• Journal of the Korean Geotechnical Society
• /
• v.20 no.6
• /
• pp.41-49
• /
• 2004

In general, open trenches or in-filled trenches have been used to isolate transmitting of vibration. Recently alternative methods, in which various materials are used for wall barriers have been proposed and performed in several sites. Although the effects of these methods are verified, resonable and qualitative evaluation methods have not yet been conducted. It may be because many factors, such as the characteristics of vibration sources, ground condition, and parameters of wall barrier are coupled complicatedly. In this study, a series of centrifugal modelings were conducted in order to examine the evaluation method of a vibration wall barrier when point load transmits to the surface. The experiments were performed with different stiffness of wall barriers and different depths of installations. Using the results obtained from tests, effects of those variables on the efficiency of vibration barrier were analyzed. Through this investigation we observed vibration transmission of under ground, and verified the applicability of ball dropping system which was developed in this study.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.8
• /
• pp.135-145
• /
• 2004

In this study, the behavior of unpropped diaphragm walls on decomposed granite soil was investigated through centrifugal and numerical modelling. Centrifuge model tests were performed by changing the interval distance of surcharge. Excavation was simulated during the centrifuge tests by operating a solenoid valve that allowed the zinc chloride solution to drain from the excavation. In these tests, ground deformation, wall displacement and bending moment induced by excavation were measured. FLAC program which can be able to apply far most geotechnical problems was used in the numerical analysis. In numerical simulation, Mohr-Coulomb model fur the ground model, an elastic model for diaphragm wall were used for two dimensional plane strain condition. From the results of model tests, failure surface was straight line type, the ground of retained side inside failure line had downward displacement to the direction of the wall, and finally the failure was made by the rotation of the wall. The angle of failure line was about 67 ∼ 74$^{\circ}$, greater than calculated value. The locations of the maximum ground settlement obtained from model tests and analysis results are in good agreements. The displacement of wall and the change of the embedment depth is likely to have linear relationship.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.15 no.3
• /
• pp.166-175
• /
• 2005

Health effects associated with metal working fluid (MWF) exposures include dermatitis, respiratory disease, hypersensitive pneumonitis, and asthma. Frequently, occupational exposures to MWFs are controlled by ventilating an enclosure with an air cleaning unit that includes a fan preceded by various kinds of filtration. There are several kinds of air cleaning units used in machining centers. But the associated troubles have hindered from efficiently using these devices. The main problem is the relatively short period of filter replacement. The reason is that the air cleaning units usually do not have the de-oiling systems, thus leading the earlier clogging of filters and reducing the flow rate of hood. Thus, the first stage of study was conducted to overcome this problem by developing the new oil mist collector equipped with the easy de-oiling system. The principle of de-oiling is that the centrifugal force generated by spinning the drum covered by filter fabric separates oils from the filter fabric. It would be very similar to the spin-dry laundry. By adopting this de-oiling technique, the problems associated with the conventional oil mist collectors could be solved. Several tests/analyses were performed to make the lab-scale oil mist collector. The collection efficiencies and the de-oiling efficiencies of commercially available filter fabrics were tested. Subsequently, the endurance test were conducted by observing SEM photos of filter fabrics and measuring tensile strength/expansion coefficient after spinning the filter drum for 20 minutes at the different rotation speeds. By doing these experiments, the most appropriate filter fabric and rotation speed/duration were selected. Finally, the new oil mist collector was designed. In the near future, this device must be tested in the real machining center.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.6
• /
• pp.599-605
• /
• 2013

The characteristics of centrifugal pump performance according to fluid viscosity change were studied experimentally. A small volute pump with low specific speed was tested by changing the viscosity of an aqueous solution of sugar and glycerin, which is considered a Newtonian fluid. After finishing the test, the total head, shaft horsepower, and pump efficiency were compared with those of a water pump. The results are summarized as follows: (1) when the fluid viscosity is increased, the shut-off head shows very little change but the total head decreases gradually as the flow increases, and this makes the H-Q curve leaning rapidly, and (2) when the fluid viscosity is increased, the shaft horsepower shows very little change at the shutoff condition; however, the shaft horsepower increases more rapidly with an increase in the flow and viscosity.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.3
• /
• pp.165-172
• /
• 2017

In this study, centrifugal fan blades used to circulate cold air inside a household refrigerator were optimized to achieve high performance and low noise by using the response surface method, which is frequently employed as an optimization algorithm when multiple independent variables affect one dependent variable. The inlet and outlet blade angles, and the inner radius, were selected as the independent variables. First, the fan blades were optimized to achieve the maximum volume flow rate. Based on this result, a prototype fan blade was manufactured using a 3-D printer. The measured P-Q curves confirmed the increased volume flow rate of the proposed fan. Then, the rotation speed of the new fan was decreased to match the P-Q curve of the existing fan. It was found that a noise reduction of 1.7 dBA could be achieved using the new fan at the same volume flow rate.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.5
• /
• pp.433-441
• /
• 2011

