• 한국응용과학기술학회지
• /
• 제23권3호
• /
• pp.199-206
• /
• 2006

Direct decomposition of methane over three types of carbon black (N330-p, N330-f, and HI-900L) was carried out in a fluidized bed quartz reactor. Properties of carbon black before and after reaction were measured and found to be related with surface structure and weight gain. For N330-p and N330-f, some carbon deposit on the surface was considered to be the reason for the increase of BET surface area and pore volume with weight gain. Carbon deposits on the surface and the conglutination of some aggregates may explain the slight increase of particle size. Properties of HI-900L changed much more significantly with weight gain. It is supposed that the increase of aggregate size of HI-900L were due to some unknown oily components. The corresponding agglomeration might be the reason for the decrease of BET surface area with weight gain, as compared with the increase of that for the case of N330 black.

• 한국대기환경학회지
• /
• 제13권3호
• /
• pp.179-191
• /
• 1997

The concentrations of organic and elemental carbon were determined using fine particle samples collected from Kosan, Cheju Island during the summer seasons of 1994 and 1995. The daily mean concentrations of organic and elemental carbon for each measurement period were 3.74 and 0.27 $\mu\textrm{g}$/㎥ in 1994, while those of 1995 were 2.36 and 0.10 $\mu\textrm{g}$/㎥, respectively The concentrations of organic carbon were higher than those commonly observed from clean areas around the world, but those of elemental carbon were lower than, or comparable to, other clean areas in the world. The resulting ratios of total carbon to elemental carbon at this site were thus higher than those seen from other metropolitan and non-polluted regions abroad. In addition according to our analysis, the 1994 measurement period can be classified into two periods: enhanced (July 20 and August 1) and reduced levels (August 2 and 9) of the carbonaceous species. The observed difference between two periods may be in part accounted for by the air trajectories representing each period. During the former period, the air masses from the Asian continent and Japan were dominant, while the air masses from the North Pacific Ocean came during the latter period. OC/EC ratios at the site were calculated to predict the possible formation of secondary organic aerosol . Based on our observations, we suggest that the formation of secondary organic aerosol might be an important pathway to the production of organic carbons.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 추계학술대회 논문집
• /
• pp.411-414
• /
• 2009

Photo-capacitor electrodes are attracting great attention because of their high capacitance and potential applications in electronic devices. Carbon capacitor, active carbon capacitor and its combination will be fabricated using simple sandwich capacitor electrode method as carbonaceous material on each type of capacitor electrodes with 20 ${\times}$ 15 mm cell size. Carbon/active carbon cell was fabricated using sol-gel process with 120oC dry temperature in l hour and using sintering process with 500oC in 2 hour. The effect of sintering temperature on carbon properties was also investigated with X-ray diffraction technique to get the best sintering temperature. The detail of fabrication process will be explained. Elemental composition in electrode material can be measured using quantitative spectroscopic as and a cyclic voltammetric technique was used to study the combined effects of electrode material and effect of annealing temperature and also time on the capacitance of thermally treated in capacitor electrode. In this work, characterization impedance technique is used to measurement of capacitance and giving complementary results. Active carbon as carbonaceous material has a better capacitance in charge/discharge process with mean thickness $32{\mu}m$ and with particle size $1{\mu}m$ to $4.5{\mu}m$ in 20 ${\times}$ 15 mm sample size of capacitor electrode.

• 한국분말재료학회지
• /
• 제20권4호
• /
• pp.291-296
• /
• 2013

SKD11 (ASTM D2) tool steel is a versatile high-carbon, high-chromium, air-hardening tool steel that is characterized by a relatively high attainable hardness and numerous, large, chromium rich alloy carbide in the microstructure. SKD11 tool steel provides an effective combination of wear resistance and toughness, tool performance, price, and a wide variety of product forms. The CNTs was good additives to improve the mechanical properties of metal. In this study, 1, 3 vol% CNTs was dispersed in SKD11 matrix by mechanical alloying. The SKD11+ CNT hybrid nanocomposites were investigated by FE-SEM, particle size distribution, hardness and wear resistance. The CNT was well dispersed in the SKD11 matrix and the mechanical properties of the composite were improved by CNTs addition. It shows good feasibility as cold work die tool.

