• Microbiology and Biotechnology Letters
• /
• v.40 no.4
• /
• pp.414-418
• /
• 2012

The quantity of research on microbial fuel cells has been rapidly increasing. Microbial fuel cells are unique in their ability to utilize microorganisms and to generate electricity from sewage, pig excrement, and other wastewaters which include organic matter. This system can directly produce electrical energy without an inefficient energy conversion step. However, with MFCs maximum power production is limited by several factors such as activation losses, ohmic losses, and mass transfer losses in cathodes. Therefore, electron acceptors such as nitrate and ferric ion in the cathodes were utilized to improve the cathode reaction rate because the cathode reaction is very important for electricity production. When 100 mM nitrate as an electron acceptor was fed into cathodes, the current in single-cathode and dual-cathode MFCs was noted as $3.24{\pm}0.06$ mA and $4.41{\pm}0.08$ mA, respectively. These values were similar to when air-saturated water was fed into the cathodes. One hundred mM nitrate as an electron acceptor in the cathode compartments did not affect an increase in current generation. However, when ferric ion was used as an electron acceptor the current increased by $6.90{\pm}0.36$ mA and $6.67{\pm}0.33$ mA, in the single-cathode and dual-cathode microbial fuel cells, respectively. These values, in single-cathode and dual-cathode microbial fuel cells, represent an increase of 67.1% and 17.6%, respectively. Furthermore, when supplied with ferric ion without air, the current was higher than that of only air-saturated water. In this study, we attempted to reveal an inexpensive and readily available electron acceptor which can replace platinum in cathodes to improve current generation by increasing the cathode reaction rate.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.31 no.2
• /
• pp.259-266
• /
• 1998

A study on the biological and chemical characteristics in the middle last Sea of Korea was carried out at 31 stations in October $11\~18$, 1995 on board the R/V Tam-Yang. The chlorophyll a concentration, new and regenerated production, and the vertical diffusion of nitrate from the thermocline structure were investigated. From the vertical distribution of chlorophyll a, subsurface maxima were observed near the thermorline at most stations including the frontal zone, except at the southern stations where the maximum chloropyll a concentration occurred at the surface, The nanophytoplankton was the most dominant fraction comprising $83.5\%$ of total phytoplankton cell numbers, but netphytoplankton were common at the southern stations where the dominant species were Rhizosolenia sp. Nitrogenous new production and regenerated productions were measured using the stable isotope $^{15}N$ nitrate and ammonia uptake method. The vertically integrated nitrogen production varied between 8.470 and $72.945\;mg\;N\;m^{-2}\;d^{-1}$. The f-ratio, which is the traction of new production from primary production, waried between 0.03 and 0.72, indicating that $3\%$ to $72\%$ of primary production was supported by the input of nutrients from below the euphotic zone and the rest are supported by ammonia recycled within the euphotic layer. This range of f-ratio encompasses from extremely oligotrophic to eutrophic area characteristics. The differences in productivity and f-ratio among stations were related to frontal structure and the bottom topography. The values were high near the frontal zone and low outside of it, and the station near Ulleng Island showed the highest f-ratio. Vertical diffusion coefficients were calculated from both the water column stability (Kz-1) of King and Devol's equation (1979) and new nitrogen requirement (Kz-2). The values of Kz-2 ($0.11\~0.55\;cm^2/s$) were relatively low compared to the values reported previously.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.6
• /
• pp.590-598
• /
• 2005

