• 전기학회논문지
• /
• 제57권2호
• /
• pp.184-190
• /
• 2008

The fault location algorithm based on stationary wavelet transform was developed to locate the fault point more accurately. The stationary wavelet transform(SWT) was introduced instead of conventional discrete wavelet transform(DWT) because SWT has redundancy properties which is more useful in noise signal processing. In previous paper, noise cancellation technique based on the correlation of wavelet coefficients at multi-scales was introduced, and the efficiency was also proved in full. In this paper, fault section discrimination and fault location algorithm using noise cancellation technique were tested by ATP simulation on real power cable systems. From these results, the fault can be located even in very difficult and complicated situations such as different inception angle and fault resistance.

• 한국강구조학회 논문집
• /
• 제19권5호
• /
• pp.435-454
• /
• 2007

본 연구에서는 국내 내진 설계규정에서 고려하고 있지 않은 근거리지진의 특성을 규명하고, 사장교 구조물에 미치는 영향을 검토하고자 한다. 대표적인 근거리 및 원거리지진의 실측자료를 선정한 후, 탄성 및 비탄성응답스펙트럼을 작성하여 지진기록의 특성을 분석하였다. 세 가지 형식의 사장교 및 실제 사장교 구조물을 대상으로 지진특성에 따른 응답해석을 수행하여 주요부재에 대한 응답특성을 비교 분석하였다. 또한 지진응답해석 결과를 이용하여 신뢰성해석을 수행하였으며, 신뢰성지수 및 파괴확률을 검토함으로써 대상 사장교 구조물의 내진 안전성을 정량적으로 평가하였다. 응답스펙트럼, 지진응답해석 및 신뢰성해석 결과에 의하면 근거리지진이 사장교 응답에 대한 영향은 기존의 원거리지진과는 상이한 양상을 보이고 있으므로, 사장교 구조물 설계 시 중요한 인자로 고려해야 할 것을 제시하고자 한다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 A
• /
• pp.412-414
• /
• 2004

In this paper, a novel algorithm of underground cable fault location based on the analysis of distributed parameter circuit is proposed. The proposed method makes voltage and current equations about core and sheath, and then establishes a function of the fault distance according to the analysis of fault conditions. Finally gets the solution of this function through Newton-Raphson iteration method. The effectiveness of proposed algorithm has been verified by Matlab program, and the cable parameters such as impedance and admittance are from EMTP simulation.

• 전기학회논문지
• /
• 제56권7호
• /
• pp.1191-1198
• /
• 2007

In this paper, the fault detection and noise cancellation algorithm based on wavelet transform was developed to locate the fault more accurately. Specially, noise cancellation algorithm was based on the correlation of wavelet coefficients at multi-scales. Fault detection, classification and location algorithm were tested by EMTP simulation on real power cable system. From these results, the faults can be detected and located even in very difficult situations, such as at different inception angle and fault resistance.

• 한국전자통신학회논문지
• /
• 제1권1호
• /
• pp.63-69
• /
• 2006

해저광케이블은 육상광케이블에 비해 장거리이며 광중계기 시스템으로 인해 흔히 사용하는 고장지점에서 후방으로 산란 빛으로 거리를 탐지하는 일반적인 OTDR(Optical Time Domain Reflectormeter)의 사용은 매우 제한적이다. 그래서 해저광케이블 시스템에서 광코어의 단선인 경우는 광중계기의 OTDR Path를 이용한 Coherent OTDR를 사용 고장위치 탐지하고, 광신호의 증폭을 위해 광중계기에 필요한 전력을 공급하는 해저광케이블 내의 동튜브(Copper Tube) 손상시에는 전류/전압특성, 단위정전용량등을 이용한 방법들이 사용된다. 이런 정보를 이용하여 해저광케이블의 고장 형태에 따른 적절한 탐지 기법을 제시하고자 한다.

• 대한안전경영과학회지
• /
• 제20권3호
• /
• pp.21-26
• /
• 2018

This paper describes result of a study on safety against a fire of charging cable for mobile phone for vehicle. Combustion on the USB cable in the car was happened while driving. Gas coming from the burning USB cable could be a reason which can make a secondary car accident since the driver also can be embarrassed while driving. In order to prevent a secondary car accident connected on the road, to research a reason why USB cable can emit gas and be burned in charging. We did simulation test with abnormal fault condition for the electronic component on the board in the USB cable. So we get the result from abnormal fault condition simulation test, for instance, shorted test for output terminal of 8 pin switch, shorted test for chip resistor after thermal aging in the condition $25^{\circ}C$, 93 % RH during 48 hours. To analysis the result of all test, Combustion on the USB cable was not the 8 pin but other electrical component such as a chip resistor. Therefore we guess that the reason for USB cable combustion in charging in a car was not 8 pin and a LED but another defective component.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 A
• /
• pp.593-594
• /
• 2006

High temperature superconducting(HTS) power cable is expected to be used for power transmission lines supplying electric power for densely populated cities in the near future. Commercializing of HTS power cable is coming. Simulation is required for safety before install of HTS power cable, a fabrication model used at the power system simulation. In this paper, we shows a single line-to ground fault analysis in the grid system which has a loom length HTS power cable. The authors developed a single line-to ground fault current calculation method which is considering the shield layer of HTS power cable. In the calculation, the T type equivalent circuit is used to derive the mutual inductance of the HTS power cable

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 D
• /
• pp.2225-2226
• /
• 2006

High temperature superconducting(HTS) power cable is expected to be used for power transmission lines supplying electric power for densely populated cities in the near future. Commercializing of HTS power cable is coming. Simulation is required for safety before install of HTS power cable, a fabrication model used at the power system simulation. In this paper, we shows a single line-to ground fault analysis in the grid system which has a loom length HTS power cable. The authors developed a single line-to-ground fault current calculation method which is considering the shield layer of HTS power cable. In the calculation, the T type equivalent circuit is used to derive the mutual inductance of the HTS power cable.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1259-1260
• /
• 2006

High temperature superconducting(HTS) power cable is expected to be used for power transmission lines supplying electric power for densely populated cities in the near future. Commercializing of HTS power cable is coming. Simulation is required for safety before install of HTS power cable, a fabrication model used at the power system simulation. In this paper, we shows a single line-to ground fault analysis in the grid system which has a 100m length HTS power cable. The authors developed a single line-to-ground fault current calculation method which is considering the shield layer of HTS power cable. In the calculation, the T type equivalent circuit is used to derive the mutual inductance of the HTS power cable.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1719-1720
• /
• 2006

High temperature superconducting(HTS) power cable is expected to be used for power transmission lines supplying electric power for densely populated cities in the near future. Commercializing of HTS power cable is coming. Simulation is required for safety before install of HTS power cable, 3 fabrication model used at the power system simulation. In this paper, we shows a single line-to ground fault analysis in the grid system which has a loom length HTS power cable. The authors developed a single line-to-ground fault current calculation method which is considering the shield layer of HTS power cable. In the calculation, the T type equivalent circuit is used to derive the mutual inductance of the HTS power cable.