• 농업과학연구
• /
• 제23권1호
• /
• pp.13-24
• /
• 1996

널말뚝을 이용하여 연약지반을 굴착할 때 굴착단계에 따른 지반의 변위 변형 및 안정성을 분석하여 다음과 같은 결론을 얻었다. 1. 수평방향의 변위는 버팀대 설치전에는 굴착면 상부에서 크게 나타났으나, 버팀대 설치 후는 굴착저면의 아래쪽으로 이동되면서 집중되는 현상을 나타냈다. 2. 버팀대 설치후에 널말뚝의 변위는 설치 전보다 1/2정도로 급격히 감소함을 나타냈고, 지반의 안정한 굴착깊이의 한계는 2단 버팀대 설치후는 GL-8.0m정도로 나타났다. 3. 최대전단변형은 굴착깊이에 따라 점차로 증가하였고, 또 굴착저면에서 나타나는 전단변형에 의한 국부적인 파괴가능성은 버팀대로 보강함으로써 감소시킬 수 있었다. 4. GL-7.5m에서 널말뚝의 최대수평변위는 탄소성법에서는 굴착깊이의 0.2%, 유한요소법에서는 0.6%로 나타났으며, 굴착저면부근에서 최대변위를 나타냈다. 5. 해석모델지반에서 근입깊이에 대한 안전성을 확보하기 위해서는 버팀대 1단 설치의 경우는 D/H가 0.89이상, 2단설치의 경우는 D/H가 0.77이상이 될수 있도록 근입깊이를 확보하여야 할 것으로 판단된다. 6. 근입깊이에 대한 안전율과 D/H와의 관계에서 버팀대 1단 설치의 경우는 Fs = 0.736(D/H) + 0.54, 버팀대 2단 설치의 경우는 Fs = 0.750(D/H) + 0.62의 관계식을 나타냈다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제4권4호
• /
• pp.423-436
• /
• 2012

Unstiffened plates are integral part of all kinds of structures such as ship and offshore oil platforms. Openings are unavoidable and absolutely reduce the ultimate strength of structures. In this study, the finite element analysis package, ABAQUS, is used to analyze the behavior of unstiffened plate with rectangular opening. The rectangular opening form is divided into two cases. In case1, opening depth is constant, but opening width is varied. Meanwhile, in case2 opening width is fixed and opening depth is varied. Besides, for the two different form opening, the effect of plate slenderness parameter (${\beta}$), opening area ratio (AR) and opening position ratio (PR) on the ultimate strength of plate with opening under axial compression are presented. It has been found that the ultimate strength of plate ofcase1is much more sensitive to the plate slenderness parameter (${\beta}$) and opening area ratio (AR) than that of case2. However, for case1, opening position (PR) almost has no effect on the ultimate strength, whereas, regardingcase2, the influence of opening position (PR) depends on the plate slenderness parameter (${\beta}$). Based on nonlinear regression analysis, three design formulae are not only developed but also approved reasonably for the practical engineering design.

• Journal of Periodontal and Implant Science
• /
• 제38권1호
• /
• pp.103-108
• /
• 2008

Purpose: Studies reported controversial results about prognosis of root resection with 0%-38% failure rate. The purpose of this study is to consider clinical efficacy of root resection. Materials and Methods: This study reported three cases of root resection which were performed on different sites. In first case, lower right first molar showed pus discharge and 7 mm of probing pocket depth. It was diagnosed as fracture of mesial root. Hemisection of mesial root was performed. In second case, upper right first molar showed severe bone loss on disto-buccal root and 7 mm of probing pocket. Resection of disto-buccal root was performed In third case, lower left second molar showed severe bone loss on distal root including apex and 15mm of probing pocket depth. Hemisection of distal root was performed. Result: In these three cases of root resection, compromised molars were treated successfully and conserved. Conclusion: Root resection is a successful procedure treating compromised multi-rooted teeth and conserving teeth when proper case selection is performed.