An adequate method to identify chromium separation, Cr(III) and Cr(VI), in water samples were studied by using High Performance Liquid Chromatography(HPLC) coupled with Inductively Coupled Plasma Mass Spectometer(ICP-MS) equipped with Dynamic Reaction Cell(DRC). The characteristic distribution of Cr(III) and Cr(VI) in the raw water taken at the six water intake stations in Seoul, was analyzed by the method developed by the authors. The chromium species separated by HPLC was isocratically conducted by using tetrabutylammonium phosphate monobasic(1.0 mM TBAP), ethylenediaminetetraacetic acid(0.6 mM EDTA) and 2% v/v methanol as the mobile phase. 5% v/v methanol was used as flushing solvent. A reactive ammonia($NH_3$) gas was used to eliminate the potential interference of $ArC^+$. Several Parameters such as solvent ratio, pH, flow rate and sample injection volume were optimized for the successful separation and reproducibility. Although it has been reported thai the separation sensitivity of Cr(III) is superior to that of Cr(VI), the authors observed Cr(VI) was more sensitive than Cr(III) when ammonia($NH_3$) gas was used as the reaction gas. It took less than 3 minutes to analyze chromium species with this method and the estimated detection limits were $0.061\;{\mu}g/L$ for Cr(III) and $0.052\;{\mu}g/L$, for Cr(VI). According to the results from the analysis on chromium species in the raw water of the six intake stations, the concentrations of Cr(III) ranged from 0.048 to $0.064\;{\mu}g/L$(ave. $0.054\;{\mu}g/L$) while that of Cr(VI) ranged from 0.014 to $0.023\;{\mu}g/L$(ave. $0.019\;{\mu}g/L$). Recovery ratio was very high($90.1{\sim}94.1%$). There were two or three times more Cr(III) than Cr(VI) in the raw water.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.768-774
• /
• 2009

To improve the productivity of 1,3-propanediol(1,3-PD) with K. pneumoniae DSM4799 using pure glycerol and crude glycerol derived from the biodiesel process, optimizing fermentation conditions was performed by changing environmental factors such as anaerobic/aerobic condition, temperature, glycerol concentration, and pH. When anaerobic conditions were maintained, there was an improved 1,3-PD production compared with that from aerobic/anaerobic 2-stage fermentation. From the results with temperature $26{\sim}37^{\circ}C$, the higher 1,3-PD production yield was observed at $30{\sim}33^{\circ}C$. For an initial glycerol concentration higher than 60 g/L, cell growth and 1,3-PD production were inhibited. When crude glycerol was used, the initial 1,3-PD production appeared to be inhibited. After 48 hr of incubation, however, 1,3-PD production with crude glycerol was even higher than that with pure glycerol, demonstrating the feasibility of 1,3-PD production using crude glycerol as a substrate. Fed-batch fermentation was applied for the high concentration of 1,3-PD without substrate inhibition. By regulating pH at 7 during the fed-batch with glycerol lower than 40 g/L, the yield of 1,3-PD was 25% higher than that without pH regulation(0.56 g/g vs. 0.45 g/g). In conclusion, based on our results, anaerobic conditions, temperature at $30^{\circ}C$, pure or crude glycerol lower than 40 g/L, and pH regulation at 7 were the optimized conditions for 1,3-PD production using K. pneumoniae DSM4799, making it more feasible to produce 1,3-PD at higher concentration and a lower price.

• Korean Journal of Microbiology
• /
• v.42 no.1
• /
• pp.40-46
• /
• 2006

Galactose joined to glucose by a $\beta(1\rightarrow4)$ glycosidic bond makes lactose and this disaccharide is rich in milk. It is known that lacotse is hydrolyzed to each monomeric sugar by either lactase in human or $\beta-galactosidase$ in bacteria. Ingestion of milk by lactase-deficient persons causes a temporary diarrhea and subsequent chronic diarrhea results in colitis with chronic inflammation. We isolated a $\beta-galactosidase$ producing psycrotolerant strain AS-20 from near cattle shed and investigated the growth at various temperature conditions. Whereas Escherichia coli strains did not grow at $10^{\circ}C$, the AS-20 strain could grow well at this low temperature and showed optimal growth at $30^{\circ}C$. The isolated strain was identified as 97% Hafnia alvei by biochemical properties. This strain could ferment glucose, lacotse, maltose, mannitol, xylose, ONPG, rhamanose and L-arabinose, and decarboxylate lysin and ornithine. To confirm the identity of isolated strain we amplified 16S rDNA by PCR and searched similarity of the 1426 bp DNA sequcence with Genbank database. The strain AS-20 showed 99% similarity with Hafnia alvei. The activity of $\beta-galactosidase$ was 1.5 times higher when the cell was grown at 10 or $20^{\circ}C$ than at $30^{\circ}C$. The highest enzyme activity of AS-20 was also much higher than that of E. coli, which was grown at $30^{\circ}C$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.6
• /
• pp.229-236
• /
• 2014

