• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.476-482
• /
• 1997

A portable electronic nose system has been fabricated and characterized using an oxide semiconductor gas sensor array and pattern recognition techniques such as principal component analysis and back-propagation artificial neural network. The sensor array consists of six thick-film gas sensors whose sensing layers are Pd-doped $WO_{3}$, Pt-doped $SnO_{2}$, $TiO_{2}-Sb_{2}O_{5}-Pd$-doped $SnO_{2}$, $TiO_{2}-Sb_{2}O_{5}-Pd$-doped $SnO_{2}$ + Pd coated layer, $Al_{2}O_{3}$-doped ZnO and $PdCl_{2}$-doped $SnO_{2}$. The portable electronic nose system consists of an 16bit Intel 80c196kc as CPU, an EPROM for storing system main program, an EEPROM for containing optimized connection weights of artificial neural network, an LCD for displaying gas concentrations. As an application the system has been used to identify 26 carbon monoxide/hydrocarbon (CO/HC) car exhausting gases in the concentration range of CO 0%/HC 0 ppm to CO 7.6%/HC 400 ppm and the identification has been successfully demonstrated.

• Korean Chemical Engineering Research
• /
• v.55 no.1
• /
• pp.107-114
• /
• 2017

The performance of polymer electrolyte membrane fuel cell (PEMFC) could be deteriorated when fuel contains contaminants such as carbon monoxide (CO) or hydrogen sulfide ($H_2S$). Generally, $H_2S$ is introduced in hydrogen by steam reforming of hydrocarbon which has mercaptan as odorant. $H_2S$ poisoning effect on PEMFC performance was examined on this study. Pure hydrogen injection, voltage cycling and water circulation methods were compared as performance recovery methods. The PEMFC performance was analyzed using electrochemical methods such as polarization curve, electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). Pure hydrogen injection and voltage cycling methods showed low recovery ratio, however, water circulation method showed high recovery ratio over 95%. Because anode was directly poisoned by $H_2S$, anode water circulation showed higher recovery ratio compared to the other methods. Water circulation method was developed to recover PEMFC performance from $H_2S$ poisoning. This method could contribute to PEMFC durability and commercialization.

• Korean Chemical Engineering Research
• /
• v.55 no.1
• /
• pp.121-129
• /
• 2017

Pd based catalysts were prepared by impregnating palladium precursor using incipient wetness method on $TiO_2$, $Al_2O_3$, $ZrO_2$, and $SiO_2$ and were applied for the selective oxidation of $H_2$ in the presence of CO. Their physicochemical properties were studied by X-ray diffraction (XRD), $N_2$-sorption, temperature programmed desorption of CO (CO-TPD) and (CO+$H_2O$)-TPD, temperature programmed reduction of CO (CO-TPR) and XPS a. The results of CO- and (CO+$H_2O$)-TPD showed the correlation between peak temperature of TPD and catalytic activities for $H_2$ and CO conversion. The $Pd/ZrO_2$ catalyst exhibited the highest conversion of $H_2$. The addition of $H_2O$ vapor promotes the conversion of $H_2$ and CO by inducing easy desorption of CO and $H_2$ in the competitive adsorption of $H_2O$, CO and $H_2$.

• Elastomers and Composites
• /
• v.38 no.4
• /
• pp.316-325
• /
• 2003

The blends of waste-polyethylene (W-PE)/waste-ethylene vinyl acetate copolymer (W-EVA) with inorganic and phosphorous flame retardants (i.e., aluminium hydroxide, magnesium hydroxide, and so on) were prepared by melt mixing techniques at different compositions and foamed. The flame retardancy and foaming properties of the blends, limiting oxygen index (LOI), heat release rate (HRR), carbon monoxide yield (COY), total heat release (THR), effective heat of combustion (EHC), expandability and cell structure were investigated using cone calorimeter, SEM, LOI tester and polarizing microscope. When the composition ratios of the W-PE/W-EVA blends were 50/50 (w/w), and the ranges of the flame retardants contents were $175{\sim}220 phr$, we could obtain foams with the uniform and closed cell, high expandability (1900 % or more), high LOI, and low HRR values. These results depend on crosslinking and loaming conditions, a char formation and smoke suppressing effect. Aluminium hydroxide had more effect in the increase of LOI than magnesium hydroxide, while magnesium hydroxide considerably affected the decrease of HRR and COY.

