• Journal of the Korean Society of Safety
• /
• v.26 no.4
• /
• pp.41-46
• /
• 2011

The purpose of this paper is to analyze the causes of accidents related to the 3 phase 170 kV gas insulated switchgear of a power system collected from accident sites to secure data for the prevention of similar accidents and provide important points of view regarding diagnosis for the prevention of accidents involving gas insulated switchgears. The analysis results of the causes of accidents involving gas insulated switchgears showed deformation of the manipulation lever installed at the S-phase, disconnection of the insulation rod connection, melting of the upper conductor, a damaged tulip, damage to the lower spacer and the spacer at the breaker, etc. It is believed from this result that the potential for accidents has expanded due to accumulated energy as a result of repeated deterioration. The carbonization depth of a GIS was formed near the screw (T2, T3) used to secure the lower pole of the S-phase tulip. It is not known what has caused the screws to be extruded and melted. However, it is thought that an unbalanced electromagnetic force, micro-discharge, surface discharge, etc., have occurred at that point. In addition, even though 16 years have passed since its installation, there was no installation defect, act of arson, accidental fire, etc. General periodical inspection and diagnosis failed to find the factors causing the accidents. As a system contained in a closed metal container, it has a high risk factor. Therefore, it is necessary to design, install and operate a GIS in accordance with the standard operational procedure (SOP). In addition, it is necessary to apply conversion technology for periodical SF6 gas analysis and precision safety diagnosis. It is expected that tracking and managing these changes in characteristics by recording the results on the history card will provide a significant accident prevention effect.

• Korean Chemical Engineering Research
• /
• v.60 no.3
• /
• pp.439-445
• /
• 2022

In this study, Silicon and petroleum pitch were coated on the surface of Si/C fiber manufactured using electrospinning to improve the electrochemical performances. SiO₂/PAN fiber was prepared by electrospinning with TEOS and PAN at various ratios dissolved in DMF. The characteristics of carbonization, reduction, and pitch coating processes were investigated for the optimal process of the pitch coated Si/C fiber anode composite. Anode composite prepared with TEOS/PAN = 4/6 (CR-46) after carbonization and reduction process has a capacity of 657 mAh/g. To improve capacity and stability, Si powder and PFO pitch were coated at the surface of CR-46. When the pitch composition was fixed at 10 wt%, it was found that the capacity increased as the weight ratio of silicon increased, but the stability decreased. The pitch coated Si/C fiber composite with 10 wt% silicon has high capacity of 982.4 mAh/g and capacity retention of 86.1%. In the test to evaluate rate performance, the rate capability was 80.2% (5C/0.1C).

• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.3
• /
• pp.302-314
• /
• 2015

There is an adsorption method using activated carbon as a typical method for removing elemental mercury. Physical characteristics of activated carbon such as specific surface area and volume of pore (micro and meso) have positive effect for mercury adsorption. Activated carbon is carbon-based material with a high specific surface area. This activated carbon can be manufactured through carbonization and activation process. In this process, physical characteristics of specific surface area and pore distribution are changed by controlling operating parameters like temperature, time and reagent of activation. In this study, we evaluated characteristics of activated carbons manufactured from pinewood and coal with the operating parameters. We evaluated mercury adsorption capacities of the activated carbons having excellent physical characteristics and compared those to the commercial activated carbon.

• Applied Chemistry for Engineering
• /
• v.19 no.4
• /
• pp.439-444
• /
• 2008

The oyster shell adsorbents were prepared by steam activation method to evaluate their adsorption characteristics. Washed and pulverized waste oyster shells were prepared by steam activated process in converter at the temperature range of about $700{\sim}800^{\circ}C$ after carbonized at the range of $600{\sim}1000^{\circ}C$. The shell carbonized at $1000^{\circ}C$ showed the best performance among those of other temperature ranges. Also, comparison between gas and liquid phase adsorption was performed to verify adsorbent possibility of waste shell. In case of gas phase, the adsorbent showed lower performance than existing commercial adsorbents. On the other hand, the liquid phase, they showed similar adsorption performance to commercial adsorbents when benzene was used.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.6
• /
• pp.31-42
• /
• 2007

