• Journal of Biosystems Engineering
• /
• 제4권1호
• /
• pp.1-23
• /
• 1979

The use of barley seeder attached to rotary tiller in the rural area has a significant meaning not only for the solution of labor peak season, but also for the increase of land utilization efficiency. The facts that presently being used barley seeders are all based on the mechanical principles of the reverse rotation, center drive and are all using forward rotating tine, which is used to be easily and heavily worn out when it rotates reversely, raise problem of recommending them to rural area in Korea. Therefore, the main objective of the study was to develop new type of rotary tine attachable to barley seeders. To attain the objective the following approaches were applied. (1) The kinematic analysis of reverse rotating barley seeders. (2) The studies on the soil bin and artificial soil. (3) The comparative experiment on the power requirement of prototype tine. The results obtained from the studies are summarized as follow: 1. The kinematic analysis of barley seeder attached to rotary tiller: The following results were obtained from the kinematic analysis for deriving general formulae of the motion and velocity characterizing the rotary tine of barley seeders presently being used by farmers. a) The position vector (P) of edge point (P) in the rotary tine of reverse rotating, center drive was obtained by the following formula. $$P=(vt+Rcos wt)i+Rsin wt j+ \{ Rcos \theta r sin \alpha cos (wt- \beta +\theta r) +Rsin \theta r sin \alpha sin (wt-\beta + \theta r) \} lk $$ b) The velocity of edge point $(P^')$ of reverse rotating, center drive rotary tine was obtained by the following formula. $$(P^')=(V-wR sin wt)i+(w\cdot Rcoswt)j + \{ -w\cdot Rcos \theta r\cdot sin \alpha \cdot sin (wt-\beta +\theta r) + w\cdot Rsin \theta r\cdot sin \alpha \cdot cos (wt- \beta + \theta r \} k $$ c) In order to reduce the power requirement of rotary tine, the angle between holder and edge point was desired to be reduced. d) In order to reduce the power requirement, the edge point of rotary tine should be moved from the angle at the begining of cutting to center line of machine, and the additional cutting width should be also reduced. 2. The studies on the soil bin and artificial soil: In order to measure the power requirement of various cutting tines under the same physical condition of soil, the indoor experiments Viere conducted by filling soil bin with artificially made soil similar to the common paddy soil and the results were as follows: a) When the rolling frequencies$(x)$ of the artificial soil were increased, the densIty$(Y)$ was also increased as follows: $$y=1.073200 +0.070780x - 0.002263x^2 (g/cm^3)$$ b) The absolute hardness $(Y)$ of soil had following relationship with the rolling frequencies$(x)$ and were increased as the rolling frequencies were increased. $$Y=37.74 - \frac {0.64 + 0.17x-0. 0054x^2} {(3.36-0.17x + 0.0054x^2)^3} (kg/cm^3)$$ c) The density of soil had significant effect on the cohesion and angle of internal friction of soil. For instance, the soil with density of 1.6 to 1.75 had equivalent density of sandy loam soil with 29.5% of natural soil moisture content. d) The coefficient of kinetiic friction of iron plate on artificial soil was 0.31 to 0.41 and was comparable with that of the natural soil. e) When the pulling speed of soil bin was the 2nd forward speed of power tiller, the rpm of driving shaft of rotary was similar to that of power tiller, soil bin apparatus is indicating the good indoor tester. 3. The comparative experiment on the power requirement of prototype tine of reverse rotating rotary: According to the preliminary test of rotary tine developed with various degrees of angle between holder and edge pcint due to the kinematic analysis, comparative test between prototype rotary tine with $30 ^\circ $ and $10 ^\circ$ of it and presently being used rotary tine was carried out 2nd the results were as follows: a) The total cutting torque was low when the angle between holder and edge point was reduced. b) $\theta r$ (angle between holder and edge point) of rotary tine seemed to be one: of the factors maximizing the increase of torque. c) As the angle between holder and edge point ($\theta r$) of rotary tine was $30 ^\circ $ rather than $45 ^\circ $, the angle of rotation during cutting soil was reduced and the total cutting torque was accordingly reduced about 10%, and the reduction efficiency of total cutting torque was low when the angle between holder and edge point ($\theta r$) of rotary tine was $10 ^\circ $, which indicates that the proper angle between holder and edge point of rotary tine should be larger than $10 ^\circ $ and smaller than $30 ^\circ $ . From above results, it could be concluded that the use of the prototype rotary tine which reduced the angle between holder and edge point to $30 ^\circ $, insted of $45 ^\circ $, is disirable not only decreasing the power requirements, but also increasing the durabie hour of it. Also forward researches are needed, WIlich determine the optimum tilted angle of rotary brocket, and rearrangement of the rotary tine on the rotary boss.

