• 한국융합학회논문지
• /
• 제13권3호
• /
• pp.197-202
• /
• 2022

CZTS 태양전지는 Cu, Zn, Sn, Se, S으로 구성된 흡수층을 사용하는 박막 태양전지로, In, Ga이 사용되는 CIGS 태양전지보다 저렴하며 Pb, Cd이 사용된 페로브스카이트, CdTe 태양전지보다 친환경적이다. 본 연구에서 우리는 유연기판인 Mo foil 위에 제작된 유연 CZTS 태양전지를 지정된 곡률만큼 휘게 하는 bending test를 진행하였다. 태양전지에 압축응력이 가해지는 inner benidng과 인장응력이 가해지는 outer bending의 방향에서 실험은 진행되었으며, 50 mmR의 곡률 반경으로 진행된 1,000 회의 굽힘 횟수 동안 태양전지의 효율은 최고 12.7%까지 감소하였으며, 두 방향 모두에서 효율 감소의 가장 큰 원인은 병렬저항의 큰 감소로 나타났다.

• 한국표면공학회지
• /
• 제38권3호
• /
• pp.112-117
• /
• 2005

In this paper, CdS thin films, which were widely used as a window layer of the CdS/CdTe and the $CdS/CuInSe_2$heterojunction solar cell, were grown by chemical bath deposition, and the structural, optical and electrical properties of the films on reaction temperatures were investigated. Cadmium acetate and thiourea were used as cadmium and sulfur source, respectively. And Ammonium acetate was used as the buffer solution. As the reaction temperatures were increased, the deposition rate of CdS fllms prepared by CBD was increased and the grain size was large due to increasing reaction rate in solution, also optical transmittance of the films in visible lights was increased on rising reaction temperatures.

• 한국진공학회지
• /
• 제8권3B호
• /
• pp.297-301
• /
• 1999

High quality CdTe single crystal for the solar cell fabrication was grown by vertical Bridgman method. The etch pits patterns of {111} surfaces of CdTe etched by Nakagawa solution was observed the {11} A composed of Cd atoms with typical triangle etch pits of pyramid mode. From the photoluminescence measurement of {111} A, we observed free exciton $(E_x)$ existing only high quality crystal and neutral acceptor bound exciton ($A^{\circ}$, X) having very strong peak intensity. Then, the full width at half maximum and binding energy of neutral acceptor bound exciton were 7 meV and 5.9 meV, respectively. By Haynes rule, and activation energy of impurity was 59meV. Therefore, the origins on impurity level acting as a neutral acceptor were associated Ag or Cu elements.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2010년도 춘계학술대회
• /
• pp.805-808
• /
• 2010

본 연구에서는 CdTe 및 $CuInSe_2$ 태양전지의 광투과층으로 사용되는 CdS 박막을 chemical bath deposition으로 제조하고, 반응용액의 온도에 따른 미세구조의 변화를 조사하였다. CdS 박막의 결정구조와 미세구조는 기판의 종류에 큰 변화 없이 $85^{\circ}C$ 까지는 반응용액의 온도가 증가함에 따라 기판에서의 ion-by-ion 성장이 촉진되어 CdS 박막의 성장률이 증가하며, 결정성이 향상되고 continuous하면서 매우 조밀한 미세구조를 가졌다. 그러나 온도가 $55^{\circ}C$ 이하의 경우 CdS 형성에 필요한 Cd2+ 이온의 공급이 느려져 온도에 따라 증착률이 감소하였다. 또한 핵생성 위치 수가 감소하여 입자의 크기가 증가하였고, 박막 내부에는 void가 형성되어 균일하지 못한 미세구조를 나타내었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.321.2-321.2
• /
• 2013

