• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.50-50
• /
• 2008

ZnO has been extensively studied for optoelectronic applications such as blue and ultraviolet (UV) light emitters and detectors, because it has a wide band gap (3.37 eV) anda large exciton binding energy of ~60 meV over GaN (~26 meV). However, the fabrication of the light emitting devices using ZnO homojunctions is suffered from the lack of reproducibility of the p-type ZnO with high hall concentration and mobility. Thus, the ZnO-based p-n heterojunction light emitting diode (LED) using p-Si and p-GaN would be expected to exhibit stable device performance compared to the homojunction LED. The n-ZnO/p-GaN heterostructure is a good candidate for ZnO-based heterojunction LEDs because of their similar physical properties and the reproducibleavailability of p-type GaN. Especially, the reduced lattice mismatch (~1.8 %) and similar crystal structure result in the advantage of acquiring high performance LED devices with low defect density. However, the electroluminescence (EL) of the device using n-ZnO/p-GaN heterojunctions shows the blue and greenish emissions, which are attributed to the emission from the p-GaN and deep-level defects. In this work, the n-ZnO:Ga/p-GaN:Mg heterojunction light emitting diodes (LEDs) were fabricated at different growth temperatures and carrier concentrations in the n-type region. The effects of the growth temperature and carrier concentration on the electrical and emission properties were investigated. The I-V and the EL results showed that the device performance of the heterostructure LEDs, such as turn-on voltage and true ultraviolet emission, developed through the insertion of a thin intrinsic layer between n-ZnO:Ga and p-GaN:Mg. This observation was attributed to a lowering of the energy barriers for the supply of electrons and holes into intrinsic ZnO, and recombination in the intrinsic ZnO with the absence of deep level emission.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.93-93
• /
• 1999

양자점(Quantum dot : QD)를 이용한 소자를 만들기 위해서는 수직방향으로의 적층이 필수적이다. 양자점의 적층은 수직적으로 같은 위치에 정렬하므로, 고려되어야 할 요소로는 양자점간의 파동함수의 중첩(coupling)에 의한 특성변화, 적층의 진행에 따른 변형(strain)의 증가로 기인되는 volcano 모양으로 나타나는 결함등이 있다. 이러한 결함은 nonradiative recombination center로 작용하여 오히려 효율이 떨어지게 되는 현상이 발생하게 되므로 본 연구에서는 적층횟수에 따른 발광효율의 변화를 조사하여 소자응용에 적절한 적층 조건을 조사하였다. 시료성장은 molecular beam epitaxy (MBE) 장치를 이용하여 GAs(100) 기판위에 GaAs buffer를 58$0^{\circ}C$에서 150nm 성장후 InAs/GaAs 양자점과 50$0^{\circ}C$에서 적층회수 1, 3, 6, 10, 15, 20회로 하였으며 적층성장 이후 GaAs cap layer를 성장하였다. GaAs spacing과 cap layer의 성장온도 역시 50$0^{\circ}C$이며 시료의 분석은 photoluminescence (PL)과 scanning transmission electron microscope (STEM)으로 하였다. 적층횟수를 바꾸어 시료를 성장하기 전에 적층횟수를 10회로 고정하고 spacing 두께를 2.8nm, 5.6nm, 11.2nm로 바꾸어 성장하여 PL 특성을 관찰하여본 결과 spacing이 2.8nm인 경우 수직적으로 정렬된 양자점 간에 coupling이 매우 커서 single layer QD의 PL peak에 비해 약 100nm 정도 파장이 증가하였고, spacing의 두께가 11.2nm 일 경우는 single layer QD와 거의 같은 파장의 빛을 방출하여 중첩이 거의 일어나지 않지만 두꺼운 spacing때문에 PL세기가 감소하였다. 한편, 적층회수에 따른 광학적 특성을 PL로 조사하여 본 결과 peak 파장은 적층횟수가 1회에서 3회로 증가했을 때는 blue shift 하다가 이후 적층이 증가함에 따라 red shift 하였다. 그리고 10층 이상의 적층에서는 excited state에서 기인된 peak이 검출되었다. 이렇나 원인은 적층수가 증가함에 따라 carrier life time이 증가하여 exciter state에 carrier가 존재할 확률이 증가하기 때문으로 생각된다. 또한 PL 세기가 다소 증가하다가 10층 이상의 경우는 다시 감소함을 알 수 있었다. 반치폭도 3층과 6층에서 가장 적은 값을 보였다. 이와 같은 결과는 결함생성과 관련하여 STEM 분석으로 해석되어질 수 있는데 6층 적층시는 양자점이 수직적으로 정렬되어 잘 형성됨을 관찰할 수 있었고 적층에 따른 크기 변화도 거의 나타나지 않았다. 그러나 10층 15층 적층시 몇가지 결함이 형성됨을 볼수 있었고 양자점의 정렬도 완전하게 이루어지지 않음을 볼 수 있었다. 그러므로 수직적층된 InAs 양자점의 광학적 특성은 성장조건에 따른 결함생성과 밀접한 관련이 있으며 상세한 논의가 이루어질 것이다.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.1
• /
• pp.9-13
• /
• 2002