• Radiation Oncology Journal
• /
• 제21권2호
• /
• pp.174-181
• /
• 2003

목적: 유방암 환자를 삼문으로 방사선치료할 경우 유방의 접면 영역과 쇄골상 영역의 기하학적 일치를 이루기 위해 갠트리를 회전한 상태에서 테이블을 회전하는 방법이 사용되며, 이때 접면 조사의 posterior edge에 발생할 수 있는 어긋남을 필름선량측정법과 삼차원입체조영치료계획을 통하여 확인하고, 그 어긋남의 해결방법으로 콜리메이터의 각도를 보정해주는 방법들을 연구하였다. 대상 및 방법: 어긋남의 보정을 위해 쇄골상 영역과 유방의 접면 영역을 반쪽 빔 블록과 tangential field block을 사용하여 모의치료한 후 테이블 회전을 하지 않은 상태에서 환자의 몸에 접면 빔의 posterior edge에 선을 긋고, 테이블을 회전시킨 상태에서의 광조사야의 posterior edge와 테이블 회전 이전에 환자의 몸에 그어 놓은 선과 일치되도록 콜리메이터를 회전시키는 방법과, 본 연구에서 고안한 방법인 삼각함수로부터 유도시킨 다음과 같은 공식에 따라 콜리메이터를 회전하여 posterior edge의 어긋남을 보정하고 두 방법을 비교하였다. Co=$2sin^{-1}${$sin\{theta}\{cdot}sin(C/2)$} (Co: collimator angle, $\theta$: angle between tangential beam and table, C: couch angle) 결과: 필름선량측정법을 이용하여 콜리메이터를 보정하지 않은 경우 내외측의 접면 빔의 posterior edge가 어긋남을 확인할 수 있었으며, 콜리메이터를 보정함으로써 posterior edge의 일치함을 확인할 수 있었다. 위 두 방법에서 콜리메이터의 회전 각도는 동일하였다. 또한 전산화된 삼차원입체조영치료계획을 통하여, 접면 빔의 posterior edge의 어긋남을 확인할 수 있었으며, 콜리메이터를 회전하여 보정 함으로써 posterior edge의 일치를 확인할 수 있었다. 각각의 선량체적표를 비교할 경우, 콜리메이터를 보정하여 posterior edge의 일치를 이룬 경우가 더 적은 용적의 폐가 조사되는 것을 확인할 수 있었다. 결론: 유방암 환자의 방사선 치료에서 삼문으로 치료할 경우에 갠트리와 테이블을 동시에 회전하여 쇄골위 영역의 아래 면과 접면 빔의 윗면을 일치시킬 때 각각의 접면 빔의 posterior edge가 어긋남을 인지해야 하며, 약간의 콜리메이터를 회전시킴으로써 이 어긋남은 보정가능하고, 폐에 조사되는 방사선 양도 줄일 수 있었다.