CdS는 2.42 eV의 밴드 갭을 가지는 직접 천이형 반도체로서 CdTe계와 CGIS계 태양전지의 접합 partner로 많이 이용되어 왔다. 태양전지의 광투과층으로 사용되는 CdS 박막의 필요한 물성으로는 높은 광투과도와 얇은 두께이다. 광투과층으로 사용되는 CdS 막의 광투과도가 높아야 많은 양의 빛이 손실 없이 투과하여 광흡수층인 CIGS에 도달할 수 있다. 특히, CdS막의 두께가 얇으면 밴드 갭 이상의 에너지를 가지는 파장의 빛도 투과시킬 수 있어 태양전지의 효율의 증가을 얻을 수가 있다. 그러나 CdS 막의 두께가 얇을 경우, pinhole이 생성되는 등 막의 균질성이 문제가 되기 때문에 얇으면서도 pinhole이 없는 CdS 박막을 만들기 위한 연구가 진행되고 있다. 본 연구에서는 높은 변환 효율을 갖는 CIGS 박막 태양전지 제작에 적합한 chemical bath depostion(츙)법을 이용하여 CdS 박막을 제조하였다. 또한 반응온도, Cd 및 S source 비, 반응용액의 pH와 같은 증착 조건에 따른 박막의 구조적, 광학적 특성을 조사하였다.

• 한국전기전자재료학회논문지
• /
• 제14권2호
• /
• pp.104-110
• /
• 2001

Structural, optical and electrical properties of Cd$_{1-x}$ Zn$_{x}$S films deposited by chemical bath deposition(CBD), which is a very attractive method for low-cost and large-area solar cells, are presented. Especially, in order to control more effectively the zinc component of the films, zinc acetate, which was used as the zinc source, was added in the reaction solution after preheating the reaction solution and the pH of the reaction solution decreased with increasing the concentration of zinc acetate. The films prepared after preheating and pH control had larger zinc component and higher optical band gap. The crystal structures of Cd$_{1-x}$ Zn$_{x}$S films was a wurtzite type with a preferential orientation of the (002) plane and the lattice constants of the films changed from the value for CdS to those for ZnS with increasing the mole ratio of the zinc acetate. The minimum lattice mismatch between Cd$_{1-x}$ Zn$_{x}$S and CdTe were 2.7% at the mole ratio of (ZnAc$_2$)/(CdAc$_2$+ZnAc$_2$)=0.4. As the more zinc substituted for Cd in the films, the optical transmittance improved, while the absorption edge shifted toward a shorterwavelength. the photoconductivity of the films was higher than the dark conductivity, while the ratio of those increased with increasing the mole ratio of zinc acetate. acetate.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1436-1438
• /
• 1997

In this paper, CdS thin films, which were widely used window layer of the CdS/CdTe and the CdS/$CuInSe_2$ heterojunction solar cell, were grown by chemical bath deposition, and The properties were investigated in detail. Cadmium acetate and thiourea were used as cadmium and sulfur source, respectively. And Ammonium acetate was used as the buffer solution. Also Ammonia was used for controlling pH concentration. The reaction velocity was increased with increasing reaction temperature and decreasing pH concentration. The crystal structure of CdS films grown with various pH concentration had the hexagonal structure with (002) plane peak. In the range of pH $9{\sim}9.5$, the intensity of the peak was highest, and as increasing pH concentration, decreased the intensity of the peak except pH12.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.35.1-35.1
• /
• 2011

