• Journal of Microbiology and Biotechnology
• /
• v.11 no.2
• /
• pp.326-328
• /
• 2001

Pseudomonas diminuta (ATCC 19146) has been typically used in the bacterial challenge test for validation of the sterilizing filtration process. Cell size is critical for determining the retention characteristics of membrane filters with pore-size of $0.2{\mu}m$. The changes of cell sizes after osmotic shocks at 150, 260, 500, and 700 mosM were measured by a particle size analyzer and the changes of their buoyant densities were analyzed with a Percoll gradient. The results indicated that there were no significant differences when cells were cultured in 260 mosM medium and osmotically shocked at 500 and 700 mosM. However, the osmotically shocked cells at 150 mosM showed a 38% increase of the cell size compared to the cells at 260 mosM. From these study, we concluded that the worst case condition for validation of a sterilizing filter would be 500 mosM, not because of changes in the cell size, but due to decrease in cell viability under those conditions.

• Journal of the Korean Society of Visualization
• /
• v.21 no.3
• /
• pp.49-56
• /
• 2023

The Polymer electrolyte membrane fuel cell (PEMFC) operates at ambient temperature as a low-temperature fuel cell. During its operation, voltage losses arise due to factors such as operating conditions and material properties, effecting its performance. Computational simulations of fuel cells can be categorized into 1D simulation and CFD, chosen based on their specific application purposes. In this study, we carried out an analysis validation using 1D geometry and compared its performance with the results from 2D geometry analysis. CFD allows for the representation of pressure, velocity distribution, and fuel mass fraction according to the geometry, enabling the analysis of current density. However, the 1D simulation, simplifying governing equations to reduce time cost, failed to accurately account for fuel distribution and changes in fuel concentration due to fuel cell operations. As a result, it showed unrealistic results in the cell voltage region dominated by concentration loss compared to CFD.

• Journal of Korean Society on Water Environment
• /
• v.32 no.1
• /
• pp.52-59
• /
• 2016

This study investigated the occurrences and succession patterns of harmful cyanobacteria, as well as environmental factors, during a 3-year period (September 2012 to August 2015) in the upper region of the Nakdong River around Sangju weir. A total of 27 cyanobacterial taxa were observed in this study, and classified into 26 species and 1 variety belonging to 11 genera, 5 families, and 3 orders. Cell density ranged from 24 to 42,001 cells/ml, with a geometric mean of 33 cells/ml, during the survey period. The dominant orders differed depending on the survey year; order Oscillatoriales in 2013, Chroococcales in 2014 and Nostocales in 2015. An Aphanizomenon bloom occurred in June 2015 at which time the highest cell density of 36,873 cells/ml was detected in the upper region of the Nakdong River, where as the Aphanizomenon spp. cell density (190-1,704 cells/ml) had been low prior to that time. An Aphanizomenon bloom also occurred at around the same time downstream in the Young River, a major inflow branch of the Nakdong River. The Aphanizomenon cell density along the Nakdong River increased markedly after joining of the YoungRiver, indicating that the Aphanizomenon bloom in the YoungRiver caused a bloom in the Nakdong River. Meteorological and environmental parameters, such as very low precipitation, higher water temperature, pH, and TP concentration, and lower TN/TP ratio, in May and June of 2015 than in 2013 and 2014 exerted marked effects on the Aphanizomenon bloom in June 2015 in the Young River.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.6
• /
• pp.498-504
• /
• 2008

Metal-reducing bacterium, Geobacter sulfurreducens is available for mediator-less microbial fuel cell (MFC) because it has biological nanowires(pili) which transfer electrons to outside the cell. In this study, in the anode chamber of the MFC system using G. sulfurreducens, the concentrations of NaCl, sodium phosphate and sodium bicarbonate as electrolytes were mainly optimized for the generation of electricity from acetate. 0.4%(w/v) NaClO and 0.5M $H_2SO_4$ could be utilized for the sterilization of acrylic plates and proton exchange membrane (major construction materials of the MFC reactor), respectively. When NaCl concentration in anode phosphate buffer increased from 5 to 50 mM, power density increased from 6 to $20\;mW/m^2$. However, with increasing sodium phosphate buffer concentration from 5 to 50 mM, power density significantly decreased from 18 to $1\;mW/m^2$. Twenty-four mM sodium bicarbonate did not affect electricity generation as well as pH under 50 mM phosphate buffer condition. Optimized anode chamber of MFC using G. sulfurreducens generated relatively high power density ($20\;mW/m^2$) with the maximum coulombic efficiency (41.3%).

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_3
• /
• pp.1289-1295
• /
• 2023

Polyurethane foam insulation required for storing and transporting cryogenic liquefied gas is already widely used as a thermal insulation material for commercial LNG carriers and onshore due to its stable price and high insulation performance. These polyurethane foams are reported to have different mechanical performance depending on the density, and the density parameter is determined depending on the amount of the blowing agent. In this study, density-dependent polyurethane foam was fabricated by adjusting the amount of blowing agent. The mechanical properties of polyurethane foam were analyzed in the room temperature and cryogenic temperature range of -163℃ at 1.5 mm/min, which is a quasi-static load range, and the cells were observed through microstructure analysis. The characteristics of linear elasticity, plateau, and densification, which are quasi-static mechanical behaviors of polyurethane foam, were shown, and the correlation between density and mechanical properties in a cryogenic environment was confirmed. The correlation between mechanical behavior and cell size was also analyzed through SEM morphology analysis. Polyurethane foam with a density of 180 kg/m³ had a density about twice as high as that of a polyurethane foam with a density of 96 kg/m³, but yield strength was about 51% higher and cell size was about 9.5% smaller.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1213-1214
• /
• 1995