The optimization of a centrifugal compressor was conducted. The ANN (Artificial Neural Network) was adopted as an optimization algorithm, and it was learned and trained with the DOE (Design of Experiment). In the DOE, it was predicted the main effect and the interaction effect of design variables to the objective function. The ANN was improved in the optimization process using the GA (Genetic Algorithm). When any output at each generation was reached a standard level, it was re-calculated by the CFD (Computational Fluid Dynamics) and it was applied to develop a new ANN. After 6th generation, the prediction difference between ANN and CFD was less than 1%. A pareto of the efficiency versus the pressure ratio was obtained through the 21th generation. Using this method, the computational time for the optimization was equivalent to the time consumed by the gradient method, and the optimized results of multi-objective function were obtained.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2364-2369
• /
• 2015

In this paper, the optimum RPM was suggested comparing rotor filling rate of RPM through the analysis of rotor's filling rate as studying and developing centrifugal-casting machine's method for high precision rotor in order to increase the related types of business's productivity. The result was similar to other result in industrial site, showing 99.47% of filling rate when rotational speeds are 600 rpm, so it is considered that if this result is conducted with additional research, it will be possible to plan a better process design. Besides, the optimum temperature of compact ladle was examined to produce high quality casting product through the analysis of compact ladle's conductivity. In the case of the heating device's absence using nicrome wire, Al solution solidifies falling drastically into $427^{\circ}C$. However, it is feasible to work over $427^{\circ}C$ which is the melting temperature of aluminium solution when the heating device of nicrome wire is included. It reveals that there is little temperature change.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.48 no.3
• /
• pp.301-307
• /
• 2015

Phlorotannins and marine algal polyphenols, including dieckol, 6,6-bieckol, phloroglucinol, phlorofucofuroeckol-A, and eckol, were isolated from brown seaweeds. These compounds have beneficial bioactivities, and Ecklonia cava has become widely used for the extraction and isolation of phlorotannins. Eckol, in particular, has been to shown to have antioxidant, anti-inflammatory, anticoagulatory, and photoprotective properties. However, due to its low abundance in weaweed, the isolation and purification of eckol are difficult. Its limited availability renders the isolation and purification of eckol labor-intensive processes. Centrifugal partition chromatography (CPC) is an efficient technique for the isolation and purification of eckol. In this study, eckol was isolated from the ethyl acetate fraction of the 70% ethanol extract of E. cava using CPC with a two-phase solvent system of a n-hexane:EtOAc:methanol:water (2:8:3:7, v/v) solution. The purity and anti-inflammatory activity of the isolated eckol were verified by high-performance liquid chromatography and by assaying lipopolysaccharide-induced inflammatory responses in an immortalized murine BV2 microglial cell line, respectively. In conclusion, CPC is a useful technique for simple and efficient isolation of eckol from E. cava.

• Journal of the Korean Magnetics Society
• /
• v.6 no.6
• /
• pp.388-396
• /
• 1996

Magnetic properties of sintered Fe-79Ni-4Mo cores made of centrifugal atomized powders were investigated. $H_{c}$ and $\mu_{a}$ of the cores sintered at $1350^{\circ}C$ for 2 hours measured at 60 Hz at a magnetic field of 10 Oe showed the best properties. Particularly the properties of $H_{c}$ and $\mu_{a}$ measured at low field (< 0.2 Oe) were found to increase with increasing the particle size of the core samples. It resulted from the domain wall motion depending on the grain size of sintered bodies. The best D, C magnetic properties of $H_{c}$ and $\mu_{max}$ were 0.085 Oe and 40000, respectively. A, C properties of the same cores showed the $\mu_{a}$ of 11000. The magnetic properties of sintered cores always exhibited an enhanced AC/DC performance by using the powders mixed with two different particle sizes. Those properties of cores are expected to apply for current transformer.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.1
• /
• pp.1-8
• /
• 2016

In this paper, we perform structural analysis for a base frame which is used to support a motor for large centrifugal compressor drives and a safety assessment according to the concrete placement. First, the structural analysis about four loading conditions for the motor base frame was conducted and the structural safety was evaluated through both the maximum distortion energy theory and Mohr-Coulomb theory. It was possible to perform a more reasonable safety evaluation against local stresses occurring at the discontinuous portion of the fragile structural members by applying the safety assessment through ASME VIII Div. 2. In addition, the motor base frames with and without the internal concrete placement were quantitatively compared by the structural analysis and safety evaluation using ASME code and it was found to improve the structural integrity due to the concrete placement.