• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.171-178
• /
• 2008

The combustion and exhaust emission characteristics were investigated in an DME fueled HCCI engine. Carbon dioxide, nitrogen and mixed gas, which was composed of carbon dioxide and nitrogen, were used as control parameters of combustion and exhaust emission. As the oxygen concentration in induction air, which was occurred by carbon dioxide, nitrogen and mixed gas, was reduced, the start of auto-ignition was retarded and the burn duration was extended due to obstruction of combustion and reduction of combustion temperature. Due to these fact, indicated mean effective pressure was increased and indicated combustion efficiency was decreased by carbon dioxide, nitrogen and mixed gas. In case of exhaust emission, hydrocarbon and carbon monoxide was increased by reduction of oxygen concentration in induction air. Especially, partial burning was appeared at lower than about 18% of oxygen concentration by supplying carbon dioxide. However it was overcome by intake air heating.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.58-64
• /
• 2007

As the concerns regarding global worming were increased, the pressure of greenhouse gas(GHG) emission reduction on mobile source was also increased. Carbon dioxides contribute over 90% of total GHG emission and the mobile source occupies about 20% of this $CO_2$ emission. Therefore automotive exhaust is suspected to be one of the major reasons of the rapid increase in greenhouse effect gases in ambient air. In this study, in order to investigate $CO_2$ emission characteristics from gasoline passenger cars(PC), which is the most dominant vehicle type in Korea, 106 vehicles were tested on the chassis dynamometer. $CO_2$ emissions and fuel efficiency were measured. The emission characteristics by displacement, gross vehicle weight, vehicle speed and CVS-75/vehicle speed mode were discussed. Test modes were vehicle speed modes and CVS-75 mode that have been used to develop emission factors and to regulate for light-duty vehicle in Korea. It was found that $CO_2$ emissions showed higher large displacement, heavy gross vehicle weight, low vehicle speed and CVS-75 mode than small displacement, light gross vehicle weight, high vehicle speed and vehicle speed mode, respectively. From these results, correlation between $CO_2$ emission and fuel efficiency was also determined. The results of this study will contribute to domestic greenhouse gas emissions calculation and making the national policy for climate change.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.85-93
• /
• 2001

Minimized canister flow restriction and maximized flow uniformity are desired to maximize a purge capability. With the impending ORVR(On Board Refueling Vapor Recovery) systems, the reduction of restriction and increase of flow uniformity in a carbon canister becomes even more critical to meet the stringent regulation. In this study, three-dimensional numerical simulations have been performed to investigate the three-dimensional internal flow patterns in a carbon canister during purge. The effects of the declined angle of the purge pipe and the number of partitions on the pressure drop and purge efficiency in a carbon packed bed are examined. Results show that the purge efficiency and space velocity distribution are affected in the upstream region of 40% of total canister bed by porosity of carbon granule and angle of purge pipe. It is also found that the purge efficiency decreases with increasing the number of partitions.

• Journal of the Korea Safety Management & Science
• /
• v.16 no.2
• /
• pp.231-236
• /
• 2014

In this study, the changes in collection efficiencies due to the time changes of activated carbons were ascertained, and in order to identify the magnitude of adsorption, the before-use and after-use iodine adsorption values were analyzed. In addition, as a result of examining the characteristics of continuous process and non-continuous process and as a result of investigating whether the emission standards would be maintained, the continuous process and printing facilities were seen as not being able to maintain the emission standards. Also were found, in the case of non-continuous process,-taking into consideration the special nature of the job -for 4${\o}$ palletized charcoal, a collection efficiency near 50% was shown even after 96 hours. Also, when the inlet concentration was about 300ppm, it is thought that the emission standards would be maintained if the activated carbons are replaced within at least 96 hours in the case of 4${\o}$ palletized charcoal and the use was deemed pointless in the case of carbon. The results of this study are expected to provide assistance in selecting replacement periods for activated carbons and in selecting absorbents at the project sites, and are expected to be of significant help in the selection of precipitators that can collect total hydrocarbons for compliance of the emission standards.

