• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 추계학술발표대회 논문집
• /
• pp.246-250
• /
• 2009

String & tabbing step in the crystalline PV module manufacturing process for the temperature directly affects solar cells. In fact, in the manufacture of PV modules tend to be temperature factor and the corresponding changes n the output shows the same characteristics. In this journal, it will be considered about thermal characteristics, especially changes of characteristic in high temperature of the solar cell through experiment that we measure electric output characteristics of solar cells after those are applied with high temperature changes for two seconds. And we can think about the possibility of efficiency improvements over looks in PV module manufacturing processes.

• 한국전기전자재료학회논문지
• /
• 제36권1호
• /
• pp.42-48
• /
• 2023

Abstract: In this study, an induction heating system using resonance is developed to remove remaining moisture and contaminations which could be generated during fabricating secondary batteries. This system is composed of power supply and induction coil. Power supply needs an oscillator, zero crossing detection, frequency tracking function, and induction coil needs a dummy coil to obtain a uniform temperature distribution. It is very important to obtain a uniform heating temperature distribution of battery cell case in the induction heating system before pouring electrolyte into battery cell. Experimental results show a temperature distribution deviation of below 1℃ in the external position of battery cell cases. As well, the temperature of battery cell itself shows distribution of 40℃±3℃.

• 한국지열·수열에너지학회논문집
• /
• 제14권3호
• /
• pp.8-14
• /
• 2018

PV module power is calculated on PV module surface temperature adjustment by irradiation on the summer and autumn in NOCT(Nominal Operating Cell Temperature) conditions. The summer and autumn periods were selected because of large variation in outdoor air temperature and irradiation. This study was performed to understand relationship between PV module surface temperature and photovoltaic power using field measurement. As a results, it was determined that the amount of irradiation was proportional to the amount of photovoltaic power in the field measurement. However, it was also identified that the PV power generation decreased by increased PV module surface temperatures due to irradiation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 춘계학술대회 논문집 전기설비전문위원
• /
• pp.186-188
• /
• 2009

In this thesis, output voltage, current and power of solar module were classified by irradiation and module temperature from data of overall operating characteristics collected for one year in order to manage efficient photovoltaic generation system and deliver maximum power. In addition, from these data, correlations between irradiation, module temperature of photovoltaic cell and amount of power given by photovoltaic cell was quantitatively examined to deduce optimization of the design and construction of photovoltaic generation system. The results of this thesis can be summarized as follows. As output power characteristics according to a temperature range of 10$\sim$50[], output power was increased with an increase in temperature. Since output power increases with temperature increase, the result corresponds well to the related equation on temperature and output power.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.1-6
• /
• 2012

This paper addresses the issue of Renewable Energy for Electricity Storage device is one of the NAS (Sodium-Sulfur) battery will be about the module. For safety reasons, not the actual battery cells using a dummy cell in the module's operating temperature setting to examine the characteristics of the insulation vacuum of the wall temperature and external temperature changes measured over time. Upper and lower boundaries of the wall vacuum insulation characteristics cotton C intervals over time, average $5^{\circ}C$, but the temperature is rising, 4C section with little temperature change did not occur. On the other hand, about $3^{\circ}C$ in section 4D, and it was confirmed that the temperature rises. Wall vacuum insulation characteristics over time to look at the experiments and measurements are described.

• 한국수소및신에너지학회논문집
• /
• 제29권1호
• /
• pp.56-63
• /
• 2018

In this study, a $100cm^2$ cell frame for a molten carbonate fuel cell was designed using CFD analysis. Electrochemical reactions, gas flow, and the heat transfer in $100cm^2$ cell frame were modeled using COMSOL Multiphysics. Two design variables such as the height of the cell frame and the length of the gas input area were determined to obtain minimized temperature distribution and uniform gas distribution. With two design parameter such as height of the cell frame and the length of the gas flow channel, the temperature difference in the cell fame was decreased to $5^{\circ}C$ and the gas uniformity in the flow channel were achieved.

• 한국산학기술학회논문지
• /
• 제15권7호
• /
• pp.4065-4071
• /
• 2014

PV셀과 리본의 솔더링 공정에서 열풍온도에 따른 $200{\mu}m$ 두께의 PV셀의 온도분포와 변형량의 해석 결과는 실험 측정치와 거의 일치함을 알 수 있었다. 또한 전기효율은 설정온도 $390^{\circ}C$로 PV셀을 솔더링한 모듈에서 가장 좋은 결과가 나타났다. 열풍온도를 $350^{\circ}C$로 설정하고 $150{\mu}m$ 두께의 PV셀을 솔더링 해석한 결과, 최대 변형량이 약 5.9mm로서 상당히 큰 값임을 확인할 수 있었으며, 열풍온도를 보다 낮은 온도로 설정해야 변형량이 감소하고 전기효율이 향상될 것을 예측하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제12권4호
• /
• pp.449-457
• /
• 2012

