• Journal of Sensor Science and Technology
• /
• v.22 no.3
• /
• pp.175-180
• /
• 2013

This paper describes the characteristics of cubic silicon carbide (3C-SiC) films grown on a carbonized Si(100) substrate, using hexamethyldisilane (HMDS, $Si_2(CH_3)_6$) as a safe organosilane single precursor in a nonflammable $H_2$/Ar ($H_2$ in Ar) mixture carrier gas by atmospheric pressure chemical vapor deposition (APCVD) at $1280^{\circ}C$. The growth process was performed under various conditions to determine the optimized growth and carbonization condition. Under the optimized condition, grown film has a single crystalline 3C-SiC with well crystallinity, small voids, low residual stress, low carrier concentration, and low RMS. Therefore, the 3C-SiC film on the carbonized Si (100) substrate is suitable to power device and MEMS fields.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.1
• /
• pp.1-7
• /
• 2004

This paper describes the carbonization characteristics of a phenolic resin deteriorated by tracking under the environment of a fire. In the experiment, a liquids droplet of 1[％] NaCl was dripped on the phenolic resin to cause a tracking with 110[V], 220[V] voltages applied. It can be addressed from the experimental results that when an insulator is carbonized by an external fire, its structure is amorphous. If an insulator is carbonized by electrical cause, on the other hand, its structure would be crystalline. In order to observe the surface change of the phenolic resin, the tracking process was analyzed by using SEM. In the case that the materials are carbonized under heat or fire, the exothermic peak appears around 500[$^{\circ}C$]. This is one of the important factors to determine the cause of fires. As a result of DTA, the exothermic peaks of an untreated sample showed at 333.4[$^{\circ}C$], 495.7[$^{\circ}C$] but those of a sample deteriorated by tracking appeared at 430.6[$^{\circ}C$], 457.6[$^{\circ}C$] in a voltage of 110[V], and at 456.2[$^{\circ}C$], 619.7[$^{\circ}C$] in a voltage of 220[V]. It is possible, therefore, to distinguish a virgin sample from carbonized samples(graphite) by the exothermic peak.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.4
• /
• pp.33-40
• /
• 2002

This research was to investigate the adsorption characteristics of charcoals of major Korean wood species (thinned trees) and wood-based materials. As carbonization time and temperature increased, methylene-blue adsorption (MBA) of charcoals of thinned trees and wood-based materials increased. Pinus koraiensis charcoal showed the highest MBA. MBA of softwoods was higher than that of hardwoods. There was a negative correlation between air-dried specific gravity before carbonization and MBA of carbonized thinned trees. The MBA of wood-based materials showed similar value, but wood-based materials in MBA was lower than thinned woods. Surface area and total pore volume of thinned trees and wood-based materials increased as carbonization temperature increased. The species showing highest MBA appeared to have the highest surface area at the carbonization temperature of 600℃ as well. There was a positive correlation between surface area, total pore volume and MBA of charcoals. The charcoal of wood-based materials generally exhibited micro pores.

• Applied Chemistry for Engineering
• /
• v.20 no.1
• /
• pp.109-115
• /
• 2009

The purposes of this study are to treat sewage sludge that has increasingly become an issue and to recycle it as the adsorbent. The adsorbent was produced by carbonization and simultaneous steam activation, and its characteristics were studied. Parametric screening studies were carried out for the preparation of good adsorbent. Optimum operating conditions were confirmed as input carbonization-activated temperature of $840^{\circ}C$, feed steam flow rate of 70 g/min, carbonization-activated time of 30 min and feed dried sludge of 10.8 kg/day, respectively. At this time, the iodine adsorptivity was maximized as 328.1 mg/g. Pore development, structure, element compound and content were confirmed by using nanoPOROSITY, SEM (Scanning electron microscope), and EDS (Energy dispersive spectroscopy). Through this result, it was known that the adsorbent derived from sewage sludge could be used for the treatment of leachate in a landfill, VOCs (Volatile organic compounds), and so on.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.3
• /
• pp.45-52
• /
• 2007

The anatomical characteristics of Quercus variabilis woods carbonized at 310 to $350^{\circ}C$ were examined with an optical and scanning electron microscopy, and an X-ray diffraction analysis. Dimensional change and weight loss were also investigated. Volume of wood samples decreased with increasing the carbonization temperature, and checks were developed along with radial direction. Vessel diameter in tangential direction showed higher shrinkage than that in radial direction. Weight loss of samples increased with increasing carbonization temperature. Especially, the weight loss rapidly increased at the temperature ranging from 330 to $340^{\circ}C$. SEM study presented that the cell walls of samples carbonized at below $320^{\circ}C$ showed the layering structure. However, it was revealed that the layering structure was disappeared at $330^{\circ}C$ and over and showed an amorphous-like structure without cell wall layering. Interestingly, the existence of cellulose crystalline substance at $340^{\circ}C$ was confirmed by X-ray diffraction analysis and it was not detected at $350^{\circ}C$. Consequently, it is considered that the critical temperature for carbonization of wood was around $350^{\circ}C$.