• 유통과학연구
• /
• 제22권4호
• /
• pp.105-114
• /
• 2024

Purpose : Due to the uncertainty of the global trade environment and the trade downturn, the shipping industry continues to face challenges. This study aims to investigate in-depth analysis of crisis overcoming strategies through case study of a company that is leader in the shipping and logistics industry. Research Desigh and Methodology : In order to conduct an in-depth analysis, a single case analysis was selected as a qualitative study. For this purpose, various secondary sources were used, and indirect interview data were also used. In this study, Maersk was selected because it has grown from a traditional shipping logistics company to a digital platform company. Results: Maersk has transformed itself into a comprehensive, digital logistics platform with several key strategies to respond to the long-term slump in the shipping industry. First, it leveraged Maersk's diversification and portfolio optimization strategy. Second, Maersk is transforming its logistics and transport processes through digitalization and technological innovation. Conclusion: Maersk, which is responding to the long-term recession facing the shipping industry, looked at how it has leveraged its strengths and explored new opportunities through a number of strategies and changes. This study provides insight into a digital logistics platform that will benefit the other companies as well.

• 한국보건간호학회지
• /
• 제10권1호
• /
• pp.12-22
• /
• 1996

Currently. exchanges of industrial workers between countries are more active than ever. and the problem of AIDS in connection with the operation of preventive educational programs has reached a point where the issue cannot be limited to native people alone any more. Based on such judgement. this research has been carried out to provide basic study materials by grasping the latent factors representing the difference between countries in the levels of right knowledge. attitude and behavior with respect to AIDS maintained by workers who have grown in different social and cultural living background. During the period from Apr. 1. 1995 to Jun. 30. questionnaires. written both in Korean and English, were distributed to Korean and Malaysian employees working at certain Korean video manufacturers. and the results of replies. given by 80 workers who were analyzed through matched sampling· method where ages and sex matched by country. were used as the research materials. The gathered materials were analyzed through the SPSS package t-test. ANOVA. factor analysis and multiple stepwise regression methods. and the following results were obtained. 1. The 2 extracted latent factors could be named 'common. social' knowledge factor and 'in-depth. psychological' knowledge factor respectively. 2. The percentile points of 'external. social' knowledge factor. in the case of Korean workers. howed 90.0 at average. a figure 13.75 points higher than those of Malaysian workers. 76.25. On the other hand. the percentile points of the 'in-depth. psychological'knowledge factor showed 70.80 at average in the case of Korean workers. a figure 7.47 points lower than those of Malaysian workers. 78.33. Meanwhile. the difference in percentile points between the 2 latent factors was 8.54 at average. indicating that the points of 'in-depth. psychological' knowledge factor was lower than those of the 'external. social' knowledge factor. 3. As for Korean workers. the percentile points of the 'in-depth. psychological' knowledge factor showed higher points in office workers than in non-office workers. and such variables exhibited in the position of workers can explain the $7\%$ of the latent factor. The percentile points of the 'in-depth. psychological' knowledge factors. in the case of Malaysian workers. showed higher points in groups who had religion than in groups who did not. and higher points in groups who obtained information from newspapers than in groups who obtained from televisions or other sources; and with these 2 variables. $26\%$ of this latent factor can be explained. The results. of analysis described so far suggest that while Korean workers possessed general level of knowledge on AIDS. they had low level of practical knowledge as far as its depth is concerned. and that they had social prejudice on patients as well as on the AIDS infection route. In addition. because the overall knowledge level of Malaysian workers. is lower than that of Korean workers. it suggests that separate programs intended for Malaysian workers are required prior to executing integrated programs.

• 한국안전학회지
• /
• 제15권2호
• /
• pp.111-117
• /
• 2000

In this study, the bearing capacity behavior of strip footing located above a continuous cavity in sand was investigated experimentally. The model footing test was performed in a model box made by using raining method in sand. The model footing test results were compared with those obtained from theoretically proposed equations. The results of the analysis indicate that there is a critical region under the footing. For strip footing, there exists a critical depth below which the presence of the cavity has negligible influence on the footing performance. Only when the cavity is located within this region will the footing performance be significantly affected by the presence of the cavity. The size of the critical region depends on several factors such as footing shape, soil property, cavity size and cavity shape. When the cavity is located within the critical region, the bearing capacity of the footing varies with various factors, such as the size and location of the cavity and the depth of foundation. Based on the experimental study, the following conclusions were induced. 1. The ultimate bearing capacity due to the eccentricity of a underground cavity increases at the rate of the small rather than that due to the depth of a underground cavity. This indicates that the bearing capacity of a strip footing is influenced on the depth rather than the eccentricity of a underground cavity. 2. The critical $depth(D/B)_{cr}$, by underground cavity in sand soil ground that is made by the relative density($D_r$)=55%, 65%, 75%, approaches a range of about 8~10 in case of W/B=1, and about 11~13 in case of W/B=2. 3. In case of the relative density($D_r$) 75%, the most outstanding differential settlement trend is shown in the depth of 4~8cm regardless of the size of cavity, namely, when the value of D/B is 1~2. Therefore, a underground cavity influences on not only the decrease of the bearing capacity but also the differential settlement of a strip footing.

