• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.3
• /
• pp.261-268
• /
• 1995

In transforming $K_2Ti_4O_9$ whisker, synthesized by calcination and slow cooling method, into $K_2Ti_6O_{13}$ whisker with boiling water and hydrochrolic acid, the effect of their treatment time and concentration on phase transformation, surface state and scattering of whisker was examined. The result was that the surface state of whisker was improved and whisker with a small diameter and a considerable aspect ratio was obtained by inducing scattering of a bundle of whisker. The treatment by boiling water and hydrochrolic acid induced the phase transformation of $K_2Ti_4O_9$ into $K_2Ti_6O_{13}$ and the phase transformation proceeded by extration of $K^+$ ion.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.8
• /
• pp.639-645
• /
• 2012

Embossed $TiO_2$ thin films with high surface areas are achieved using soft-templates composed of monolayer polystyrene beads. The form of links between the beads in the templates is controlled by varying the $O_2$ plasma etching time on the templates, resulting in various templates with close-linked, nano-linked, and isolated beads. Room-temperature deposition of $TiO_2$ on the plasma-treated templates and calcination at $550^{\circ}C$ result in embossed films with tailored links between anatase $TiO_2$ hollow hemispheres. Although all the embossed films have similar surface areas, the sensitivity of films with nano-linked $TiO_2$ hollow hemispheres to 500 ppm CO and ethanol gases are much higher than that of films with close-linked and isolated hollow hemispheres, and the detection limits of them are as low as 0.6 ppm for CO and 0.1 ppm for ethanol. The strong correlation of sensitivity with the form of links between hollow hemispheres reveals the critical role of potential barriers formed at the links. The facile, large-scale, and on-chip fabrication of embossed $TiO_2$ films with nano-linked hollow hemispheres on Si substrate and the high sensitivity without the aid of additives give us a sustainable competitive advantage over various methods for the fabrication of highly sensitive $TiO_2$-based sensors.

• Journal of Powder Materials
• /
• v.23 no.1
• /
• pp.38-42
• /
• 2016

$BaTiO_3$-coated Fe nanofibers are synthesized via a three-step process. ${\alpha}-Fe_2O_3$ nanofibers with an average diameter of approximately 200 nm are first prepared using an electrospinning process followed by a calcination step. The $BaTiO_3$ coating layer on the nanofiber is formed by a sol-gel process, and a thermal reduction process is then applied to the core-shell nanofiber to selectively reduce the ${\alpha}-Fe_2O_3$ to Fe. The thickness of the $BaTiO_3$ shell is controlled by varying the reaction time. To evaluate the electromagnetic (EM) wave-absorbing abilities of the $BaTiO_3@Fe$ nanofiber, epoxy-based composites containing the nanofibers are fabricated. The composites show excellent EM wave absorption properties where the power loss increases to the high frequency region without any degradation. Our results demonstrate that the $BaTiO_3@Fe$ nanofibers obtained in this work are attractive candidates for electromagnetic wave absorption applications.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.6
• /
• pp.357-362
• /
• 2015

A novel $TiO_2$-Coconut Shell Powder Composite (TCSPS), prepared by the controlled sol-gel method with subsequent heat treatment, was evaluated as an innovative photocatalytic absorbent for the removal of methylene blue. Optimal preparation conditions of TCSPC were obtained by a response surface methodology and a central composite design model. As compared with the results obtained from one-factor-at-a-time experiments, the values were approximated to the nearest condition of these values and the following experimental parameters were set as the optimum : $600^{\circ}C$ calcination temperature and 20 g of coconut shell powder loading amount.

• Journal of Korean Society on Water Environment
• /
• v.25 no.3
• /
• pp.404-410
• /
• 2009

In this study, research for physical and chemical characteristics were conducted through analysis of sediments, grading and heavy metals (e.g., Mn, Cu, Cd, Zn and Pb ) in sewers which are classified by drainage types. After that, cement solidification and yellow soil calcinations made heavy metals stabilized and then, ways of recycling it were examined. The grain size distribution of all sediments was relative graded. When evaluating heavy metal pollution through index of geoaccumulation (Igeo), Cu showed moderately pollution or strong pollution in forest and street site and Zn was assessed by moderately pollution in military, residential, and street site. Analysis of Pearson Correlation coefficient of heavy metal indicated that all items in street site have tight relationship respectively. Especially, Cd-Zn, Cu-Pb, Cu-Mn, and Pb-Mn have relationship at 99% confidence intervals in statistical analysis. Recycling it with cement solidification was satisfied with compressive strength standard under 55% deposit contents and Zn, Pb, Mn were stabilized effectively. If time and temperature plasticity and compressive strength would be standard, it is revealed that yellow soil calcinations is valuable aggregate when it has 50-60 Wt% contents. When considering economic feasibility and stabilization of heavy metals, cement solidification would be more appropriate than yellow soil calcinations as solution to recycling.