• Applied Chemistry for Engineering
• /
• v.29 no.6
• /
• pp.765-771
• /
• 2018

In this study, the optimization of carbonization conditions in manufacturing processes was performed to improve the absorption performance of sewage sludge based sorbent used for treating $H_2S$ out of all odorous substances generated by various environmental facilities. Adsorbents applied were manufactured from the sewage treatment plant under different carbonization conditions, such as temperature and heating rate, and the correlation between the adsorption performance and physical properties of the adsorbents was verified. As a result, the adsorption performance of sludge at $900^{\circ}C$ with a heating rate of $10^{\circ}C/min$ was the best, and the SEM and BET analysis revealed that specific surface area and characteristics of pore (size, volume) were major parameters for the adsorption. In addition, the effect of K ions used for improving the adsorption performance of the optimum carbonization condition sorbent was insignificant for the sewage sludge based sorbent.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.1
• /
• pp.35-40
• /
• 2018

Nd:YAG laser was used to carbonize polyimide films to produce carbon films. This is a simple manufacturing process to fabricate low cost sensors. By applying this method, we studied characteristics of flexible and low-cost piezoresistive. Previously, many studies focused on carbonization of polyimide using $CO_2$ laser with wavelength of $10.6{\mu}m$. In this paper, carbonization (carbonization process) was performed on polyimide films using an Nd:YAG laser with a wavelength of $1.064{\mu}m$. In order to increase the resolution, we optimized the laser conditions of the power density ($W/cm^2$) and the beam scan rate. In previous studies using $CO_2$ laser, the minimum line width was $140{\sim}220{\mu}m$ but in this study, carbon line width was reduced to $35{\sim}40{\mu}m$. The initial sheet resistance of the carbon sensor was $100{\sim}300{\Omega}/{\square}$. The resistance decreased by 30% under stretched with a curvature radius of 21 R. The calculated gauge factor was 56.6. This work offers a simple, highly flexible, and low-cost process to fabricate piezoresistive sensors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.42-49
• /
• 2018

In steel industries, cold-rolled sheet manufacturing is one of the links between the front and rear important industries for national competitiveness and high value-added production. In particular, in small and medium-sized enterprises, one of the major problems is the carbonization phenomenon of the steel sheet during the annealing process. Carbonization occurring on the surface of the coil help reduce steel production. After conducting various experiments to identify the cause of carbonization on the surface of a cold-rolled steel, the following results were obtained: (1) An analysis of the rolling oil, which is used in the field, revealed it to contain approximately 40 ppm carbonized material. (2) A comparison of the thermal denaturation characteristics of the fresh rolling oil and using rolling oil by FT-IR analysis showed that thermal denaturation had occurred, as shown by the significant decrease in the relative intensity of the 2900 and $1750cm^{-1}$ peaks. (3) The thermal decomposition of the rolling oil took place for the rolling oil at approximately $220^{\circ}C$. Furthermore, annealing experiments at $200^{\circ}C$ showed that the carbonization phenomenon of the sample was not observed. On the other hand, carbonization was observed at temperatures higher than $240^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.3
• /
• pp.15-21
• /
• 2006

The objective of this research is to develop the technique for carbonization of wood pellet and analyze a possibility for the utilization of carbonized wood pellet. The properties of wood pellet charcoals, such as density, yield, elemental composition, higher heating value, and methyleneblue adsorption, were analyzed. Wood pellet was made of sawdust of Hyunsasi-poplar, Japanese larch, Korean pine, Korean red pine, and Jolcharn-oak (serrate oak), respectively. The high density charcoal ($0.5{\sim}0.7g/cm^3$) was yielded from densified wood pellet. The carbon contents and calorific values of wood pellet charcoals were increased with the increase of carbonization temperature. The methyleneblue adsorptivity of wood pellet charcoal was similar to that of wood charcoal.

• Journal of Korean Society of Water and Wastewater
• /
• v.27 no.6
• /
• pp.743-750
• /
• 2013

In this study, the carbonized aggregate of light weight and high mechanical strength using sewage sludge was evaluated with changing carbonation variables of temperature, detention time and feed condition. Porosity and mechanical strength was simultaneously increased according to increase of carbonization temperature unexpectedly. Carbonization detention time above 1 hour nearly affect on the porosity, but mainly on mechanical strength of the carbonized aggregate in case of clay addition. On $900^{\circ}C$, porosity and mechanical strength was increased rapidly, but above $1000^{\circ}C$, porosity began to decrease. Clay addition was very effective on increase of mechanical strength following much loss in porosity. The carbonized aggregate manufactured at $900^{\circ}C$ adding 30 % clay in sewage sludge was higher a little in porosity and 3 times in mechanical strength than those at $700^{\circ}C$ not adding clay. Consequently, in manufacturing the carbonized aggregate having simultaneously high porosity and mechanical strength, it is desirable to have operational condition of $900{\sim}1000^{\circ}C$ temperature and 1 hour time, and clay addition within 30 % for further higher mechanical strength.