• Transactions of Materials Processing
• /
• v.13 no.3
• /
• pp.230-235
• /
• 2004

A new design based on the appropriate geometry of molded part and type of runner system under the optimal processing conditions was proposed to minimize the micro weld lines on the sub deco surface molded by two shot molding. Theoretical and experimental studies were conducted to examine the cause of the weld lines during the overmolding process in two shot molding. Various dimensions and geometries of substrate$(1^{st}shot)$ and the wall thickness of overmold$(2^{nd}shot)$ have been proposed to avoid the weld lines which are the most inevitable appearance defects occurred on the sub deco. The each design proposal was analyzed by mold flow analysis after part modeling. The analysis results were compared with molded part from mass production tool. It could be seen that from the analysis that the proper geometry of plastic part and type of runner system considering pressure drop under the optimal processing conditions were the most influential factors to avoid weld lines occured on the sub deco.

• ALGAE
• /
• v.20 no.4
• /
• pp.315-324
• /
• 2005

Anatomical organization of Stoechospermum marginatum reveals small cortical cells with moderately dense cytoplasm, overlying a multilayered medulla comparatively poor in cytoplasmic contents. The anticlinal walls of cortical cells show local thickenings rich in alginic acids. Sori form on both thallus surfaces and show tetrasporangia, paraphyses and sterile-cells. The unicellular paraphyses are rich in sulphated polysaccharides whereas multicellular ones have abundance of not only polysaccharides, but also of vacuoles and phenols. The sterile-cells are modified cortical cells present on either side of the tetrasporangium and bear cytoplasmic strands towards soral cavity. Various stages of tetrasporogenesis are seen in a single sorus. The developing tetrasporangium shows a two layered wall, where the outer one is rich in alginic acid and inner has sulphated polysaccharides. An apical pad aids tetraspore release. Also involved in the release process are sterile-cells, paraphyses and polysaccharides.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.153-159
• /
• 2007

The performance of a direct-injection type diesel engine often depends on the strength of air flow in the cylinder, shape of combustion chamber, the number of nozzle holes, etc. This is of course because the process of combustion in the cylinder was affected by the mixture formation process. In the present paper, high speed photography was employed to investigate the effectiveness of holes penetrated from the bottom of cavity wall to piston crown for some more useful utilization of air. The holes would function to improve mixing of fuel and air by the increase of air flow in the cylinder. The results obtained are summarized as follows, (1) Activated first of the combustion by shorten of ignition timing and rapid flame propagation (2) Raised the combustion peak pressure, more close to TDC the formation timing of peak pressure.

• Journal of Chest Surgery
• /
• v.10 no.1
• /
• pp.164-172
• /
• 1977

This is a report of a case in which a left atrial myxoma was successfully removed by total cardiopulmonary bypass with total hemodilution and moderate hypothermia. The patient was a 17 old girl with mitral valvular symptoms that occured suddenly three months prior to operation. After the onset of symptoms. it was progressively aggravated to serious general condition. The preoperative diagnosis of left atrial tumor was made from echocardiography. and the tumor was confirmed as myxoma by the histopathological examination of the tumor tissue removed during operation. The myxoma was unusually originated from posterior wall of the left atrium. which was located between drainage orifices of right and left pulmonary veins, The tumor developed in the left atrial cavity and one of the polypoid processes of the myxoma was prolapsed into the the left ventricle through the mitral orifice. Following operation. there was no evidence for peripheral vascular embolism, and all valvular symptoms disappeared. The postoperative course was uneventful.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.2
• /
• pp.81.1-81.1
• /
• 2014

We utilized a 2-D PDR code developed by Lee et al. (2014) to explore the observed OH line fluxes toward embedded protostars. This 2-D PDR code combines self-consistently the FUV radiative transfer, gas-energetics, chemistry, and line radiative transfer. We modeled two sources, GSS30-IRS1 and Elias29, which show conspicuous line emission in the Herschel/PACS wavelength range. The physical and chemical structure for a given embedded source was derived by fitting the PACS CO line fluxes. After exploring various parameter spaces, we conclude that IR-pumping effect either by the central IR source and dust in-situ is insignificant for OH emission, unlike previous studies. We here present a possible solution for the observed OH fluxes, which require a high OH abundance and temperature at the inner-part of the UV heated cavity wall.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.112-117
• /
• 2000

A numerical study on natural convection in a vertical square cavity filled with a porous medium is carried out with Brinkman-Forchheimer-extended Darcy flow model, and the validity of local thermodynamic equilibrium assumption is studied. The local thermodynamic equilibrium refers to the state in which a single temperature can be used to describe a heat transfer process in a multiphase system. With this assumption, the analysis is greatly simplified because only one equation is needed to describe the heat transfer process. But prior to using this assumption, it is necessary to know in what conditions the assumption can be used. The numerical results of this study reveal that large temperature difference between fluid phase and solid phase exists near wall region, paticularily when the convection becomes dominant over conduction. And the influence of flow parameters such as fluid Rayleigh number, fluid Prandtl number, dimensionless particle diameter and conductivity ratio are investigated.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.5
• /
• pp.85-90
• /
• 2011

In this paper a design procedure via computer-aided molding simulation is presented to optimize the air-trap locations in a speaker encloser of mobile phone. The molding flow simulation reveals that the race-tracking phenomenon is the dominant feature in the current mold design. In obtaining an optimal filling pattern, the local modifications of the wall thickness such as in a flow leader attachment are considered as the primary control factor, and both the gate position and the filling time become the secondary control factor. In the one-at-a-time approach, the last location to be filled in the mold cavity could be successfully moved to the extremities of the part, allowing a natural ventilation of entrapped air through the mold parting plane.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.652-657
• /
• 2000

In this paper, Firstly, it is shown that the high vibration source of piping system is the pulsation transmission of pipe line element, such as, orifice plate, valves and the control valve is a broad band source and the branch wall and the cavity have vortex frequency. Secondly, in order to decrese the high vibration of piping system, some practical Friction damper with high damping have been developed and its effectiveness is investigated as installing it at piping system practically.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1823-1828
• /
• 2000

Power transformers, air-intakes, stacks in a combined thermal power plant are the main noise sources. Power transformer noise among them has being get a target of public complaint due to 480Hz component of its pure tone. The source is mainly magnetostrictive vibration of the transformer core. The first countermeasures was installing sound barrier on the front of transformer. However, 500Hz, center of the frequency is not reduced. This paper includes the measurements of noise level at the near resident apartment, the identification of noise transfer and the countermeasures for noise sources. Cavity resonance type of noise reduction devices was installed on enclosuring wall of transformers. As a result, the noise level from transformer is reduced about 3dB.

• Journal of Welding and Joining
• /
• v.20 no.4
• /
• pp.484-490
• /
• 2002

The formation and stability of stationary laser weld keyholes were investigated using a numerical simulation. The effect of multiple reflections in the keyhole was estimated using the ray tracing method, and the free surface profile, flow velocity and temperature distribution were calculated numerically. In the simulation, the keyhole was formed by the displacement of the melt induced by evaporation recoil pressure, while surface tension and hydrostatic pressure opposed cavity formation. A transition mode having the geometry of the conduction mode with keyhole formation occurred between the conduction and keyhole modes. At laser powers of 500W and greater, the protrusion occurred on the keyhole wall, which resulted in keyhole collapse and void formation at the bottom. Initiation of the protrusion was caused mainly by collision of upward and downward flows due to the pressure components, and Marangoni flow had minor effects on the flow patterns and keyhole stability.bility.