• 대한임상전기생리학회지
• /
• 제2권1호
• /
• pp.9-17
• /
• 2004

The purpose of this study are to determine the proper radiographic measurements for hip deformity in spastic cerebral palsy patients, and the correlation of hip deformity with neurological involvement, ability of ambulation. Thirty children with cerebral palsy(22 males, 8 females) were evaluated by measurement of the migration index, acetabular index, center edge angle from bilateral hip APs(anterior posterior view). The result are as follows; 1. The incidence of hip dislocation, among the thirty children fifteen children were found to be dislocated, and more significantly high in non-walking group than in walking group(p<0.05) and in quadriplegia than in diplegia(p<0.05). 2. When compared to normal hip and dislocation hip, the migration index was significantly higher(p<0.01) and the center edge angle was lower in the dislocation hip than in the normal hip. 3. Correlation of radiological findings in right and left hip, the migration index and the center edge angle were highly correlated(p<0.01). We recommand regular intervals X-ray study for early diagnosis and management of hip dislocation in spastic cerebral palsy.

• 제어로봇시스템학회논문지
• /
• 제8권9호
• /
• pp.812-817
• /
• 2002

This paper presents a development of high accuracy aligner and describes a method to find the orientation of a substantially circular disk shaped wafer with at least one flat region on an edge thereof. In the developed system, the wafer is spun one 360 degree turn on a chuck and the edge position is measured by a linear array to obtain a set of data points at various wafer orientation. The rotation axis may differ from wafer center by an unknown eccentricity. The flat angle is found by fitting a cosine curve to the actual data to obtain a deviation. The maximum deviation is then corrected for errors due to a finite number of data points and wafer eccentricity by calculating an adjustment angle from data points on the wafer fiat. After determining the flat angle the wafer is spun to the desired orientation. The wafer eccentricity can be calculated from four of the data points located away from the flat edge region. and the wafer is then centered.

• Applied Microscopy
• /
• 제24권3호
• /
• pp.78-86
• /
• 1994

A TEM study on proeutectoid ${\alpha}$ reaction at sub-eutectoid temperatures has been made in hypoeutectoid Ti-3.gw/o Co and Ti-5.2w/o Fe alloys. Widmanstatten ${\alpha}$ plates were formed in both alloys within the ${\beta}$ matrix with some modification of degenerate forms. These degenerate plates were formed by the sympathetic nucleation of ${\alpha}$ plates at ${\alpha}:{\beta}$ interphase boundaries. Three types of sympathetic nucleation, i.e., edge-to-edge, face-to-edge, face-to-face, were found in both alloys. The edge-to-edge sympathetically nucleated crystals formed a low-angle boundary between two crystals. The ${\alpha}:{\beta}$ interphase boundaries were found to be partially coherent interfaces which consist of regularly spaced misfit dislocations. The growth of these interphase boundaries were accomplished by the lateral movement of growth ledges. The intersection points of two ${\alpha}$ plates or the low angle boundaries which had formed by edge-to-edge sympathetic nucleation played a role as the potential sources of growth ledges during the growth of plate. The interfacial structures and the spatial morphologies of the degenerate proeutectoid ${\alpha}$ plates would be expected to influence the nucleation and growth of the succeeding eutectoid decomposition process.

• Tribology and Lubricants
• /
• 제34권1호
• /
• pp.16-22
• /
• 2018

Cylindrical turbine guide bearings (TGBs) with simple plain pads have conventionally been used in vertical hydro-power turbine-generator applications in order to provide turbine runner shafts with smooth rotation guides and supports. To overcome low-load/low-eccentricity performance drawbacks, such as very low film stiffness and lack of design credibility in the stiffness values themselves, of conventional cylindrical TGBs, the introduction of a rotational-directional leading-edge taper to each partitioned pad, simply pad leading-edge taper, has been found to be very effective in enhancing their design-application availability and usefulness. In this study, we investigate the effects of taper angle and length for given taper heights in detail in order to systematically establish the effectiveness of design on the performance improvement of vertical hydro-power application cylindrical TGBs with pad leading-edge tapers. The analysis results with $4-Pad{\times}1-Row$ cylindrical TGBs show that the lubrication performance of the cylindrical TGBs is optimized with an approximate taper angle ratio of 0.8 and taper length ratio of 0.9. We conclude that the introduction of pad leading-edge tapers along with the optimization of taper designs can be very effective in improving the overall operation reliability of cylindrical TGBs and the rotordynamic characteristics of vertical hydro-power turbine-generator rotor-bearing systems as well, to which the TGBs are applied.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.943-946
• /
• 1998