The program/erase (P/E) cyclic endurances including bias temperature instability (BTI) behaviors of Metal-$Al_2O_3$-Nitride-Oxide-Semiconductor (MANOS) memories are investigated in comparison with those of Semiconductor-Oxide-Nitride-Oxide-Semiconductor (SONOS) memories. In terms of BTI behaviors, the SONOS power-law exponent n is ~0.3 independent of the P/E cycle and the temperature in the case of programmed cell, and 0.36~0.66 sensitive to the temperature in case of erased cell. Physical mechanisms are observed with thermally activated $h^*$ diffusion-induced Si/$SiO_2$ interface trap ($N_{IT}$) curing and Poole-Frenkel emission of holes trapped in border trap in the bottom oxide ($N_{OT}$). In terms of the BTI behavior in MANOS memory cells, the power-law exponent is n=0.4~0.9 in the programmed cell and n=0.65~1.2 in the erased cell, which means that the power law is strong function of the number of P/E cycles, not of the temperature. Related mechanism is can be explained by the competition between the cycle-induced degradation of P/E efficiency and the temperature-controlled $h^*$ diffusion followed by $N_{IT}$ passivation.

• 환경생물
• /
• 제35권2호
• /
• pp.152-159
• /
• 2017

For the effective seedling production of the hard shelled mussel, Mytilus coruscus, this study assessed the effects of the dietary value of live food, density, water temperature and salinity on growth and survival rate of the larvae. The optimal survival rate and growth rate were examined under differing conditions of water temperature, salinity, and rearing density for 30 days. The three groups were provided different feeding organisms, such as Isochrysis galbana and Teleaulax suecica. The mixtures were provided at a rate of $5{\times}10^4cell\;mL^{-1}$. The best growth was observed in the group with conditions $21^{\circ}C$ water temperature ($16.2{\pm}9.1{\mu}m$), 33 psu of salinity ($16.82{\pm}3.9{\mu}m$), $2500individual\;m^{-2}$ ($17.2{\pm}5.9{\mu}m$), and fed with $5{\times}10^4cell\;mL^{-1}$ of I. galbana and T. suecica mixture ($16.0{\pm}7.3{\mu}m$). The highest survival rate was found in the group at conditions $18^{\circ}C$ water temperature (66.4%), 33 psu of salinity (24.4%), $2500individual\;m^{-2}$ (65.8%), and fed with $5{\times}10^4cell\;mL^{-1}$ of I. galbana and T. suecica mixture (58.8%). We therefore conclude that the suitable culture conditions for the stable production of hard shelled mussel artificial seedlings was at 18 to $21^{\circ}C$ of temperature, 30 to 33 psu of salinity, 2500 to $5000individual\;m^{-2}$ of rearing density, and feeding supplement of $5{\times}10^4cell\;mL^{-1}$ of I. galbana and T. suecica mixture under semi running water system.

• 대한임상검사과학회지
• /
• 제38권3호
• /
• pp.147-151
• /
• 2006

Although various automated CBC analyzers with different WBC analytical principles were consequently introduced to clinical laboratory, the specific information concerning the suitability or unsuitability of aging samples is scarce. For this reason, we studied the effect of storage duration and temperature on CBC parameter in SE-9000 (SYSMEX Medical Electronics Co., Ltd., Kobe, Japan), automated CBC analyzer. We tested 32 K3-EDTA specimens with SE-9000 during 72 hours. Specimens were kept at room temperature (RT) and refrigerated and were analyzed at 0 hr, 4 hr, 8 hr, 24 hr, 48 hr and 72 hr after the collection of the specimens. The percentage changes from initial value for each parameters were calculated. Among the CBC parameters, hemoglobin, red blood cell count, mean corpuscular hemoglobin and platelets were stable for the study period at both temperatures. The mean corpuscular volume (MCV), hematocrit (Hct) and red cell distribution (RDW) increased and the mean corpuscular hemoglobin concentration (MCHC) decreased over time at room temperature. These parameters were stable when refrigerated. The leukocyte count was stable during 72hr at RT and when refrigerated. At room temperature, the relative percentages of neutrophils tend to increase, whereas those of lymphocyte and monocytes tend to decrease after 48 hours. When refrigerated, those of neutrophils and monocytes tend to increase, whereas those of lymphocytes tend to decreased over time. CBC parameters of refrigerated specimen were reliable for 72 hr for the exception of differential count from 24 hr but many CBC parameters, such as MCV, Hct, MCHC, RDW and differential count of leukocyte of blood stored at room temperature for 24 hr were unreliable.