• 한국재료학회지
• /
• 제21권4호
• /
• pp.196-201
• /
• 2011

It is known that the relative dielectric constant of insulating polyethylene matrix composites with conducting materials (such as carbon black and metal powder) increases as the conducting material content increases below the percolation threshold. Below the percolation threshold, dielectric properties show an ohmic behavior and their value is almost the same as that of the matrix. The change is very small, but its origin is not clear. In this paper, the dielectric properties of carbon black-filled polyethylene matrix composites are studied based on the effect medium approximation theory. Although there is a significant amount of literature on the calculation based on the theory of changing the parameters, an overall discussion taking into account the theory is required in order to explain the dielectric properties of the composites. Changes of dielectric properties and the temperature dependence of dielectric properties of the composites made of carbon particle and polyethylene below the percolation threshold for the volume fraction of carbon black have been discussed based on the theory. Above the percolation threshold, the composites are satisfied with the universal law of conductivity, whereas below the percolation threshold, they give the critical exponent of s = 1 for dielectric constant. The rate at which the percentages of both the dielectric constant and the dielectric loss factor for temperature increases with more volume fraction below the percolation threshold.

• 한국재료학회지
• /
• 제17권11호
• /
• pp.601-605
• /
• 2007

The tribological properties of acrylonitrile-butadiene rubber (NBR) filled with two kinds of carbon black filler were examined. Different types of Semi-Reinforcing Furnace (SRF), and High Abrasion Furnace (HAF) blacks were used as filler material to test the influence of carbon black particle size on the friction and wear of NBR. Results from tribological tests using a ball on disk method showed that the smaller HAF particles were more effective for reducing the wear of NBR during frictional sliding. The hardness, elastic modulus at 100% elongation, and elongation at break were measured to examine the correlation between the effects of carbon black on the mechanical and tribological properties of the NBR specimens. The wear tracks of the NBR specimens were observed with scanning electron microscopy (SEM). The wear tracks for NBR with different ratios of SRF and HAF showed clearly different abrasion patterns. Mechanisms for the friction and wear behavior of NBR with different sizes of carbon black filler were proposed using evidence from wear track observation, as well as the mechanical and tribological test results.

• 한국표면공학회지
• /
• 제41권3호
• /
• pp.114-120
• /
• 2008

The pyrolysized carbon xerogel and aerogels were prepared from the sol-gel polymerization of resorcinol-formaldehyde(RF) followed by the dry process under ambient pressure and supercritical carbon dioxide condition respectively. The thermal behaviour of RF polymer xerogel was investigated with TGA analyzer to correspond with the pyrolysis process. The surface properties such as particle size, morphology and the point of zero charge of the pyrolysized porous carbon aerogels were studied for the precious metal catalyst supported media. It was found that the volume of the polymer aerogel decreased because of the significant linear shrinkage and weight loss of polymer gel during the carbonization. The point of zero charge of the carbon aerogel pyrolysized at $1050^{\circ}C$ under inert gas flow was about 10.

• 한국태양에너지학회 논문집
• /
• 제33권3호
• /
• pp.99-106
• /
• 2013

Recently, high-thermal-conductivity graphene and carbon nanotube nanoparticles have attracted particularly close attention from researchers. In the present study, the thermal conductivity and viscosity properties of two kinds of graphene and carbon nanotube nanofluids added to distilled water - two graphenes and carbon nanotubes of differing size - were compared and analyzed. The thermal conductivities of the nanofluids, formulated in the usual manner by adding graphene and carbon nanotube to distilled water and subjecting the mixture to ultrasonic dispersion, were measured by the transient hot-wire method, and the viscosities were determined using a rotational digital viscometer. As a result, we concluded that the nanofluid of small particle diameter of graphene have outstanding properties as heat transfer media, due to their excellent thermal conductivity and viscosity, compared with the other nanofluid.