• Fire Science and Engineering
• /
• v.32 no.1
• /
• pp.7-15
• /
• 2018

The prediction performance of combustion models in the Fire Dynamics Simulator (FDS) were evaluated by comparing with experiment for compartment propane gas fires. The mixture fraction model in the FDS v5.5.3 and Eddy Dissipation Concept (EDC) model in the FDS v6.6.3 were adopted in the simulations. Four chemical reaction mechanisms, such as 1-step Mixing Controlled, 2-step Mixing Controlled, 3-step Mixing Controlled and 3-step Mixed (Mixing Controlled + finite chemical reactions) reactions, were implemented in the EDC model. The simulation results with each combustion model showed similar level for the temperature inside the compartment. The prediction performance of FDS with each combustion model showed significant differences for the CO concentration while no distinguished differences were identified for the $O_2$ and $CO_2$ concentrations. The EDC 3-step Mixing Controlled largely over-predicted the CO concentration obtained by experiment and the mixture fraction model under-predicted the experiment slightly. The EDC 3-step Mixed showed the best prediction performance for the CO concentration and the EDC 2-step Mixing Controlled also predicted the CO concentration reasonably. The EDC 1-step Mixing Controlled significantly under-predict the experimental CO concentration when the previously suggested CO yield was adopted. The FDS simulation with the EDC 1-step Mixing Controlled showed difficulties in predicting the $CO_2$ concentration when the CO yield was modified to predict the CO concentration reasonably.

• Journal of the Korean Chemical Society
• /
• v.19 no.3
• /
• pp.186-192
• /
• 1975

In the course of anthracite briquet combustion, air draft is usually controlled to continue burning of definite amount of briquet in the conventional hollow clay cylinder with air inlet hole open for given time, so that a large amount of CO tends to be produced. Therefore, it is necessary to establish an improved combustion process to depress the yielding rate of CO and for this purpose, we performed a basic experiment in which combustion rate of CO was measured in the mixture of $N_2, O_2 $and CO gas with or without the presence charcoal at the various temperature. The observed results showed that the burning temperature of CO is about 680${\sim}700^{\circ}C$, further burning rate of it was increased with increasing the amount of draft. From these facts, longer combustion time and low CO generation are thus contradictory to each other and it has been long desired to make those two compatible somehow. The purpose of the present investigation lies in designing an effective new briquet stove to meet the above requirements. The essential feature of the new briquet stove consisted in the use of two hollow iron cylinders with different inside diameter. A cylindrical air jacket thus formed served as a path through which small amount of secondary air run from the bottom of the stove to the upper vent holes. Heat exchange occurred between the upgoing secondary air and the burning briquet, which lowered the combustion temperature of the briquet. The results observed were selfevident as anticipated. It was confirmed that the combustion time was increased tolerably due to the heat loss from the combustion zone and that CO in the flue gas was reoxidized at the upper portion of the stove by the upgoing hot secondary air. By this reoxidation reaction the concentration of CO in the flue gas was found to be about 1/20 of that in case the conventional clay cylinder was used as briquet jacket.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.277-281
• /
• 2012

This work is concerned with a plan for preventing accidents of CO gas leak from gas boilers, involving the enforcement of installations of both CO alarm system and condensing boilers, and financial support of government grants. If amongst 1,460,000 beneficiaries of basic livelihood security, one million households in use of gas boilers receive 3-year support of 200,000 won, the difference of prices between common and condensing boilers, the government grants would be 2,000 billion won. If 3 million common householders are in 3-year support of 100,000 won, government grants would be 3,000 billion won. Therefore, 3-year grand total of government grants would be 5,000 billion won. Finance for government grants can be purveyed from energy saving; yearly 2,000 billion won of energy saving by enforcing to replace one million existing boilers with condensing boilers, leading to 2 trillion won of energy saving for 10 years. In this way, 6,000 billion won of 3-year grand total of government grants for CO alarm system and condensing boilers can be purveyed. The rest amount would be fundraised for energy savings. We claim that our proposal can make an achievement of more than 50% reduction of CO leak accidents during 10 years.

• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.417-420
• /
• 2012

This study is about reduction reaction making 2, 4-dinitrotoluene (2, 4-DNT) to 2, 4-toluene diisocyanate (2,4-TDI) with Pd/$SiO_2$. Catalytic systems based on Pd/$SiO_2$ at about $200^{\circ}C$ and under 100 bars of carbon monoxide. We studied the effect of pyridine on the yield of the TDI. TDI was not created without pyridine, but created with pyridine, at the reaction result. According to research, homogeneous synthesis of TDI with direct carbonylation, palladium and pyridine complexion is known to catalyze. When adding pyridine the reason of TDI synthesis is palladium leaching, ICP-AES was performed to confirm it. As a result, the proportion of Pd loaded in $SiO_2$ was decreased 52% than before, after the reaction by adding 20 vol% pyridine. Generating TDI by adding pyridine might be the effect of the complex ion, which is composed of leached palladium and pyridine.

