery. The blade dynamic strength is of considerable importance as far as the reliability of operation and the life of the engine ate concerned. In this paper, blades are attached to a disk and coupled by means of damping wire. We assumes that the interfaces between the blade and disk dovetails are joined together, which means surface-to-surface contacts without friction. The damping wire is implemented using a beam element and temperature effect in the blade is neglected. Centrifugal forces ale applied by using an angular velocity to all elements in the system. The FEM results showed vibration characteristics in the blade disk system for the cases of a free-standing blade and blades with damping wire, respectively.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2003년도 춘계학술발표논문집
• /
• pp.256-259
• /
• 2003

Artificial heart is divided pulsation style and nonpulsation style greatly according to flowing of blood. nonpulsation pump is advantage of miniaturization avaliable because it is simple and non-volumic-pump than pulsation pump. Non pulsation pump is derided axial flow style and centrifugal style accordig to rotating style. An axial flow blood pump can be made smaller than a centrifugal blood pump because of its higher specific speed. A hemolysis is an important factor for the development of an axial flow blood pump. It is difficult to identify the areas where hemolysis nun. Evaluation of hemolysis both in in vitro and in vivo require a long time and are costly. Computational fluid dynamics(CFD) analysis enables the engineer to predict hemolysis on a computer. The aims of this study is Computational fluid dynamics in the whole axial flow pump and to verify the accuracy of prediction results of CFD analysis compare with in vitro experimental results.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(1)
• /
• pp.484-490
• /
• 1996

The Pressurizer Level Control System (PLCS) logic for YGN 5&6 was developed to incorporate the design changes on the Chemical and Volume Control System (CVCS). The YGN 5&6 CVCS uses the centrifugal charging pumps and letdown orifices replacing the positive displacement pumps and letdown control valves in the YGN 3&4 and UCN 3&4. The purpose of this study is to develop new PLCS as well as validate newly developed control logic and its implementation method in the simulation computer code. The analysis results show that the new PLCS has adequate ability to control the pressurizer level in response to the design bases events, and the simulation computer code is useful for YGN 5&6 NSSS design code.

• 자동차안전학회지
• /
• 제8권2호
• /
• pp.24-29
• /
• 2016

A small-sized turbocharger is generally used in downsizing engine for various vehicles. When a centrifugal compressor, which is one of the crucial units of the turbocharger, is downsized, the compressor has much more possibilities of being damaged because of its high rotating speed, causing insecure structural soundness. Thus, it is of essential to study on the improvement of the structural soundness of a small-sized turbocharger. In this study, numerical analysis on the various blade geometries and mass flow rate of the compressor was performed using the commercial software ANSYS CFX. In addition, the evaluation on the structural soundness of a compressor impeller for respective cases was conducted using ANSYS Mechanical. As a result, it was shown that the compressor had higher efficiency with increasingly secured structural soundness.

• 풍력에너지저널
• /
• 제5권1호
• /
• pp.50-55
• /
• 2014

Surface Permanent-Magnetic-Synchronous-Generator (SPMSG) discussed in the present study has operational characteristics such as high rotational speed over 1,000 rpm and centrifugal force of 12 kN·m for each magnet. Structure-development analysis for the minimization of rotor-core weights and the maximization of thermal emission is performed by applying the aluminum-laminated cap which combines the advantages of IPM and SPM in order to overcome the difficulty that attaching the magnet to rotor-core only with an adhesive. In this study, the simulations in terms of structure and electromagnetic were performed with the variable parameters such as shape and thickness of laminated-cap and division method of magnet. As a result, condition for minimized centrifugal force with minimum loss is derived.

• Current Optics and Photonics
• /
• 제8권2호
• /
• pp.170-182
• /
• 2024

The dimensional accuracy and consistency of a dual oil circuit centrifugal fuel nozzle are important for fuel distribution and combustion efficiency in an engine combustion chamber. A point cloud measurement method was proposed to solve the geometric accuracy detection problem for the fuel nozzle. An improved variance focus measure operator was used to extract the depth point cloud. Compared with other traditional sharpness evaluation functions, the improved operator can generate the best evaluation curve, and has the least noise and the shortest calculation time. The experimental results of point cloud slicing measurement show that the best window size is 24 × 24 pixels. In the height measurement experiment of the standard sample block, the relative error is 2.32%, and in the fuel nozzle cone angle measurement experiment, the relative error is 2.46%, which can meet the high precision requirements of a dual oil circuit centrifugal fuel nozzle.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1998년도 춘계학술대회 및 발표대회 강연 및 발표논문 초록집
• /
• pp.10-10
• /
• 1998

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2001년도 춘계학술강연 및 발표대회
• /
• pp.31-32
• /
• 2001

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2001년도 추계학술강연 및 발표대회
• /
• pp.49-50
• /
• 2001