• 자원리싸이클링
• /
• 제9권6호
• /
• pp.36-44
• /
• 2000

석탄회는 기포에 잘 부착되는 미연탄소 성분의 입자와 기포에 부착되지 않는 산화광물 성분의 입자로 구성되어 있으므로, 석탄회입자를 수중에 부유시킨 상태에서 기포를 발생시키면 미연탄소와 산화광물질 입자를 각각 분리할 수 있다. 분리된 이들 두 종류의 입자들은 건축용 재료, 화장품, 섬유 및 반도체의 충진제(Filler), 흡착제, 야금용 탄소 등과 같이 고부가가치 원료로 활용이 가능하다. 본 연구는 부유선별법에 의해 구성된 향류컬럼부유분리장치를 이용하여 혼합입자인 석탄회 입자를 효율적으로 분리하고자 하는 것인데, 분리특성은 기포와 혼합입자의 특성에 따라 결정된다. 기포의 특성에 대한 연구는 장치의 설계와 밀접한 관련이 있기 때문에 선행연구에서 충분히 이루어졌으나 혼합입자의 특성에 따른 분리효율 평가에 관한 연구는 수행되지 않고 있다. 혼합입자인 석탄회가 분리에 미치는 특성을 파악하기 위해 석탄회 입자의 질량중앙직경이 23, 95, 190$mu extrm{m}$일 때, 미연탄소의 함량이 7, 11, 20%일 때에 각각의 분리효율을 분석하였다. 그 결과 공급되는 석탄회 입자의 크기가 작을수록,미연탄소 함량이 작을수록 분리효율이 증가하였다. 즉 포수제 투입량이 8$\ell$/ton-fa로 같은 조건에서 미연탄소 함량이 7%와 20%인 경우 분리효율은 각각 86%와 74%로 분석되었으며 질량중앙직경이 23$mu extrm{m}$와 190$\mu\textrm{m}$ 일 때 분리효율은 각각 74%와 39%로 분석되었다. 결국 석탄회에서 소수성인 미연탄소의 함유량이 증가할수록 분리효율은 감소하는 반면 입자의 크기가 작을수록 기포와의 부착성능이 향상되어 분리효율은 향상되는 것으로 분석되었다.ta$/$\beta$/$\gamma$/$\alpha$/$\alpha$/$\beta$]r 배향각을 갖는 적층판을, 일반기술자들이 이해하기 쉬운 본 논문의 방법으로 해석하는 방법을 제시하고 기술자들의 참고자료로 사용될 수 있는 여러 가지 경우에 대한 고유진동수의 계산결과가 제공되고 있다. 고유진동수의 계산결과가 제공되고 있다. 사료된다.거나 둔화되는 것으로 분석된다.으로 분석된다..리학적 부하량이 2 $m^3$/$m^2$/min 일때, 2 kg 02 kg $O_2$/kW-hr의 가장 높은 표준에어레이션효율을 나타내었다. 위의 두 실험 결과에 따라 packed column 에어레이터에서 발포스티로폼 입자를 산소전달 매질로 이용하여 산소 전달률을 증가시킬 수 있다는 것을 확인할 수 있었다.i, Cu, Y, Nb, La, Nd, Pb, Th in excess of 10 ppm. Relatively high amount of most trace elements were detected in the Hwangto. The major and minor chemical compositions of the Hwangto were different depending on the types of host rocks. However, their difference was in the similar range compared with the compositions of host rocks. electron acceptor triggers sensory transduction processes in B. japonicum.t

• 한국자동차공학회논문집
• /
• 제17권5호
• /
• pp.67-73
• /
• 2009

Recently, Europe decided to start the regulation of diesel engine nanoparticles because of its well known adverse health effects. The diesel nanoparticles can be classified as solid carbon particles and volatile particles. The volatile particles generates during dilution process by condensation of gas phase volatile compounds such as hydrocarbon. The new nanoparticle regulation considers only solid particles because of difficulty of measurement of volatile particles. The aim of this study is to suggest a proper dilution method that prevent the volatile particle generation. As a result, it is found that the $1^{st}$ dilution air temperature should be above $120^{\circ}C$ in order to prevent volatile particle generation effectively. It is also found that the volatile particles can be removed effectively in the evaporation tube by the increase of evaporation tube temperature. But when exhaust gas is hot enough (>$190^{\circ}C$, in this study) and it is diluted in the first diluter with high temperature air (>$120^{\circ}C$), removal phenomenon of volatile particles by increasing of evaporation tube temperature can not be seen. It means that there are no volatile particles in the diluted exhaust gas. Additionally, dilution ratio is not an important factor for volatile particle generation compared with dilution air temperature or evaporation tube temperature.