• Korean Journal of Materials Research
• /
• v.17 no.3
• /
• pp.173-178
• /
• 2007

Carbon nanotube cathodes(CNT cathodes) with a trench structure similar to gated structure of triode-type cathode were fabricated by a screen printing method using multi-walled carbon nanotubes. The effects of surface treatments on CNT cathodes were investigated for high efficiency field emission displays(FEDs). A liquid method easily removed the organic residue and protruded the CNTs. Field emission properties were measured by using a diode-type mode. The liquid method produced a turn-on field of $1.4V/{\mu}m$. The emission current density was measured about $3.1mA/cm^{2}$ at the electric field of $3V/{\mu}m$. The liquid method showed a high potential applicable to the surface treatment for triode-type FEDs.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.10-15
• /
• 2009

Emission regulations on greenhouse gas(GHG) in automobiles have been stringent because of global warming effect. Over 90% of total GHG emission are carbon dioxides and about 20% of this $CO_2$ emission are emitted from automobiles. In this study, 110 vehicles were tested on a chassis dynamometer and $CO_2$ emissions and fuel economy were measured in order to investigate the characteristics of $CO_2$ emission factor from passenger vehicles which are the most dominant vehicle type in Korea. The characteristics of emissions in accordance with displacements, gross vehicle weight, NIER and CVS-75 speed mode were discussed. It was found that vehicles having larger displacement, heavier gross vehicle weight, automatic transmission and specially at cold start emitted more $CO_2$ emissions. From these results, correlation between $CO_2$ emission and fuel economy was also obtained. This study may contribute to evaluate domestic greenhouse gas emissions and establish national policies on climate changes in future.

• Journal of Korea Trade
• /
• v.26 no.1
• /
• pp.113-125
• /
• 2022

Purpose - The primary purpose of this study is to verify whether the target set out by the International Maritime Organization (IMO) for reducing carbon emissions from ships can be achieved by quantitatively analyzing the trends in technological advances of fuel oil consumption in the container shipping market. To achieve this purpose, several scenarios are designed considering various options such as eco-friendly fuels, low-speed operation, and the growth in ship size. Design/methodology - The vessel size and speed used in prior studies are utilized to estimate the fuel oil consumption of container ships and the pace of technological progress and Energy Efficiency Design Index (EEDI) regulations are added. A database of 5,260 container ships, as of 2019, is used for multiple linear regression and quantile regression analyses. Findings - The fuel oil consumption of vessels is predominantly affected by their speed, followed by their size, and the annual technological progress is estimated to be 0.57%. As the quantile increases, the influence of ship size and pace of technological progress increases, while the influence of speed and coefficient of EEDI variables decreases. Originality/value - The conservative estimation of carbon emission drawn by a quantitative analysis of the technological progress concerning the fuel efficiency of container vessels shows that it is not possible to achieve IMO targets. Therefore, innovative efforts beyond the current scope of technological progress are required.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.46
• /
• pp.265-313
• /
• 2010

Kyoto Protocol is an international convention on concrete performance program for UNFCCC(United Nations Framework Convention on Climate Change), which regulate and prevent to global warming and officially came into effect on February 16, 2005. Kyoto flexible mechanisms, the agreed environmental system in March 1997 in the Third Conference of Parties in UNFCCC General Assembly, Emission Trading System(ETS), Clean Development Mechanism(CDM) and Joint Implementation(JI), are key policies related to environment. In advanced countries, greenhouse gas emissions should be reduced average 5.2% level compared to 1990 in total emissions during 2008-2012. World leading carbon market finished the trial on the EU ETS I greenhouse gas emissions trading system, EU ETS II is operated regularly after 2008. World Bank leads to make 'Prototype Carbon Fund(PCF)' in April 2004, which is the world first carbon fund and a representative public carbon fund type, World Bank operate various funds including present PCF. Thus, I would like to propose as follows in relation to this study: First, in the validity analysis of carbon funds, it would be needed to analyze the Emission Reduction Cost Efficiency(ERCE) of carbon. The ERCE is a break-even value which brings the Net Present Value(NPV) to zero. NPV approach is used among projects and it enables potential projects to be compared and evaluated the ERCE on the basis of the net present value of net future cash flows. Therefore, according to results of analysis, carbon funds should be developed and invested. Second, it would be necessary to allow of issuing bonds together with carbon funds, carbon finance etc. Third, carbon funds, it would be reasonable to have a relatively enough maturity in project and as a financial derivatives in the international financial markets, it is needed various types of transactions. Fourth, it would be needed to standardize the carbon emissions trading for more efficiently. Fifth, it would be necessary to establish and invest in various kinds of domestic and overseas global carbon funds, including governments, privates, governments and privates sectors. And it is also needed to establish the medium and long term plans for carbon funds. Sixth, it would be needed to foster the advanced trade mechanisms for carbon funds in the most effective ways. Finally, carbon funds should be used in harmony with international societies to reduce global warming as the social responsible investing funds and it should be contribute to sustainable development. In addition, it would seem that carbon funds should be studied on establishing the contributable standard of sustainable development in the future assignment.

