• Journal of the Korean Geotechnical Society
• /
• v.26 no.2
• /
• pp.23-32
• /
• 2010

This study was especially conducted to find out the characteristics of the lightweight air-mixed soil (slurry density 10 kN/$m^3$) containing silt related to water. Compression strength, permeability, and capillary height of the lightweight air-mixed soil were studied, and also to support these studies, the structure of that soil was analyzed in detail. Air bubbles of various sizes are inside the lightweight air-mixed soil, and its distribution in a location is almost constant. A numerous tiny pores are inside the air bubbles so that the lightweight air-mixed soil can be saturated with water. Porosity is also estimated through the image analysis. Peak strength of the lightweight air-mixed soil is not dependent on water, but behavior of stress-strain is affected by the water. Permeability is about $4.857{\times}10^{-6}cm/sec$, which is a little bit higher than the clay's permeability. Capillary rise occurs rapidly at the beginning of the test until the lapse of 100 minutes and then its increase rate becomes slow. The capillary rise causes the increase of the density of the lightweight air-mixed soil, and thus it is required to pay attention to this phenomenon during structure design and maintenance of the lightweight air-mixed soil.

• Journal of Power System Engineering
• /
• v.2 no.3
• /
• pp.34-40
• /
• 1998

Performance characteristics of a refrigeration systems with various expansion valves and superheat changes were investigated experimentally. Experimental data have been taken utilizing three different devices; a thermostatic expansion valve, a linear type electronic expansion valve and a solenoid type electronic expansion valve. The data taken from tile three types of expansion valves were discussed with the temperature distribution of each zone in the evaporator and the superheat changes of the evaporator outlet In each zone temperature distribution fluctuated larger with the thermostatic expansion valve than with the electronic expansion valves. The optimum superheat ranged from $5^{\circ}C\;to\;15^{\circ}C$, and the superheat with the thermostatic expansion valve showed hunting phenomenon, which affected the evaporating and condensing temperature.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.2.1-2.1
• /
• 2011

Electrospray deposition (ESD) technique is fast finding its applicability in the field of thin film device manufacturing processes and the ease and cost efficiency attached to ESD process with possible integration with batch manufacturing technologies is the potential future of thin film device manufacturing. As the name suggests, the deposition phenomenon should solely be a spray achieved through electrostatic forces. In fact it is an imbalance between the surface forces arising because of the surface tension of the liquid to be sprayed and Maxwell stresses which are induced because of the electric field, that pull the liquid downwards from the capillary into a stable jet which further disintegrates into smaller droplets because of coulomb forces and hence a cloud of charged, mono-dispersed and extremely diminutive (sometimes up to femtolitres) droplets is achieved. The present talk is going to be exclusively about the electrospray process concepts, generation and possible applications.

• Transactions of Materials Processing
• /
• v.19 no.2
• /
• pp.73-78
• /
• 2010

Recently, many researches on the development of super-hydrophobic surface have been concentrated on the fabrication of nano-patterned products. Nano-patterned mold is a key to replicate nano-patterned products by mass production process such as injection molding and UV molding. The present paper proposes the new fabricating method of nano-patterned mold at low cost. The nano-patterned mold was fabricated by electroforming the anodic aluminum oxide membrane filled with UV curable resin in nano-hole by capillary phenomenon. As a result, the final mold with nano-patterns which have the holes with the diameter of 100~200 nm was fabricated. Furthermore, the UV-molded products with clear nano- patterns which have the pillars with the diameter of 100~200nm were achieved.

• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.140-147
• /
• 2018

The performance of a hydrate anti-agglomerant (AA) on cyclopentane (CyC5) hydrate anti-agglomeration at various concentrations (0-1 wt%, based on the oil phase) using MMF apparatus has been investigated. At low AA concentrations up to 0.01 wt%, the AA reduces the cohesion force (capillary force) by reducing the CyC5-water interfacial tension. At concentrations higher than 0.1 wt%, hydrate hydrophobicity alternation and AA's thermodynamic inhibition effects are the main part of AA's mechanism. Additionally, a "temporary agglomeration" phenomenon caused by surface melting of the hydrate particles is also observed, which may indicate the AA's weak ability to produce stable water-CyC5 interface.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.1
• /
• pp.57-62
• /
• 1990