Recently, Organic electroluminescent devices (OELDs) have been demonstrated the medium sized full color display with effective multi-layer thin films. In this study, the multi-layer OELDs were prepared on the patterened ITO (indium tin oxide)/glass substrates by the vacuum thermal evaporation method. The low molecule compounds such as $Alq_3$(trim-(8-hydroxyquinoline)aluminum) and CTM (carrier transfer material) as the electron transport and injection layers as well as TPD (triphenyl-diamine) and CuPc (copper phthalocyanine) as the hole transport and injection layers were used. The luminance was rapidly increased above the threshold voltage of 10 V. The luminance and emission spectrum for the OELDs samples with $A1/CTM/Alq_3$/TPD/1TO structures were found to be 430 cd/$m^2$and 512 nm at 17 V showing green color emission. In contrast, the samples with $Li-A1/Alq_3$/TPD/CuPC/1TO multi-structures showed 508 nm in emission spectrum and 650 cd/$m^2$at 17 V in the luminance. The increment of luminance may be ascribed to the improved efficiency of recombination in the region of the emission layers by the deposition of CuPc as hole injection layer and the low work function of the Li-Al electrode compared to the Al electrode.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.430-430
• /
• 2012

The surface recombination velocity of the silicon solar cell could be reduced by passivation with insulating layers such as $SiO_2$, SiNx, $Al_2O_3$, a-Si. Especially, the aluminium oxide has advantages over other materials at rear surface, because negative fixed charge via Al vacancy has an additional back surface field effect (BSF). It can increase the lifetime of the hole carrier in p-type silicon. The aluminium oxide thin film layer is usually deposited by atomic layer deposition (ALD) technique, which is expensive and has low deposition rate. In this study, ICP-assisted reactive magnetron sputtering technique was adopted to overcome drawbacks of ALD technique. In addition, it has been known that by annealing aluminium oxide layer in nitrogen atmosphere, the negative fixed charge effect could be further improved. By using ICP-assisted reactive magnetron sputtering technique, oxygen to nitrogen ratio could be precisely controlled. Fabricated aluminium oxy-nitride (AlON) layer on silicon wafers were analyzed by x-ray photoelectron spectroscopy (XPS) to investigate the atomic concentration ratio and chemical states. The electrical properties of Al/($Al_2O_3$ or $SiO_2/Al_2O_3$)/Si (MIS) devices were characterized by the C-V measurement technique using HP 4284A. The detailed characteristics of the AlON passivation layer will be shown and discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.308-309
• /
• 2016

Reducing surface recombination is a critical factor for high efficiency silicon solar cells. The passivation process is for reducing dangling bonds which are carrier. Tunnel oxide layer is one of main issues to achieve a good passivation between silicon wafer and emitter layer. Many research use wet-chemical oxidation or thermally grown which the highest conversion efficiencies have been reported so far. In this study, we deposit ultra-thin tunnel oxide layer by PECVD (Plasma Enhanced Chemical Vapor Deposition) using $N_2O$ plasma. Both side deposit tunnel oxide layer in different RF-power and phosphorus doped a-Si:H layer. After deposit, samples are annealed at $850^{\circ}C$ for 1 hour in $N_2$ gas atmosphere. After annealing, samples are measured lifetime and implied Voc (iVoc) by QSSPC (Quasi-Steady-State Photo Conductance). After measure, samples are annealed at $400^{\circ}C$ for 30 minute in $Ar/H_2$ gas atmosphere and then measure again lifetime and implied VOC. The lifetime is increase after all process also implied VOC. The highest results are lifetime $762{\mu}s$, implied Voc 733 mV at RF-power 200 W. The results of C-V measurement shows that Dit is increase when RF-power increase. Using this optimized tunnel oxide layer is attributed to increase iVoc. As a consequence, the cell efficiency is increased such as tunnel mechanism based solar cell application.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.413-413
• /
• 2016

태양전지 제작 시 에미터층을 형성하는 도핑 공정의 최적화는 캐리어 수집 확률 증가와 함께 결정질 실리콘 태양전지 고효율화를 위해 매우 중요하다. 본 연구에서는 결정질 실리콘 태양전지 다이오드의 다양한 도핑 공정으로 제작된 p-n 접합에 대한 전기적 특성 분석을 진행하였다. 도핑 공정의 경우 선 증착-후 확산 공정 시간과 가스량을 변화시켜 다양한 에미터층을 제작하였다. 선 증착 시간 변화를 주는 경우 선 증착 공정을 $825^{\circ}C$로 고정한 뒤 시간을 7분에서 17분까지 변화하고 후 확산 공정을 $845^{\circ}C$, 14분으로 고정하였다. 후 확산 시간 변화를 주는 경우는 선 증착 공정을 $825^{\circ}C$, 12분으로 고정한 뒤 후 확산 공정을 $845^{\circ}C$로 고정 하고 시간을 9분에서 19분까지 변화시켰다. 선 증착 공정을 $845^{\circ}C$ 12분, 후 확산 공정을 $845^{\circ}C$, 14분으로 고정 한 뒤 선 증착 시 POCl3양을 400 ~ 1400 SCCM까지 변화시켰고, 후 확산 시 산소량을 0 ~ 1000 SCCM까지 가변한 조건에서 에미터층에 대한 특성을 분석하였다. 결과적으로 선 증착 공정 $825^{\circ}C$ 12분, 후 확산 공정 $845^{\circ}C$ 14분에서 SCR(Space Charge Region)에서 3.81의 가장 낮은 이상 계수 값을 나타내었다. 이는 p-n접합의 내부결함이 줄어들어 태양전지의 캐리어 수명이 증가됨을 보였다. 선 증착 공정 중 $POCl_3$ 주입량 800 SCCM, 후 확산 공정 중 산소량 400 SCCM에서 $15.9{\mu}s$로 가장 높은 캐리어 수명을 나타내었다. Suns-VOC 측정 결과 $POCl_3$ 주입량 800 SCCM, 산소량 400 SCCM에서 619mV로 가장 높은 개방전압을 얻을 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.157-158
• /
• 2013

