• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.123-123
• /
• 2008

In this work, amorphous carbon thin films were deposited for hard mask applications by a reactive particle beam (RPB) assisted sputtering system at room temperature. The depositing characteristics of the films were investigated as functions of operating parameters such as reflector bias voltage and RF plasma power. It was confirmed that the deposition rate increased with increasing the reflector bias voltage and RF plasma power. By an atomic force microscope (AFM), it was revealed that the surface roughness was also increased. The total stress in films was determined by the use of the substrate curvature and its result will be discussed.

• 한국안전학회지
• /
• 제11권1호
• /
• pp.84-89
• /
• 1996

The adsorption characteristics of active carbon used as a cartridge filler of organic vapor respirator were examined by humidity, particle size, challenge concentration and specific surface area. As a result, the 1% breakthrough time of Carbon Tetrachloride($CCl_4$) was decreased with increase of relative humidity, challenge concentration and particle size (0.6～2.0mm) of active carbon. The adsorbed amount of $CCl_4$ was about 1. 1mg/$m^2$ at RH 40% and 0. 5mg/$m^2$ at RH 80% . However in the case of prehumidified active carbon, humidity did not affected to 1% breakthrough time up to RH 40%.

• Carbon letters
• /
• 제14권2호
• /
• pp.121-125
• /
• 2013

In this study, PtRu nanoparticles deposited on binary carbon supports were developed for use in direct methanol fuel cells using carbon blacks (CBs) and multi-walled carbon nanotubes (MWCNTs). The particle sizes and morphological structures of the catalysts were analyzed using X-ray diffraction and transmission electron microscopy, and the PtRu loading content was determined using an inductively coupled plasma-mass spectrometer. The electrocatalytic characteristics for methanol oxidation were evaluated by means of cyclic voltammetry with 1 M $CH_3OH$ in a 0.5 M $H_2SO_4$ solution as the electrolyte. The PtRu particle sizes and the loading level were found to be dependent on the mixing ratio of the two carbon materials. The electroactivity of the catalysts increased with an increasing MWCNT content, reaching a maximum at 30% MWCNTs, and subsequently decreased. This was attributed to the introduction of MWCNTs as a secondary support, which provided a highly accessible surface area and caused morphological changes in the carbon supports. Consequently, the PtRu nanoparticles deposited on the binary support exhibited better performance than those deposited on the single support, and the best performance was obtained when the mass ratio of CBs to MWCNTs was 70:30.

• Journal of Mechanical Science and Technology
• /
• 제15권6호
• /
• pp.804-812
• /
• 2001

A triboelectrostatic separation system for removing unburned carbon from coal fly ash is designed and evaluated. Fly ash from a coal-fired power plant is used as an accepted additive in concrete where it adds strength, sulfate resistance and reduced cost, provided acceptable levels of unburned carbon are maintained. Unfortunately, unburned carbon in coal fly ash absorbs some of other additives and reduces the concrete strength. This paper describes to investigate dry triboelectrostatic process to separate unburned carbon from coal fly ash and utilize it into economically valuable products. The laboratory-scale triboelectrostatic separation system consists of a particle feeding system, a tribocharger, a separation chamber, and collection systems. Particles of unburned carbon and fly ash can be imparted positive and negative surface charges, respectively, with a copper tribocharger due to differences in the work function values of the particles and the tribocharger, and can be separated by passing them through an external electric field. Results showed that fly ash recovery was strongly dependent on the electric field strength and the particle size. 70wt% of fly ash containing 6.5wt% of carbon contents could be recovered at carbon contents below 3%. The triboelectrostatic separation system showed a potential to be an effective method for removing unburned carbon from coal fly ash.

• 한국재료학회지
• /
• 제20권2호
• /
• pp.104-110
• /
• 2010

The characteristics of all polymer composites containing carbon materials are determined by four factors: component properties, composition, structure and interfacial interactions. The most important filler characteristics are particle size, size distribution, specific surface area and particle shape. As a consequence, in this paper we discuss the aspects of the mechanical, electrical and thermal properties of composites with different fillers of carbon black, carbon nanotube (CNT), graphene and graphite and focus on the relationship between factors and properties, as mentioned above. Accordingly, we fabricate rubber composites that contain various carbon materials in carbon black-based and silica based-SBR matrixes with dual phase fillers and use scanning electron microscopy, Raman spectroscopy, a rhometer, an Instron tensile machine, and a thermal conductivity analyzer to evaluate composites' mechanical, fatigue, thermal, and electronic properties. In mechanical properties, hardness and 300%-modulus of graphene-composite are sharply increased in all cases due to the larger specific surface. Also, it has been found that the thermal conductivity of the CNT-composite is higher than that of any of the other composites and that the composite with graphene has the best electrical properties.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.459-462
• /
• 2008