This paper deals with the flow caused by a two-dimensional pulsating source, which moves with a constant horizontal speed beneath the free surface. The analysis is based on lincar potential theory including surface tension effects. In the case of subcritical reduced frequencies $\tau<1/4(\tau=U_{\omega}/g$, U=constant speed, $\omega$=circular frequency, g=gravitational acceleration), six wave components arc found. Two of them are largely affected by surface tension, which propagate ahead of the source in the direction of and opposite to the steady translation, respectively. The rest are almost identical with those found by Haskind(1954), i.e. for which the surface tension effect is negligible. For low oscillation frequencies, the resonant frequency still exists at $\tau$ only slightly greater than 1/4. For oscillation frequencies greater than $\nu(={\omega}^2/g)>20$, the surface tension effect is so significant that it disperses generated waves and consequently the singular phenomenon is removed. However, in addition to the gravity breaking, capillary breakings occur when the translation speed coincides with the minimum capillary celerity.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.255-264
• /
• 2009

Soils containing vanishing materials lead changes in the microstructure of particulate media due to water inflow. Thus, dissolution renders some local unstability. As the moisture contents decease, the component of the vanished materials may affects on the cementation of paniculate materials. This cementation phenomenon has a huge influence on the stiffness, strength and stability under lower stress level. The goal of this study is to introduce the cementation effects on a compressional wave velocity, a shear wave velocity, and the resonant frequency of shear waves. The glass bead and salt water with different mole contents are used. Test results show that the changes of shear and compressional wave velocities consist of three stages. In the first region, compressional wave velocities increase and shear wave velocities decrease with a decreases in reducing water contents from 100% to 90~95%. In the second region, shear and compressional wave velocities become stable at 90~95% to 10% of the water contents. In the third region, shear and compressional wave velocities increases dramatically with a decrease in the water content due to the capillary force and cementation of salt. Furthermore, the resonant frequency of the shear waves shows similar phenomenon. Specimens prepared by glass beads and salt water are proved to be able to provide a meaningful insight in under structural behaviors of the cementation.

• Journal of ILASS-Korea
• /
• v.11 no.2
• /
• pp.89-97
• /
• 2006

An inviscid axisymmetric model capable of predicting droplet bouncing and the detailed pre-impact motion, influenced by the ambient pressure, has been developed using boundary element method (BEM). Because most droplet impact simulations of previous studies assumed that a droplet was already in contact with the impacting substrate at the simulation start, the previous simulations could not accurately describe the effect of the gas compressed between a failing droplet and the impacting substrate. To properly account for the surrounding gas effect, an effect is made to release a droplet from a certain height. High gas pressures are computationally observed in the region between the droplet and the impact surface at instances just prior to impact. The current simulation shows that the droplet retains its spherical shape when the surface tension energy is dominant over the dissipative energy. When increasing the Weber number, the droplet surface structure is highly deformed due to the appearance of the capillary waves and, consequently, a pyramidal surface structure is formed; this phenomenon was verified with our experiment. Parametric studies using our model include the pre-impact behavior which varies as a function of the Weber number and the surrounding gas pressure.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.4
• /
• pp.134-140
• /
• 2009

The feasibility of electrochemical drilling and milling on stainless steel are investigated using tungsten microelectrode with $10{\mu}m$ in diameter. For the development of environmentally friendly and safe electrochemical process, citric acid solution is used as electrolyte. A few hundred nanoseconds duration pulses are applied between the microelectrode and work material for dissolution localization. Tool fracture by Joule heating, micro welding, capillary phenomenon, tool wandering by the generated bubbles are observed and their effects on micro ECM are discussed. Occasionally, complex textures including micro pitting corrosion marks appeared on the hole inner surface. Metal growth is also observed under the weak electric conditions and it hinders further dissolutions for workpiece penetration. By adjusting appropriate pulse and chemical conditions, micro holes of $37{\mu}m$ in diameter with $100{\mu}m$ in depth and 26Jim in diameter with $50{\mu}m$ in depth are drilled on stainless steel 304. Also, micro grooves with $18{\mu}m$ width and complex micro hand pattern are machined by electrochemical milling.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.252-252
• /
• 2012

It is widely accepted that short exciton diffusion lengths of organic semiconductors with respect to the film thickness limit the charge (hole and electron) separation before excitons recombination in organic photovoltaic (OPV) cells. Therefore the efficient absorption of incident light within the thin active organic layer is of great importance to improve the power conversion efficiency (PCE) of the cells. In this work, we fabricated 2-dimensionally (2D) nano-patterned poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOST:PSS) layers using capillary phenomenon and nano-imprinting technology at the scale of several hundred nanometers. This 2D nano-patterned PEDOT:PSS layer exerted photonic crystal effect such as redirection of light paths and variation of light intensity at specified wavelengths. It is also expected that the consequently alternated light pass lengths and intensities change the absorption properties of zinc phthalocyanine (ZnPc) thin films grown on top of the nano-patterned PEDOT:PSS layer. The influence of conductivity and thickness of the PEDOT:PSS layer on the absorption properties of ZnPc thin films were also investigated.