• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.35-42
• /
• 2011

Recently, the Next Generation High Speed Train(hereinafter HEMU-400X) which has been developing is the power distribution type high speed train. The power is on every each car and all bogies are installed on the front and rear of every car comparison with KTX and KTX-Sancheon which are consist of power cars and linkable bogies. HEMU-400X can be designed much more seats than others because there are not power car separately. However, that type has no advantage for vibration and noise due to distributed power and more faster design speed. Therefore, in this study, the design of floor construction for preventing the vibration from under the floor is considered.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1000-1005
• /
• 2010

Ride comfort is an important factor for the development of a high-speed train. The aerodynamic force to a high speed train inside tunnels increases the car-body vibration and makes its ride comfort worse. In this study, the aerodynamic force is estimated through a CFD analysis using ADINA, and its car-body vibration and ride comfort are calculated for the aerodynamic force which acts on the side of the train. The numerical results show that the vibration is a lateral mode of the car-body and decreases the ride comfort. On the basis of this numerical simulation, more accurate simulation is necessary for the shape of tunnel and the lateral suspension system of a high speed train.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.194-201
• /
• 2002

In this study is presented a numerical method which assesses running safety of the freight car loading with loom CWR and structural safety of conventional railway track and fastening when passing over sharp curves and steel girder bridges. Optimal speed of the freight car is suggested based on the numerical reviews of the safety against derailment of the freight car and structural safety of track and fastening at vulnerable points of the conventional line.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.551-562
• /
• 2000

The study was carried out about the design of power Car for Korean High Speed Train of maximum operating speed of 350km/h. The running resistance accounts toy the greater part of overall resistance to front hue motion. So, The Power Car's shape has to be mainly determined by aerodynamic considerations. In the train configuration of the KHST, the front and rear power cars assume the role of a locomotive. They accommodate all the machinery for providing traction. The train is controlled and monitored from power cars. This report was descrived, which focuses on aerodynamics, mass balance, the car body and the layout of the equipment that is fitted into power car.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.109-113
• /
• 2003

Recently, freight cars for diverse purposes were developed to increase the speed of freight car in conventional line. The welded type bogies are applied to these vehicles like container car, gondola car, hopper car, etc. This study was focused on the dynamic characteristics and the stability of freight car to guarantee the running safety. We have conducted the running tests of freight cars in conventional line and described the test results in this paper.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.1
• /
• pp.61-67
• /
• 2012

The in-wheel motor used in green car was designed and constructed for an electric direct-drive traction system. It is difficult to connect cooling water piping because the in-wheel motor is located within the wheel structure. In the air cooling structure for the in-wheel motor, a outer surface on the housing is provided with cooling grooves to increase the heat transfer area. In this study, we carried out the analysis on the fluid flow and thermal characteristics of the in-wheel motor under the effects of motor speed and heat generation. In order to check the problem of heat release, the analysis has been performed using conjugate heat transfer (conduction and convection). As a result, flow fields and temperature distribution inside the in-wheel motor were obtained for base speed condition (1250 rpm) and maximum speed condition (5000 rpm). Also, the thermo-flow characteristics analysis of in-wheel motor for vehicles was performed in consideration of ram air effect. Therefore, we checked the feasibility of the air cooling for the housing geometry having cooling grooves and investigated the cooling performance enhancement.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.302-307
• /
• 2004

When trains run over a snow-covered track at high speed, the snow accereted under car bodies may drop during train running. The dropped snow/ice lumps scatter the ballast on the track damaging the car body and the environment along the track in snowy regions. In this study, the snow-fall condition in winter around the Seoul-Busan high-speed line has been investigated to yield the countermeasure for the high-speed line. The climate near Japanese and French high-speed line as well as the relationship between the climate and countermeasure has also been investigated and the direction of countermeasure for Seoul-Busan high-speed line has been deduced. Consequently, the amount and frequency of snow-fall near Seoul-Busan high-speed line is less than that of Japan and France, so the speed restriction could be the fundamental countermeasure for Seoul-Busan high-speed line, and additional measure on rolling stock and infrastructure should be followed.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.1
• /
• pp.33-39
• /
• 2014

Automatic driving needs many functions such as the obstacle recognition, the lane recognition, and the lane change, etc. In this paper, we realized a system which automatically drove the three-kinds of vehicle driving course, to introduce and apply the concept of 'color recognition' that expands the scope of 'lane recognition' for vehicle driving. We made the reduced each course compared with RC(Radio Control) car size, and controlled the steering considering the position and the slope of the detection line and the speed. Because the RC car does not have the brake function, we consider the speed and the position of the detection line to stop the RC car.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.623-625
• /
• 1997

This paper deals with the simulator for the diagnosis systems of high speed train. The purpose of this simulator is the verification of diagnosis systems. In this paper, the configuration of high speed train is investigated and the implementation model of power car is proposed. According to the model, mathematical equation is constructed. Dynamic simulation is executed and analyzed.

• Science of Emotion and Sensibility
• /
• v.17 no.1
• /
• pp.29-38
• /
• 2014

In recent days, according as ergonomics and aesthetic engineering are important factors in the product market, there is a demand to develop automobile seat and interior designs which are focused on sensitive elements such as aesthetic and comfort features in order to satisfy the sensitive needs of consumers. To meet such demands, car seats are turning into functional and sensitive products that reflect elements of function and entertainment. According to such trends, this research is aimed to develop the illuminating car seat fabric that serve such functions as recognizing and reacting to car environments, which includes sensing over-speed, open doors, and unfastened safety belts through the illuminating car seat fabrics by optical fiber. For this purpose, basic physical properties of optical fiber are analyzed, appropriate weaving and etching technologies are applied, and the woven fabric of optical fiber for car seats are illuminating depend upon car environments. Moreover, the applicable woven fabric of optical fiber is deduced after evaluating the physical properties (such as tensile strength, heatproof, anti-fouling, washable and combustible traits) for the appropriateness of applying the woven fabric of optical fiber to car seats. For this purpose, the woven fabric of optical fiber is covered according to car seat processes; the optical fiber applied to seats is composed that it may be connected to one end of the connector linked to a LED so that it may perform functions like sensing over-speed, open doors, and unfastened safety belts; the sensed signals are transmitted to the control part, and luminescent signals are transmitted to LED.