The advantages for using fuel cell instead of storages for powering electric vehicles are as follows : the energy density of fuel cell is greater than that of battery, fuel cell can be recharged much faster than battery. The objectives of this study are to investigate the status of Fuel Cell Vehicle technologies.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.10
• /
• pp.981-985
• /
• 2007

We present a MEMS-based portable Direct Methanol Fuel Cell (micro-DFMC), featured by a platinum sputtered microcolumn electrode and a built-in fuel chamber containing a limited amount of methanol fuel. Also presented is a micro-DMFC stack structure having a common electrolyte sandwiched by the microcolumn electrodes. The single cells with ME16 and PE16 electrodes show the maximum power densities of $31.04{\pm}0.29{\mu}W/cm^2$ and $9.75{\pm}0.29{\mu}W/cm^2$, respectively; thus indicating the microcolumn electrode (ME16) generates the power density (3.2 times) higher than the planar electrode (PE16). The single cell tests of ME16 and ME4 electrodes (Fig.8) show the maximum power of $31.04{\pm}0.29{\mu}W/cm^2$, and $25.23{\pm}2.7{\mu}W/cm^2$, respectively; thus demonstrating the increased window frame reduces the normalized standard power deviation (standard deviation over the average power). The normalized deviation of 0.11 in ME4 cell has been reduced to 0.01 in ME16 cell due to the increased window frames. The maximum power density of 4-cell stack is 15.7 times higher than that of the single cell. 4-cell stack produces the power capacity of 20.3mWh/g during 980min operation at the voltage of 450mV with the load resistance of $800{\Omega}$.

• KSBB Journal
• /
• v.14 no.3
• /
• pp.264-272
• /
• 1999

Benzoylformate was converted to benzaldehyde by whole cell enzyme from Pseudomonas putida KCTC 1751. We investigated the effect of the composition of the growth medium on th accumulation of benzoylformate decarboxylase in the microbial cell. We prepared a calcium alginate capsule containing Pseudomonas putida cells to develop a reusable whole cell enzyme. Pseudomonas putida cells were inoculated in the capsule and cultured in M1 medium for 1 day followed by cultivation in M3 medium for 3 days. The dry cell density reached 77.75 g/L on the basis of the inner volume of the capsule. The specific activity of encapsulated whole cell benzoylformate decarboxylase was half as high as that of free whole cell enzyme. The activity of encapsulated whole cell benzoylformate decarboxylase was half as high as that of free whole cell enzyme. The activity of encapsulated whole cell benzoylformate decarboxylase decreased 20 % after use for 20 batches and 40% after use for 30 batches. The dry cell density reduced about 10 % after 30 trials.

• Korean Journal of Ichthyology
• /
• v.10 no.1
• /
• pp.115-127
• /
• 1998

The digestive tract of the rockfish, Sebastes schlegeli composed of pharynx, esophagus, stomach, intestine, anus and ten or eleven pyloric caeca. Pyloric caeca is blind sac of banana shape, and that is originated from pyloric portion of the stomach. The relative length of gut(RLG), that is length of digestive tract to standard length, is about 1.56(n=10). Esophageal muscularis consists of thin outer layer of longitudinal muscle and thick inner layer of circular muscle. Mucosal epithelium consists of columnar epithelium with short microvilli and contains numerous mucous secretory cell. The mucosal folds of the stomach are regular, and the muscularis consists of longitudinal, oblique and circular muscle layer. The chief cell of the gastric gland have a tubular mitochondria, endoplasmic reticula and numerous secretory granules in electron-dense. However, parietal cell contains small mitochondria, endoplasmic reticula and vacuoles in low electron density. Mucosal epithelium of the pyloric caeca and intestine composed of columnar epithelium, goblet cell, rodlet cell and dark cell. Columnar absorptive cell in the pyloric caeca and intestine contains well developed mitochondria, endoplasmic reticula, vesiculated granules in high electron density, pinocytotic vesicles and multivesicular body. Rodlet cell have a well developed cytoplasmic capsule and the endoplasmic reticula in the cytoplasm. Dark cell showing a high electron density in the cytoplasm and contains well developed mitochondria. Columnar epithelium of the intestine have a well developed intercellular junction and the microvilli which contains actin filament originated from the cytoplasm. Mucosal epithelium of the intestine have a longer microvilli and more abundant goblet cells than in the pyloric caeca.

• Korean Journal of Animal Reproduction
• /
• v.24 no.4
• /
• pp.451-455
• /
• 2000

Gene targeting are very useful tools for the research on the gene function in vivo, mass production of foreign materials and biomedical approach of therapeutic process. But this process is very complicated and necessary highly skilled technique, because it is very different from ES cell origin, genetic background of embryo, and experimental conditions. We investigated the productivity ability of chimeric mouse after aggregation with TT2 ES cells. Increse of ES cell density caused gradual decrease in embryo development in vitro and in th $\varepsilon$ production of chimeric mice in vivo. One million ES cell density for the aggregation was very efficient to produce high percentage chimeric mice in their coat color. These results suggested that appropriate cell density plays a key role in the development and production of chimeric mice by a 8-cell aggregation method.