• Korean Journal of Soil Science and Fertilizer
• /
• v.47 no.6
• /
• pp.457-463
• /
• 2014

This study was carried out to find out major factors to mitigate carbon emission using Life Cycle Assessment (LCA). System boundary of LCA was confined from sowing to packaging during vegetable production. Input amount of agri-materials was calculated on 2007 Income reference of white radish, chinese cabbage and chive produced at open field and film house published by Rural Development Administration. Domestic data and Ecoinvent data were used for emission factors of each agri-material based on the 1996 IPCC guideline. Carbon footprint of white radish was 0.19 kg $CO_2kg^{-1}$ at open fields, 0.133 kg $CO_2kg^{-1}$ at film house, that of chinese cabbage was 0.22 kg $CO_2kg^{-1}$ at open fields, 0.19 kg $CO_2kg^{-1}$ at film house, and that of chive was 0.66 kg $CO_2kg^{-1}$ at open fields and 1.04 kg $CO_2kg^{-1}$ at film house. The high carbon footprint of chive was related to lower vegetable production and higher fuel usage as compared to white radish and Chinese cabbage. The mean proportion of carbon emission was 35.7% during the manufacturing byproduct fertilizer; white radish at open fields was 50.6%, white radish at film house 13.1%, Chinese cabbage at outdoor 38.4%, Chinese cabbage at film house 34.0%, chive at outdoor 50.6%, and chive at film house 36.0%. Carbon emission, on average, for the step of manufacturing and combustion accounted for 16.1% of the total emission; white radish at open fields was 4.3%, white radish at film house 15.6%, Chinese cabbage at open fields 6.9%, Chinese cabbage at film house 19.0%, chive at open fields 12.5%, and chive at film house 29.1%. On the while, mean proportion of carbon footprint for the step of $N_2O$ emission was 29.2%; white radish at open fields was 39.2%, white radish at film house 41.9%, Chinese cabbage at open fields 34.4%, Chinese cabbage at film house 23.1%, chive at open fields 28.8%, and chive at film house 17.1%. Fertilizer was the primary factor and fuel was the secondary factor for carbon emission among the vegetables of this study. It was suggested to use Heug-To-Ram web-service system, http://soil.rda.go.kr, for the scientific fertilization based on soil testing, and for increase of energy efficiency to produce low carbon vegetable.

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.4
• /
• pp.451-458
• /
• 2006

Automotive exhaust is suspected to be one of the major reasons of the rapid increase in greenhouse effect gases in ambient air. As the concerns regarding global worming were increased, the pressure on mobile source greenhouse gas (GHG) emission were also increased. Carbon Dioxides contribute over 90% of total GHG emission and the mobile source occupies about 20% of this $CO_2$ emission. In this study, in order to investigate $CO_2$ emission characteristics from gasoline and LPG passenger cars (PC), which is the most dominant vehicle type in Korea, 53 vehicles were tested on the chassis dynamometer. $CO_2$ emissions and fuel consumption efficiency were measured. The emission characteristics by fuel type, model year, mileage, vehicle speed and transmission type were also discussed. Test modes used in this study were NIER 10 modes and CVS-75 mode, which have been used for developing emission factors and testing new vehicles respectively. The results of this study showed that the main factors which have significant influences on the $CO_2$ emissions are fuel type, transmission type, displacement of vehicle and mileage. The correlation between $CO_2$ emission and FE was also determined by comparing $CO_2$ emission and fuel consumption efficiency. The overall results of this study will greatly contribute to domestic greenhouse gas emissions calculation and designing national strategies for climate change.