Organic solar cell was fabricated using one-pot deposition of a mixture of NiO nanoparticles, P3HT and PCBM. In the presence of NiO, the photovoltaic performance was slightly increased comparing to that of the device without NiO. When $TiO_2$ thin films with a thickness of 2~3 nm was prepared on NiO nanoparticles using atomic layer deposition, the power conversion efficiency was increased by a factor 2.5 with respect to that with bare NiO. Moreover, breakdown voltage of the film consisting of NiO, P3HT, and PCBM on indium tin oxide was increased by more than 1 V in the presence of $TiO_2$-shell on NiO nanoparticles. It is evidenced that S atoms of P3HT can be oxidized on NiO surfaces, and $TiO_2$-shell on NiO nanoparticles. It is evidenced that S atoms of P3HT can be oxidzed on NiO surfaces, and $TiO_2$ shell heavily reduced oxidation of S at oxide/P3HT interfaces. Oxidized S atoms can most likely act as carrier generation sites and recombination centers within the depletion region, decreasing breakdown voltage and performance of organic solar cells. Our result shows that fabrication of various core-shell nanostruecutres of oxides by atomic layer deposition with controlled film thickness can be of potential importance for fabricating highly efficient organic solar cells.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.10
• /
• pp.1092-1097
• /
• 2009

A novel exopolysaccharide named Ebosin was produced by Streptomyces sp. 139, with medicinal activity. Its biosynthesis gene cluster (ste) has been previously identified. For the functional study of the ste7 gene in Ebosin biosynthesis, it was disrupted with a double crossover via homologous recombination. The monosaccharide composition of EPS-7m produced by the mutant strain Streptomyces sp. 139 ($ste7^-$) was found altered from that of Ebosin, with fucose decreasing remarkably. For biochemical characterization of Ste7, the ste7 gene was cloned and expressed in Escherichia coli BL21. With a continuous coupled spectrophotometric assay, Ste7 was demonstrated to have the ability of catalyzing the transfer of fucose specifically from GDP-$\beta$-L-fucose to a fucose acceptor, the lipid carrier located in the cytoplasmic membrane of Streptomyces sp. 139 ($ste7^-$). Therefore, the ste7 gene has been identified to code for a fucosyltransferase, which plays an essential role in the formation of repeating sugars units during Ebosin biosynthesis.

• Korean Journal of Materials Research
• /
• v.8 no.7
• /
• pp.591-595
• /
• 1998

In this work, the freestanding GaN single crystalline substrates without cracks were grown by hydride vapor phase epitaxy (HVPE) and its some properties were investigated. The GaN substrate, having a current maximum size of 350 $\mu\textrm{m}$-thickness and 100$\textrm{mm}^2$ area, were obtained by HVPE growth of thick film GaN on sapphire substrate and subsequent mechanical removal of the sapphire substrate. A lattice constant of $C_o$= 5.18486 $\AA$ and a FWHM of DCXRD was 650 arcsec for the single crystalline GaN substrate. The low temperature PL spectrum consist of three excitonic emission and a deep D- A pair recombination at 1.8eV. The Raman E, (high) mode frequency was 567$cm^{-1}$ which was the same as that of strain free bulk single crystals. The Hall mobility and carrier concentration was 283$cm^3$<\ulcornerTEX>/ V.sand 1.1$\times$$10^{18}cm^{-3}$, respectively.

• Journal of the Korean Vacuum Society
• /
• v.15 no.3
• /
• pp.301-307
• /
• 2006

We have investigated optical properties of p-modulation doped In(Ga)As quantum dots (QDs) on InP substrate with a comparison with the undoped QDs. Photoluminscence (PL) intensity of doped QDs at 10 K was about 10 times weaker than that of undoped QD sample. The decay time of doped QD sample at its PL peak, obtained from the time-resolved PL (TR-PL) experiment at 10 K, was very fast compared to that of undoped sample. We interpret that this fast decay time of the doped QD sample comes from the addition of non-radiative recombination paths, which are originated from the doping-related defects.