• 한국수자원학회논문집
• /
• 제50권10호
• /
• pp.681-690
• /
• 2017

본 연구에서는 우리나라 전역에 대하여 인공신경망 기법을 사용하여 일최심신적설을 추정하였다. 인공신경망 모형 구조를 시행 착오법을 이용하여 설계한 결과, 입력자료는 일 최저 기온, 일 평균 기온, 강수량으로 정하였고, 은닉층과 노드의 수는 각각 1층, 10개로 정하였다. 관측값을 인공신경망의 입력자료로 활용하는 경우, 교차검증 상관계수는 0.87로 Ordinary Kriging기법을 활용하여 일최신심적설을 공간보간한 경우의 교차검증상관계수인 0.40보다 크게 높았다. 미계측 지역의 일최심신적설을 추정하는 경우의 인공신경망 모형의 성능을 알아보기 위하여 인공신경망 모형의 입력자료들을 Ordinary Kriging으로 공간보간하여 일최심신적설을 추정하였다. 이 경우 교차검증 상관계수는 0.49였다. 또한 해발 고도 200 m 이상의 산지에서의 인공신경망의 성능은 나머지 지역인 평지에서의 성능보다 다소 떨어짐을 확인하였다. 본 연구의 이러한 결과는 우리나라 전역에 걸친 정확한 적설량의 즉각적인 산정에 인공신경망 모형이 효과적으로 활용될 수 있음을 의미한다.

• 한국농공학회지
• /
• 제17권4호
• /
• pp.3991-4000
• /
• 1975

It is the aim of this study to investigate the influence of the factors in the sprayer nozzle for the travelling distance and to get nozzle design data in relation to the nozz1e with and without swirl plate. The factors of sprayer nozzle are composed of the spraying pressure, the helical angle of swirl plate, the helical groove depth of swirl plate, the distance of vortex chamber the slope of nozz1e cap, the curvature of nozzle cap and the hole diameter of nozz1e cap. The travelling distance and the size of sprayed particle are experimeted indoors by the factorial arrange-ment according to the 5 each level of the above factors. The results of this stupy are summarized as follows; 1. In the nozzle with swirl p1ate there were remarkable significance among factors each other, while without swirl plate were no significance. 2. The helical angle and groove depth in the nozzle with swirl plate were the highest effective factors. The effect of helical angle was very remarked in the quadratic curve with minium value. 3. The correlation betweenthe travelling distance and the sprayed particle size was no high and under 250 micron in the case with swirl plate, and there was higher correlation in the case without swirl plate. 4. The new ideal development of the swirl plate using of the most effective helical angle and groove depth will probably show the possiblities to make effective travelling distance over 8 meters and more over and to make average particle diameter under 300 micron.

• Journal of Welding and Joining
• /
• 제15권3호
• /
• pp.79-87
• /
• 1997

This study was performed to evaluate basic characteristics of electron beam welding process for a 9% Ni steel plate. The principal welding process parameters, such as working distance, accelerating voltage, beam current and welding speed were investigated. The AB (Arata Beam) test method was also applied to characterize beam size and energy density of the electron beam welding process. The electron beam size was found to decrease with the increase of accelerating voltage and the decrease of working distance. So, in case of high voltage (150kV), spot size and energy density of electron beam were revealed to be 0.9mm and $6.5\times10^5W/\textrm{cm}^2$ respectively. The accelerating voltage among the welding parameters was found to be the most important factor governing the penetration depth. When the accelerating voltage of electron beam was low ($\leq$90kV), beam current and welding speed did not affect on the penetration depth significantly. However, in case of high voltage ($\geq$120kV), the depth of penetration increased very sensitively with the increase of beam current and the decrease of welding speed.

• 소성∙가공
• /
• 제18권6호
• /
• pp.465-470
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. The effect of surface roughness of cylinder liner on the friction coefficient was analyzed. This study provided tribological data of hard and soft piston ring coatings against cylinder liner. The surface roughness does exert an influence on the average friction coefficient, with smoother surfaces generally yielding lower friction coefficients. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics such as, scratch depth, width, pile-up height and elastic modulus.