슬러리 연료 제조 시 카본의 분산안정성에 미치는 공정변수의 영향을 조사하였다. 슬러리연료 저장용기의 세군데(위, 중간, 아래) 위치별로 채취된 시료에서 평균입도와 탄소함량을 분석하여 Jet A-1에서 카본의 분산안정성을 측정하였다. 여러 종류의 첨가제를 적용한 결과, NB463S84 사용 시 분산성과 증가된 중력 가속도하에서 안정성이 가장 우수하였다. 동일 조건에서 카본층 높이 변화와 카본의 평균입도 측정을 통하여 혼합장비의 성능을 비교하였고, 실험실 규모에서 얻은 제조조건을 bench 규모 제조에 적용하여 본 연구의 실용 가능성을 확인하였다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제23권6호
• /
• pp.104-113
• /
• 2018

A three-dimensional electrochemical process using nanosized zero-valent iron (NZVI)/activated carbon (AC) particle electrode and persulfate (PS) was developed for oxidizing pollutants. X-ray diffraction (XRD), scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS), and Brunauer-Emmett-Teller (BET) surface area analysis were performed to characterize particle electrode. XRD and SEM-EDS analysis confirmed that NZVI was impregnated on the surface of AC. Compared with the conventional two-dimensional electrochemical process, the three-dimensional particle electrode process achieved three times higher efficiency in phenol removal. The system with current density of $5mA/cm^2$ exhibited the highest phenol removal efficiency among the systems employing 1, 5, and $10mA/cm^2$. The removal efficiency of phenol increased as the Fe contents in the particle electrode increased. The particle electrode achieved more than 70% of phenol removal until it was reused for three times. The sulfate radical played a predominant role in phenol removal according to the radical scavenging test.

• Ocean and Polar Research
• /
• 제44권3호
• /
• pp.221-233
• /
• 2022

A sediment trap had been deployed at 1250 m depth in the Eastern Tropical Pacific (ETP) from September 2009 to July 2010, with the aim of understanding the temporal and vertical variability of particle flux. During the monitoring period, total particle flux varied from 12.4 to 101.0 mg m^-2day^-1, with the higher fluxes in January-March 2010. Biogenic particle flux varied in phase with the total particle flux. The increase in total particle flux during January-March 2010 was attributed to the enhanced biological production in the surface layer caused by wind-driven mixing in response to the seasonal shifts in the location of the Intertropical convergence zone. The export ratio (e-ratio) was estimated using the particulate organic carbon flux and satellite-derived net primary production data. The estimated e-ratios changed between 0.8% and 2.8% (1.4±0.6% on average). The ratio recorded in the negative phase of Pacific decadal oscillation (PDO) was similar to the previous results obtained from the ETP during the 1992/93 periods in the positive phase of PDO. This suggests that the regime shift of the PDO is not related to the carbon export ratio.

• 청정기술
• /
• 제24권3호
• /
• pp.157-165
• /
• 2018

본 연구에서는 초임계 이산화탄소와 공용매 첨가물을 이용하여 실리콘 웨이퍼 표면의 $Si_3N_4$ 파티클을 제거하는 기술을 조사하였다. 우선, 몇 가지 계면활성제와 첨가제에 관한 초임계 이산화탄소 용해도 및 파티클 분산성 평가를 통하여 초임계 공정에 대한 적합성을 확인하였다. 다양한 변수를 조정하여 파티클 세정 실험을 진행하여 최적의 제거 조건을 확립하였다. 실험에 사용된 계면활성제는 파티클 제거 효과가 떨어졌으며, 실험 후 이차 오염물이 형성됨을 확인하였다. 반면 trimethyl phosphate는 IPA공용매와 미량의 HF와 혼합된 세정 첨가제로서 초임계 이산화탄소에 5 wt%로 포함한 유체로 온도 $50^{\circ}C$, 압력 2000 psi에서 $15mL\;min^{-1}$의 유속으로 4분 간 세정한 결과, 85%의 파티클 제거 효율을 나타내었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.310-313
• /
• 2005

The conical fluidizing system of a binary mixture of Geldart C powders and Geldart A particles was defined as the conical powder-particle fluidized bed. We used a cold conical powder-particle fluidized bed model having a 0.104m-I.D. and 0.6m-high with an apex angle of $10^{\circ}$ for fluidization of a binary powder-particle mixture of 50 $vol\%$ fine carbon black powders (HI-900L, Korea Carbon Black Co.) and coarse alumina particles $(90{\mu}m)$ under different superficial gas velocities (0-0.1 m/s). The differential bed pressure drop increases with increasing gas velocity, and it goes from zero to a maximum value with increasing or decreasing gas velocity. In the conical fluidized beds of fine powders, demarcation velocities of the partial fluidization, full fluidization, partial defluidization was not observed.