A stoichiometric mixture of evaporating materials for $MnAl_2S_4$ single crystal thin films was prepared from horizontal electric furnace. To obtain the single crystal thin films, $MnAl_2S_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperatures were $630^{\circ}C$ and $410^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The temperature dependence of the energy band gap of the $MnAl_2S_4$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)=3.7920eV-5.2729{\times}10^{-4}eV/K)T^2/(T+786 K)$. In order to explore the applicability as a photoconductive cell, we measured the sensitivity (${\gamma}$), the ratio of photocurrent to dark current (pc/dc), maximum allowable power dissipation (MAPD) and response time. The results indicated that the photoconductive characteristic were the best for the samples annealed in S vapour compare with in Mn, Al, air and vacuum vapour. Then we obtained the sensitivity of 0.93, the value of pc/dc of $1.10{\times}10^7$, the MAPD of 316 mW, and the rise and decay time of 14.8 ms and 12.1 ms, respectively.

• KSBB Journal
• /
• v.21 no.6 s.101
• /
• pp.466-473
• /
• 2006

Impaired insulin secretion from pancreatic beta-cells in response to glucose is an important feature in the pathology of non-insulin-dependent diabetes mellitus (NIDDM). In the course of screening for useful insulin secretagogues, we have isolated and identified YHB-2017 (Genistein) as a insulin secretion potentiator from fermentation broths of our in-house microbial library. The insulinotropic activity of YHB-2017 in isolated rat pancreatic islets was exerted only at high concentration of glucose (8.3-16 mM) but not at low concentration of glucose (3.3-5.5 mM). Also, in perifusion study with isolated rat pancreatic islets, YHB-2017 stimulated insulin secretion in a time-dependent manner when YHB-2017 was added to KRB buffer containing 16 mM glucose. In the presence of $200\;{\mu}M$ diazoxide and 35 mM KCI, which stimulates maximum $Ca^{2+}$ influx independently of KATP channel, YHB-2017 enhanced KATP channel-independent insulin secretion at high concentration glucose (16 mM). To elucidate the mechanisms of the glucose-dependent potentiation effect of YHB-2017, pharmacologic inhibitors for protein kinase A, protein kinase C and calcium/calmodulin kinase II were pre-treated and then the potentiation effect of YHB-2017 on insulin secretion was investigated. Pre-treatment of H89 as a PKA inhibitor had a significant inhibitory effect on YHB-2017-induced potentiation effect. Furthermore, western immunoblotting analyses revealed that YHB-2017 increased phosphorylation of PKA substrates and cAMP response element-binding protein (CREB) under high concentration of glucose. These results demonstrated that the insulinotropic effect of YHB-2017 is mediated through PKA signal pathway and activated amplifying $K_{ATP}$ channel-independent insulin secretion pathway.

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.256-262
• /
• 2011

Amine can undergo irreversible reactions by $O_{2}$ and high temperature in amine scrubbing process and these phenomena are called "degradation". Degradation causes not only a loss of valuable amine, but also operational problems such as foaming, corrosion and fouling. In this study, using various chemical absorbents(MEA; monoethanolamine, AMP; 2-amino-2-methyl-1-propanol, DAM; 1,8-diamino-p-menthane), we examined the following variable. I) loading ratio of $CO_{2}$ at $50^{\circ}C$ and $120^{\circ}C$, ii) concentration variation and initial degradation rate constant of absorbent in $CO_{2}$ and $CO_{2}/O_{2}$ system, and iii) effect of degradation by $O_{2}$. The $CO_{2}$ loading of 20 wt% DAM was 400% and 270% higher than that of 20 wt% MEA and AMP at 50, respectively and was the largest the difference of $CO_{2}$ loading between absorption $(50^{\circ}C)$ and regeneration $(120^{\circ}C)$ condition. The initial degradation rate constant of 20 wt% DAM was $2.254{\times}10^{-4}cycle^{-1}$ which was slower than that of MEA $(2.761{\times}10^{-4}cycle^{-1})$ and AMP $(2.461{\times}10^{-4}cycle^{-1})$ in $CO_{2}$ system. Also, it was increased 30% by $O_{2}$ that effects on the degradation by $O_{2}$ was less than 100% increased. these degradation reactions was able to identify by formation of new peak in GC and FT-IR spectrum analysis.