New photovoltaic (PV) materials and manufacturing approaches are needed for meeting the demand for lower-cost solar cells. The prototypal thin-film photovoltaic absorbers (CdTe and $Cu(In,Ga)Se_2$) can achieve solar conversion efficiencies of up to 20% and are now commercially available, but the presence of toxic (Cd,Se) and expensive elemental components (In, Te) is a real issue as the demand for photovoltaics rapidly increases. To overcome these limitations, there has been substantial interest in developing viable alternative materials, such as $Cu_2ZnSnS_4$ (CZTS) is an emerging solar absorber that is structurally similar to CIGS, but contains only earth abundant, non-toxic elements and has a near optimal direct band gap energy of 1.4~1.6 ev and a large absorption coefficient of ${\sim}10^4\;cm^{-1}$. The CZTS absorber layers are grown and investigated by various fabrication methods, such as thermal evaporation, e-beam evaporation with a post sulfurization, sputtering, non-vacuum sol-gel, pulsed laser, spray-pyrolysis method and electrodeposition technique. In the present work, we report an alternative method for large area deposition of CZTS thin films that is potentially high throughput and inexpensive when used to produce monolithically integrated solar panel modules. Specifically, we have developed an aqueous chemical approach based on chemical bath deposition (CBD) with a subsequent sulfurization heat treatment. Samples produced by our method were analyzed by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, absorbance and photoluminescence. The results show that this inexpensive and relatively benign process produces thin films of CZTS exhibiting uniform composition, kesterite crystal structure, and good optical properties. A preliminary solar cell device was fabricated to demonstrate rectifying and photovoltaic behavior.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.99.1-99.1
• /
• 2012

The thin-film photovoltaic absorbers (CdTe and $Cu(In,Ga)Se_2$) can achieve solar conversion efficiencies of up to 20% and are now commercially available, but the presence of toxic (Cd,Se) and expensive elemental components (In, Te) is a real issue as the demand for photovoltaics rapidly increases. To overcome these limitations, there has been substantial interest in developing viable alternative materials, such as $Cu_2ZnSnS_4$ (CZTS) is an emerging solar absorber that is structurally similar to CIGS, but contains only earth abundant, non-toxic elements and has a near optimal direct band gap energy of 1.4 - 1.6 eV and a large absorption coefficient of ~104 $cm^{-1}$. The CZTS absorber layers are grown and investigated by various fabrication methods, such as thermal evaporation, e-beam evaporation with a post sulfurization, sputtering, non-vacuum sol-gel, pulsed laser, spray-pyrolysis method and electrodeposition technique. In the present work, we report an alternative aqueous chemical approach based on chemical bath deposition (CBD) method for large area deposition of CZTS thin films. Samples produced by our method were analyzed by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, absorbance and photoluminescence. The results show that this inexpensive and relatively benign process produces thin films of CZTS exhibiting uniform composition, kesterite crystal structure, and some factors like triethanolamine, ammonia, temperature which strongly affect on the morphology of CZTS film.

• 한국재료학회지
• /
• 제30권10호
• /
• pp.566-572
• /
• 2020

In the recent years, thin film solar cells (TFSCs) have emerged as a viable replacement for crystalline silicon solar cells and offer a variety of choices, particularly in terms of synthesis processes and substrates (rigid or flexible, metal or insulator). Among the thin-film absorber materials, SnS has great potential for the manufacturing of low-cost TFSCs due to its suitable optical and electrical properties, non-toxic nature, and earth abundancy. However, the efficiency of SnS-based solar cells is found to be in the range of 1 ~ 4 % and remains far below those of CdTe-, CIGS-, and CZTSSe-based TFSCs. Aside from the improvement in the physical properties of absorber layer, enormous efforts have been focused on the development of suitable buffer layer for SnS-based solar cells. Herein, we investigate the device performance of SnS-based TFSCs by introducing double buffer layers, in which CdS is applied as first buffer layer and ZnMgO films is employed as second buffer layer. The effect of the composition ratio (Mg/(Mg+Zn)) of RF sputtered ZnMgO films on the device performance is studied. The structural and optical properties of ZnMgO films with various Mg/(Mg+Zn) ratios are also analyzed systemically. The fabricated SnS-based TFSCs with device structure of SLG/Mo/SnS/CdS/ZnMgO/AZO/Al exhibit a highest cell efficiency of 1.84 % along with open-circuit voltage of 0.302 V, short-circuit current density of 13.55 mA cm^-2, and fill factor of 0.45 with an optimum Mg/(Mg + Zn) ratio of 0.02.