• Journal of the Korean Chemical Society
• /
• v.40 no.2
• /
• pp.109-116
• /
• 1996

A matrix modification was studied for the determination of trace germanium in mineral waters by electrothermal atomic absorption spectrophotometry (ET-AAS). For this, the type and quantity of modifier as well as the use of auxiliary modifier were investigated to realize the efficient modification. Germanium suffers from low sensitivity and poor reproducibility in ET-AAS determination because of the premature loss of germanium via volatile germanium monoxide formation when heated in the presence of carbon. Therefore, the addition of a matrix modifier is necessary to stablize the germanium, thermally and chemically. By the addition of palladium (10 ${\mu}g/mL)$ as a single modifier to the sample containing 500 ng/mL germanium, the charring temperature could be raised from 800 to $1000^{\circ}C$, and its absorbance was also increased, but the atomization temperature was not raised. In this case, the absorbance of germanium was not changed in the range of 10∼70 ${\mu}g/mL$ of palladium added. On the other hand, it was considered that the use of a mixed modifier could modifiy the matrix more effectively than with a single modifier. The best results were obtained by using 1% ammonium hydroxide as an auxiliary modifier together with 10 ${\mu}g/mL$ palladium. The charring temperature could be raised from 800 to $1100^{\circ}C$, without any change of the atomization temperature. With above optimum conditions, the trace amount of germanium in several mineral waters were determined by a calibration curve method, and good recoveries of more than 95% were also obtained in the samples in which a given amount of germanium was spiked. The detection limit of this method was about 6.9 ng/mL.

• Journal of Haehwa Medicine
• /
• v.5 no.2
• /
• pp.497-497
• /
• 1997

간질성폐질변(間質性肺疾變)은 결체조직질병(結締組織疾病)의 상견(常見)되는 병발증(倂發證)이지만, 지금까지는 이상적(理想的)인 치료법(治療法)이 없었다. 본(本) 연구(硏究)는 본병(本病)의 병리기전(病理機轉)이 중의(中醫)에서의 "어혈(瘀血)"증(證) 상호(相互) 유사(類似)한 것으로부터 시작(始作)하여, 중의(中醫)의 "활혈화어법(活血化瘀法)"과 결합(結合)하여 치료(治療)하면서 환자(患者)의 폐기능(肺氣能) 검사결과(檢査結果)의 변화(變化)를 추적(追跡)해, 그 치료효과(治療效果)에 대(對)한 평가(評價)를 내리는 작업(作業)으로 이루어졌다. 먼저 풍습과(風濕科)에 의뢰(依賴)하여 결체조직질병(結締組織疾病)에 간질성폐병(間質性肺病)이 병발(倂發)한 환자(患者)를 선별(選別)한 후(後)에, 서의치료(西醫治療) 통(通)해서 그 원발성(原發性) 질병(疾病)이 은정(隱靜)한 상태(狀態)에까지 이르도록 한 후(後), 필요(必要)한 최저량(最低量)의 서의약(西醫藥)만을 유지(維持)케 하였다. 환자(患者)의 의사(意舍)에 따라서 두 개의 조(組)로 나누어, 실험군(實驗群)은 중의(中醫)에서 회진(會診)하고, Raynaud 증후군(症候群)의 유무(有無)에 따라서, 당귀사역탕(當歸四逆湯) 혹(或)은 혈부축어탕(血府逐瘀湯)을 농축분제(濃縮粉劑)로 투여(投與)하며 연속(連續)하여 6개월간(個月間) 치료(治療)하였다. 대조군(對照群)의 경우(境遇)에는 중의(中醫)가 회진(會診)하지 않았다. 14개월(個月)동안 모두 실험군(實驗群) 23례(例)와 대조군(對照群) 16례(例)를 대상(對象)으로 연구(硏究)를 하였는데, 모두 여성환자(女性患者)였다. 압축성폐용량(壓軸性肺用量)(FVC), 폐총용량(肺總用量)(TCL), carbon monoxide에 대(對)한 폐(肺)의 확산능력(擴散能力)(DLCO), 그리고 폐포공기량(肺泡空氣量)(VA)에 대(對) DCLO의 비(比)를 지표(指標)로 삼아, 폐기능(肺氣能)의 손상정도(損傷程度)에 따라서 box plot으로 분석(分析)하고, 폐기능(肺氣能)의 손상(損傷)을 측정(測定)하는 시스템을 만들었다. 실험결과(實驗結果), 실험군(實驗群)이 대조군(對照群)에 비(比)해서 치료(治療) 전(前)보다 명현(明顯)한 개선(改善)이 있었다. 폐기능(肺氣能)을 검사(檢査)한 수치(數値)들을 일반적(一般的)으로 통계처리(統計處理)한 것을 응용(應用)하고, TCL과 FVC의 모형식(模型式)을 만든 결과(結果), 실험군(實驗群)에서 FVC가 치료과정(治療過程)의 기간(其間)과 정비례(正比例)하여 향상(向上)되고, 또한 치료효과(治療效果)가 명현(明顯)하게 나타나기 시작(始作)하는 시기(時期)가 중의(中醫) 치료과정(治療過程)을 거친 실험군(實驗群)의 제(第)12개(個)에서 DLCO와 DLCO/VA의 향상(向上)이 나타나는 시기(時期)와 거의 일치(一致)하는 것을 발견(發見)하였다.