• Korean Journal of Microbiology
• /
• v.48 no.4
• /
• pp.314-318
• /
• 2012

Most types of collagen used for biomedical applications, such as cell therapy and tissue engineering, are derived from animal tissues. Therefore, special precautions must be taken during the production of these proteins in order to assure against the possibility of the products transmitting infectious diseases to the recipients. The ability to remove and/or inactivate known and potential viral contaminants during the manufacturing process is an ever-increasingly important parameter in assessing the safety of biomedical products. The purpose of this study was to evaluate the efficacies of the 70% ethanol treatment and pepsin treatment at pH 2.0 for the inactivation of bovine viruses during the manufacture of collagen type I from bovine hides. A variety of experimental model viruses for bovine viruses including bovine herpes virus (BHV), bovine viral diarrhea virus (BVDV), bovine parainfluenza 3 virus (BPIV-3), and bovine parvovirus (BPV), were chosen for the evaluation of viral inactivation efficacy. BHV, BVDV, BPIV-3, and BPV were effectively inactivated to undetectable levels within 1 h of 70% ethanol treatment for 24 h, with log reduction factors of ${\geq}5.58$, ${\geq}5.32$, ${\geq}5.11$, and ${\geq}3.42$, respectively. BHV, BVDV, BPIV-3, and BPV were also effectively inactivated to undetectable levels within 5 days of pepsin treatment for 14 days, with the log reduction factors of ${\geq}7.08$, ${\geq}6.60$, ${\geq}5.60$, and ${\geq}3.59$, respectively. The cumulative virus reduction factors of BHV, BVDV, BPIV-3, and BPV were ${\geq}12.66$, ${\geq}11.92$, ${\geq}10.71$, and ${\geq}7.01$. These results indicate that the production process for collagen type I from bovine hides has a sufficient virus-reducing capacity to achieve a high margin of virus safety.

• Journal of Chest Surgery
• /
• v.37 no.1
• /
• pp.1-10
• /
• 2004

Background: Currently, the cardiopulmonary machine with non-pulsatile pumps, which are low in internal circuit pressure and cause little damage to blood cells, is widely used. However, a great number of experimental studies shows that pulsatile perfusions are more useful than non-pulsatile counterparts in many areas, such as homodynamic, metabolism, organ functions, and micro-circulation. Yet, many concerns relating to pulsatile cardiopulmonary machines, such as high internal circuit pressure and blood cell damage, have long hindered the development of pulsatile cardiopulmonary machines. Against this backdrop, this study focuses on the safety and effectiveness of the pulsatile cardiopulmonary machines developed by a domestic research lab. Material and Method: The dual-pulsatile cardiopulmonary bypass experiment with total extracorporeal circulation was conducted on six calves, Extracorporeal circulation was provided between superior/inferior vena cava and aorta. The membrane oxygenator, which was placed between the left and right pumps, was used for blood oxygenation. Circulation took four hours. Arterial blood gas analysis and blood tests were also conducted. Plasma hemoglobin levels were calculated, while pulse pressure and internal circuit pressure were carefully observed. Measurement was taken five times; once before the operation of the cardiopulmonary bypass, and after its operation it was taken every hour for four hours. Result: Through the arterial blood gas analysis, PCO2 and pH remained within normal levels. PO2 in arterial blood showed enough oxygenation of over 100 mmHg. The level of plasma hemoglobin, which had total cardiopulmonary circulation, steadily increased to 15.87 $\pm$ 5.63 after four hours passed, but remained below 20 mg/㎗. There was no obvious abnormal findings in blood test. Systolic blood pressure which was at 97.5$\pm$5.7 mmHg during the pre-circulation contraction period, was maintained over 100 mmHg as time passed. Moreover, diastolic blood pressure was 72.2 $\pm$ 7.7 mmHg during the expansion period and well kept at the appropriate level with time passing by. Average blood pressure which was 83$\pm$9.2 mmHg before circulation, increased as time passed, while pump flow was maintained over 3.3 L/min. Blood pressure fluctuation during total extracorporeal circulation showed a similar level of arterial blood pressure of pre-circulation heart. Conclusion: In the experiment mentioned above, pulsatile cardiopulmonary machines using the doual-pulsatile structure provided effective pulsatile blood flow with little damage in blood cells, showing excellence in the aspects of hematology and hemodynamic. Therefore, it is expected that the pulsatile cardiopulmonary machine, if it becomes a standard cardiopulmonary machine in all heart operations, will provide stable blood flow to end-organs.