• Korean Journal of Materials Research
• /
• v.21 no.8
• /
• pp.425-431
• /
• 2011

The industrial manufacturing of YSZ products can be summarized as a three step process: a) hydrolysis of zirconyl chloride and mixing of other solutions, b) precipitation, and c) calcination. The addition of ammonia or OH- is essential in the precipitation process. However, a strong agglomeration was observed in the results of an ammonia or OH- addition. Thus, it is necessary to disperse the powders smoothly in order to improve the mechanical strength of YSZ. In this study, YSZ was synthesized using the urea stabilizer and hydrothermal method. YSZ powders were synthesized using a hydrothermal method with Teflon Vessels at $180^{\circ}C$ for 24 h. The mole ratio of urea to Zr was 0, 0.5, 1, and 2. The crystal phase, particle size, and morphologies were analyzed. Rectangular specimens ($33\;mm{\times}8\;mm{\times}1{\pm}0.5\;mm$) for three-point bend tests were used in the mechanical properties evaluation. The crystalline of YSZ powders observed a tetragonal phase in the sample with a ratio of Zr:urea = 1:2 addition and a hydrothermal reaction time of 24 h. The average primary particle size of YSZ was measured to be 9 nm to 11 nm. The agglomerated particle size was measured from 15 nm to 30 nm. The three-point bending strength of the YSZ samples was 142.47 MPa, which is the highest value obtained for the Zr:urea = 1:2 ratio addition YSZ sample.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.661-665
• /
• 2013

Effect of organic acid on the preparation of indium-oxalate salt from indium scraps generated from ITO glass manufacturing process was studied. Effects of parameters, such as type and concentration of organic acids, pH of reactant, temperature, reaction time on indium-oxalate salt preparation were examined. The impurity removal efficiency was similar for both oxalic acid and citric acid, but citric acid did not make organic acid salt with indium. The optimum conditions were 1.5 M oxalic acid, pH 7, $80^{\circ}C$, and 6 hours. On the other hand, the recoveries increased with pH, but the purity decreased. The indium-oxalate salt purity prepared by two cycles was 99.995% (4N5). The indium-oxalate salt could be converted to indium oxide and indium metal by substitution reaction and calcination.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.667-671
• /
• 2013

We present an easy method of preparing two-dimensional (2D) periodic hollow tin oxide ($SnO_2$) hemisphere array gas sensors using polystyrene (PS) spheres as a template. The structures were fabricated by the sputter deposition of thin tin (Sn) metal over an array of PS spheres on a planar substrate followed by calcination at an elevated temperature to oxidize Sn to $SnO_2$ while removing the PS template cores. The $SnO_2$ hemisphere array structures were examined by scanning electron microscopy and X-ray diffraction. The structures were calcined at various temperatures and their sensing properties were examined with varying operation temperatures and concentrations of nitric oxide (NO) gas. Their gas-sensing properties were investigated by measuring the electrical resistances in air and the target gases. The measurements were conducted at different NO concentrations and substrate temperatures. A minimum detection limit of 30 ppb, showing a sensitivity of S = 1.6, was observed for NO gas at an operation temperature of $150^{\circ}C$ for a sample having an Sn metal layer thickness corresponding to 30 sec sputtering time and calcined at $600^{\circ}C$ for 2 hr in air. We proved that high porosity in a hollow $SnO_2$ hemisphere structure allows easy diffusion of the target gas molecules. The results confirm that a 2D hollow $SnO_2$ hemisphere array structure of micronmeter sizes can be a good structural morphology for high sensitivity gas sensors.

• Journal of the Korean Ceramic Society
• /
• v.38 no.10
• /
• pp.921-927
• /
• 2001

An effect of ultrasonic irradiation for the extraction and synthesis of alumina from kaolin was investigated by comparing ultrasonic irradiation method and conventional method with the same factors as reaction time, reaction temperature, and acid concentration. The ultrasonic irradiation method accelerated alumina extraction in comparison to conventional method at $60{\sim}80^{\circ}C$ for $1{\sim}6\;h$ in $1{\sim}5\;M$ ${H_2}{SO_4}$. The characteristics of precipitates and calcined samples, synthesized under the ultrasonic irradiation method and the conventional method, were determined by the means of DTA/TG, XRD, SEM, PSA, BET, etc. Especially, the calcined sample synthesized under the ultrasonic irradiation method had smaller particle size and larger surface area than that synthesized under the conventional method.

• Journal of the Korean Ceramic Society
• /
• v.51 no.2
• /
• pp.88-96
• /
• 2014

Natural hydraulic lime (NHL) is produced by burning a form of low-grade limestone containing silica and alumina which, above certain temperatures, combine with calcium oxide. The resulting silicates and aluminates impart hydraulic properties to the product. This study aims to determine the calcined characteristics of NHL using domestic low-grade limestone with maximized hydraulic properties. Six types of low-grade limestone containing $SiO_2$ were selected and experiments were carried out with different burning temperatures and holding times. The burning temperature and holding time as the most suitable burning conditions were $1,200^{\circ}C$ to $1,300^{\circ}C$ and 3 to 7 h, respectively, for the manufacturing of NHL from domestic low-grade limestone. These results demonstrate the feasibility of NHL using domestic low-grade limestone to produce NHL.