In this paper, we applied FFT to PCB Images, cutting unnecessary singals and noise, moving the starting point to center of image and used rotaion transform. from the detected edge Hough Transform identify the length, but not the angle, so we matched PCB images with using rotation transform to identify length and angle. After rotation transform we employ Least Squared Method to exact stereo matching.

• 제어로봇시스템학회논문지
• /
• 제14권1호
• /
• pp.54-61
• /
• 2008

This paper proposes a new algorithm for detecting and recognizing overlapped objects among a stack of arbitrarily located objects using a signature representation scheme. The proposed algorithm consists of two processes of detecting overlap of objects and of determining the boundary between overlapping objects. To determine overlap of objects, in the first step, the edge image of object region is extracted and those areas in the object region are considered as the object areas if an area is surrounded by a closed edge. For each object, its signature image is constructed by measuring the distances of those edge points from the center of the object, along the angle axis, which are located at every angle with reference to the center of the object. When an object is not overlapped, its features which consist of the positions and angles of outstanding points in the signature are searched in the database to find its corresponding model. When an object is overlapped, its features are partially matched with those object models among which the best matching model is selected as the corresponding model. The boundary among the overlapping objects is determined by projecting the signature to the original image. The performance of the proposed algorithm has been tested with the task of picking the top or non-overlapped object from a stack of arbitrarily located objects. In the experiment, a recognition rate of 98% has been achieved.

• 반도체디스플레이기술학회지
• /
• 제11권2호
• /
• pp.1-6
• /
• 2012

In this study, a high performance rotary magnet type magnetron source for roll-to-roll sputter system has been developed. We analyzed the density of magnetic field as a function of size variation of the magnet which are in the center and edge of the target. The target efficiency showed the best result when the width of center magnet, the width of edge magnet, the angle of edge magnet, and the rotation angle of Yoke are 20mm, 10mm, $56^{\circ}$, and $16^{\circ}$, respectively. On the basis of the results of magnet array, Roll-to Roll magnetron source was fabricated and tested. The uniformity of the film thickness and that of the sheet resistance was ${\pm}1.62%$ and ${\pm}4.13%$, and the resistivity was $2.79{\times}10^{-3}W{\cdot}cm$.

• 융합보안논문지
• /
• 제8권4호
• /
• pp.127-134
• /
• 2008

본 연구는 투명 성질을 가진 물방울의 윤곽선에 대한 효율적인 검출을 통해 분석 장비의 자동 측정에 대한 정확성을 향상시키는 것을 목적으로 한다. 투명성질을 가지는 원의 윤곽선 검출을 위해 밝기 분포에 대한 국소적 미분 대신에 적응성 방향 미분(Adaptive Directional Derivative；ADD)이라는 비국소적 연산자를 도입함으로써 에지의 램프 폭의 변화에 무관하게 에지 검출에 적용할 수 있는 MADD(Modified Adaptive Directional Derivative) 알고리즘을 사용한다. 이 방법은 램프 구간 내에서 방향 미분 값을 가중치로 사용하여 픽셀들의 위치를 평균한 방향 미분의 국소 중심(Local Center of Directional Derivative；LCDD)등의 위치를 찾는 추가적인 과정없이, 정확한 에지 픽셀의 위치가 완전 선명화 사상에 의한 단순 계단 함수의 위치로 자연스럽게 결정될 수 있다. 제시된 에지 검출 방법을 표면분석 기술인 접촉각 연산에 적용하여 실험 및 결과 분석을 통해 제안 기법의 타당성 및 효율성을 검증한다.