• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.372-377
• /
• 2008

Camber with positive deflection is one of the very important design parameters in the manufacture of railway coach. Positive camber is defined as concave shape such as an arch and it increases the strength of structure remarkably. But during the operation of a structure, the positive camber turns into negative camber and it loses the strength of structure. Therefore we should consider the camber effect when we evaluate the fatigue strength of negative cambered structure. For this purpose, we made a model of negative cambered locomotive car body and performed structural analysis and also we measured the dynamic loads at critical points during commercial line operation. Fatigue strength of locomotive was calculated by applying Miner's damage accumulation rule. Fatigue strength of the two locomotives which have different camber were compared to find out the effect of camber on dynamic load amplitude. We found that the more negative camber a locomotive had, the shorter fatigue strength obtained.

• Tribology and Lubricants
• /
• 제26권1호
• /
• pp.56-60
• /
• 2010

Contact pressure occurs whenever two surfaces contact between cam and roller. Especially excessive pressure peaks occur at the ends of the contact region. Such as scuffing or pitting will be induced when these operating conditions continuously occur on the surface. Camber effect is given to reduce damage by changing the shape of roller. The objective of this paper is to calculate contact pressure distribution by using a contact analysis considering camber and tilting angle. These results predict that camber effect of all machine components have influence on contact pressure distribution.

• 한국세라믹학회지
• /
• 제34권6호
• /
• pp.601-610
• /
• 1997

In cofiring of multilayered alumina with tungsten, the change of camber with lamination condition was experimented and the effect of sintering shrinkage of alumina and tungsten was investigated. From the exact measurement of sintering shrinkage of tungsten thick film, as lamination pressure increased, the sintering shrinkage of alumina decreased but that of tungsten thick film was not changed. So it was though that the main factor which induced the sintering shrinkage difference between ceramics and metal with lamination condition was the change of sintering shrinkage of ceramics. In case of high lamination pressure, high green sheet density, the cofired specimen showed low camber due to low shrinkage difference between alumina and tungsten and there was a linear relation between camber and shrinkage difference. It was found that this shrinkage difference could change the thickness of tungsten film and the microstructure within via hole during cofiring.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.688-693
• /
• 2001

It is almost impossible to have a straight web for processing in the continuous process systems. The cambered web usually causes the strip walking and damage during process. It is necessary to identify the lateral dynamics of the cambered web for the precise control of lateral behavior. In this paper, a dynamic model of the lateral behavior for a cambered web is developed by introducing the concept of steering angle equivalent to moment caused by the camber. This model can be extended to include terms associated with moment, induced by roller's tilting, web slippage, and shear force, etc. Using this model, a new feed-forward controller is proposed to enable the on-line camber estimation, which is difficult to be measured directly, and the prediction of lateral deflection caused by camber. Computer simulation study shows that the proposed controller successfully eliminates the effect of camber and has better control performance than that of the existing PID controller.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.917-918
• /
• 2010

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.387-394
• /
• 2000

Theoretical and experimental study is conducted on the contact pressure distribution of a radial tire in motion under various camber angles. Tire construction is modelled by a spring bedded elastic ring, consisted of sidewall springs and a composite belt ring. The contact area is assumed to be a trapezoidal shape varying with camber angles and weighted load. The basic equation in a quasi-static form is derived for the deformation of a running belt with a constant velocity by the aid of Lagrange-Euler transformation. Galerkin's method and stepwise calculation are applied for solving the basic equation and the mechanical boundary condition along both sides of the contact belt part subjected to shearing forces transmitted from the sidewall spring. Experimental results on the contact pressure, measured by pressure sensors embedded in the surface of the drum tester, correspond well with the calculated ones for the test tire under various camber angles, running velocities and weighted loads. These results indicate that a buckling phenomenon of the contact belt in the widthwise direction occurs due to the effect of camber angle.

• 한국정밀공학회지
• /
• 제12권5호
• /
• pp.88-97
• /
• 1995

The leaf spring is used in the suspension of most buses and trucks due to its compactness, which reduces the shock-force and the vibration from the road, and increases passenger comfortability and carlife. Of the various kinds of leaf springs, the leaf spring without eyes can be found easily in the heavy duty truck, and has different characteristics to the leaf spring with eyes in the case of large free camber. Because of radius change, the leaf without eyes slips on the supports, which makes the deflection. The difference is due to this deflection. In this paper, we show the general method of characteristic analysis, for example, Pandan method, can be no more applicable to these springs. Thus considering the geometry deflection by slip, we have developed the equation of the characteristic of the leaf spring without eyes and prove the effectiveness of this equation by experiment. From the result, at large camber the slip deflection is large and as camber smaller, this is smaller. At the camber behind some value, the effect of slip no longer influence to the characteristic of leaf springs.

• 한국재료학회지
• /
• 제33권12호
• /
• pp.537-549
• /
• 2023

The sintering shrinkage behaviors of low temperature cofired ceramics (LTCC) and resistors were compared using commercial LTCC and thick-film resistor pastes, and factors influencing the camber of cofired resistor/LTCC bi-layers were also investigated. The onset of sintering shrinkage of the resistor occurred earlier than that of LTCC in all resistors, but the end of sintering shrinkage of the resistor occurred earlier or later than that of LTCC depending on the composition of the resistor. The sintering shrinkage end temperature and the sintering shrinkage temperature interval of the resistor increased as the RuO₂/glass volume ratio of the resistor increased. The camber of cofired resistor/LTCC bi-layers was obtained using three different methods, all of which showed nearly identical trends. The camber of cofired resistor/LTCC bi-layers was not affected by either the difference in linear shrinkage strain after sintering between LTCC and resistors or the similarity of sintering shrinkage temperature ranges of LTCC and resistors. However, it was strongly affected by the RuO₂/glass volume ratio of the resistor. The content of Ag and Pd had no effect on the sintering shrinkage end temperature or sintering shrinkage temperature interval of the resistor, or on the camber of cofired resistor/LTCC bi-layers.

• Computers and Concrete
• /
• 제30권6호
• /
• pp.445-453
• /
• 2022

A pre-cambered deep deck-plate system has been developed that can realize a long span by offsetting the deflection caused by a construction load. In this study, finite element (FE) analysis is performed to examine the preload-camber relationship introduced into a deck and calculate the deflection reflecting the ponding effect that arises during concrete pouring. The FE analysis results showed that the stress of the bottom plate was half of the yield stress when the pre-camber of approximately 30 mm was introduced. Based on the FE results, a full-scale deep deck-plate is fabricated, a pre-camber is introduced, and concrete is poured to measure deflection. A deflection calculation formula that reflects the ponding effect is proposed, and the deflections yielded by the proposed model, experimental results, and FE results are compared. Results show that the proposed model can accurately estimate the deflection of non-supported deep deck-plate systems after concrete is poured.

• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.229-240
• /
• 1991

본 연구에서 사용한 이론과 제시된 방법의 타당성을 검토하기 위하여 익열 간 극이 무한대인 단일 익형 주위의 유동장을, 최근에 개발된 계산방법인 Lambda방법을 사용한 Dadone의 해석결과와 비교하였고, 범용의 압축기 익형인 NACA65게열 익열 유동 에 대한 Herrig의 실험값, 그리고 미분해석에 의한 점성-비점성 상호작용 방법을 사용 한 Hansen의 계산값고, 이들 조건과 동일한 상태에서 본 연구에서 제시한 방법으로 계 산한 결과와 만족할 만한 일치를 얻었다.