To investigate the pyrolytic and anatomical characteristics of Korean softwood, Pinus densi-flora, Pinus rigida and Larix leptolepis, and hardwood, Acer palntatum, Fraxinus rhynchophylla and Quercus variabilis, chemical components analysis, TG-DTA (Thermogravimetric Analysis & Differential Thermal Analysis), MBA (Methylene Blue Adsorption) test and SEM observation were carried out. For TG-DTA, samples were carbonized up to $800^{\circ}C$ at the heating rate of $10^{\circ}C$/min under $N_2$ flows 1 l/min using thermogravimetric analyzer. Chemical component analysis of all samples resulted in typical contents of major wood component. In TG-DTA results, softwood showed higher char yield than hardwood, and lignin displayed the highest char yield among the major wood components. All samples showed typical TGA, DTG and DTA curves for wood pyrolysis except a few differences between softwood and hardwood. Content of lignin influenced its pyrolysis characteristics, while molecular structure of lignin affected not only the weight loss but also the yield of char. In MBA test results, MBA of softwoods was higher than that of hardwoods. Char of Pinus densiflora showed the highest MBA, but its degree was lower than activated carbon or fine charcoal about 23 and 4 times, respectively. SEM observation showed carbonization process preserves wood structure and retain the micro-structure of wood fibers.

• Journal of Energy Engineering
• /
• v.9 no.4
• /
• pp.279-287
• /
• 2000

코크스 오븐에서 석탄 건류과정 중에 발생하는 석탄 중심의 가스압 특성에 대한 장입탄 수분, 가열속도 및 일반탄 배합비의 영향을 조사하기 위해 이동벽이 있는 pilot 규모의 코크스 오븐(0.45mW$\times$0.1mH$\times$1.2mL)에서 석탄 건류 실험을 수행하였다. 석탄 중심에서의 가열속도가 상업용 코크스 오븐과 비슷한 건류조건에서 장입탄 수분을 감소시켰을 때, 수분 증발 이후 가열속도는 비슷하였으며, 건류 초기 수증기압은 크게 증가하였고, 석탄 중심에서의 가스압은 습탄에 비해 대략 2.5배 증가하였다. 석탄 중심에서의 가열속도가 상업용 코크스 오븐보다 훨씬 빠른 건류조건에서 장입탄 수분을 감소시켰을 때, 수분 증발 이후 가열속도는 크게 감소하였고, 건류 초기 수증기압은 크게 증가하였으며, 석탄중심에서의 가스압은 습탄에 비해 대략 2배 증가하였다. 석탄 가열속도가 상업용 오븐보다 빠른 건류조건에서 장입탄에 일반탄을 첨가하여 일반탄 배합비를 증가시켰을 때 배합탄 중심에서의 가스압은 현저히 감소하였다.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.850-852
• /
• 1998

SiC thin film have been prepared by ICP-CVD for low temperature deposition and large area deposition. The structural properties of deposited SiC films are characterized by employing SEM, FT-IR, XRD, XPS and Raman Spectroscopy. From the experimetal results, good crystallinity has been achieved in $1000^{\circ}C$ grown SiC film which have carbonization step at $1100^{\circ}C$ for substrate bias of 30V.

• Carbon letters
• /
• v.20
• /
• pp.32-38
• /
• 2016

In this study, cellulose nanoplates (CNPs) were fabricated using cellulose nanocrystals obtained from commercial microcrystalline cellulose (MCC). Their pyrolysis behavior and the characteristics of the product carbonaceous materials were investigated. CNPs showed a relatively high char yield when compared with MCC due to sulfate functional groups introduced during the manufacturing process. In addition, pyrolyzed CNPs (CCNPs) showed more effective chemical activation behavior compared with MCC-induced carbonaceous materials. The activated CCNPs exhibited a microporous carbon structure with a high surface area of 1310.6 m²/g and numerous oxygen heteroatoms. The results of this study show the effects of morphology and the surface properties of cellulose-based nanomaterials on pyrolysis and the activation process.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.4
• /
• pp.51-55
• /
• 2000

The woodceramics which are new porous carbon materials were obtained by carbonizing from thinned small log of Aomori HIBA (Thujopsis dolabrata S. et. Z. var. hondae M.) impregnated with phenol resin in a vacuum furnace. During the carbonization process, the resin changes into glassy carbon, which has superior property. The resin impregnation rate and bending strength depend on the types of board and density. In this paper, the manufacturing method of woodceramics made from thinned small logs of Aomori HIBA was introduced and some properties were examined.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.1507-1510
• /
• 2009

In this study, Batch Test was carried out on the adsorption abilities to heavy metal of FWC, which occurred during the carbonization process was part of recycling methods of food waste. The heavy metals used in the experiment were lead and cadmium; mixing its solution with carbonized ratio of 50:1, respectively. The different concentrations were applied with 50, 100, 200, 400, and $800\;{\mu}g/m{\ell}$. When, the initial concentration is less than 200mg/l, there has been a high removal ratio of 20% to 50%. Comparing the test results on Lanmmuir and Freundlich adsorption isotherms, the Freundilich adsorption isotherm was well compatible.