• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(II)
• /
• pp.385-390
• /
• 2003

Recently, use of Continuous Welded rail(CWR) is increased for structural, economical reason but new problem is caused accordingly and phenomenon that give threat in traveling by ship stability of train is led. According as rail is prolonged, excessive relative displacement and longitudinal force can happen to rail by temperature change and external force. Specially, buckling or fracture of rail can happen in railroad bridges because relative displacement by bridge and properties of matter difference between rail grows and additional axial force happens to rail by behavior of bridge. According to several study, longitudinal force of rail in bridge is influenced with ballast resistance, elongation length, boundary condition, stiffness of framework. Non-linear behavior of ballast acts by the most important factor in interaction between rail and bridge. Therefore, must consider stiffness of bridge construction with non-linear characteristic of ballast and stiffness of base for accuracy with longitudinal force calculation and analyze. In this study, perform material non-linear analysis for longitudinal force of CWR and three dimensional buckling analysis to decide buckling force.

• 한국강구조학회 논문집
• /
• 제12권6호
• /
• pp.727-736
• /
• 2000

본 연구에서는 궤도의 좌굴해석 및 그 결과를 통해 열차하중이 직선 및 곡선 장대레일 궤도의 온도좌굴 거동에 미치는 영향에 대해 평가하였다. 차량을 고려한 온도좌굴 해석은 바퀴하중하에서 장대레일 궤도의 수직 처짐에 기인한 상향처짐을 결정하기 위해 유사정적 하중모델을 가정하였으며, 차량의 무게와 속도, 궤도의 곡률, 캔트, 그외의 열차와 궤도의 동적인 상호작용으로 인한 횡방향하중은 열차의 수직하중에 대한 수평하중 비에 포함하여 수행하였다. 수치적 해석을 통해 장대레일의 상부 및 하부좌굴온도를 구하였고, 이런 해석결과들을 기존의 열차하중을 포함하지 않은 정적 좌굴해석결과들과 비교하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.386-394
• /
• 2007

Due to the transportability problems, long rail shall be from base rail unit, which is normally 100m for regular rail and 300m for high speed rail. After these rail units are transported from the fabricator to the site, the field weld would be performed.axial stresses in the long rail is mainly from the temperature differences at various locations the long rail. Also the gaps between each welds cause secondary axial stresses in the rail. In addition to these, re-welds the fractured rails, rail buckling, irregular rail vibration, rail twist also result innonuniform axial stresses in the rail. To obtain the rail buckling stability, the rail stresses shall be released due to the resetting of CWR. Traditionally two resetting of CWR methods have been applied, the one is rail heater and the other is rail tenser. these methods, the latter has been recommended because it has less limitation in the rail length and it is easier to minimized the force differences. But even in this method, the calculation is cumbersome and is not easy to find out the rail stress distribution itself.refined methodsxial stress resetting in the long rail is studied and this study be easily applied in the real construction. From this approach, more rational rail maintenance system can be expected.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1058-1070
• /
• 2007

Internal and external railway management corporations are using the periodic replacement criteria of rail by accumulated passing tonnage and wear to maintain rails for servicing. However, internal the periodic replacement criteria of continuous welded rail(CWR) by accumulated passing tonnage is the one(50kg/m-5 million gross tonnage, 60kg/m-6 million gross tonnage) presented in Japan before. It was estimated with the fatigue life about 50kg N rail joints applied diesel train load but it wasn't applied to current conditions of track; elimination of rail joint, using the concrete slab track and operation of light train load and effect of welding, manufacturing technique, grinding of rail. Therefore, in this study, it was investigated the types of damage and cause in welded rails and examined standards and information resources. Also, this study presents preliminary data to revise the periodic replacement criteria of CWR by current accumulated passing tonnage in bending test of laid welded rail and a survey of track maintenance history of Seoul metro.

• 한국철도학회논문집
• /
• 제3권1호
• /
• pp.19-26
• /
• 2000

The rail temperature is important to preserve the joint gap for standard length of rail and to determine the installation temperature which has direct influence on the rail buckling and failure in welded part for continuous welded rail(CWR), Therefore, we have measured and investigated various characteristics of rail temperature for each kind of rail. As the results of this, the correlation between the atmosphere temperature and the rail temperature which is commonly used by Korean Railway should be reconsidered. Also, the daily highest '||'&'||' lowest rail temperature was occurred when each temperature is higher and when it's lower. For the light rail, the rail temperature by the sun-light increases quickly and decreases late. But the time where the highest temperature is attained is same. There are some differences between the shade and sunny place about 3.0∼4.0$\^{C}$. The temperature of rail web is almost close to the conversion rail temperature for rail expansion. The wind of 1 m/s has an influence on the rail temperature around 5$\^{C}$.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 춘계학술대회 논문집
• /
• pp.207-212
• /
• 2002

The actual buckling of the railroad track structure is suspected to be a complex interaction between the vertical, lateral and torsional modes. To make the analysis tractable, however, most studies restrict themselves to either the vertical or the horizontal plane. Based on a comprehensive and realistic three-dimensional track model developed in the previous study, three dimensional buckling analysis of CWR track subjected to temperature load was performed. Using the study on buckling temperature and mode, sensitivity of track components such as tie spacing, ballast resistance, stiffness of pad-fastening system and rail size were investigated.

• 한국철도학회논문집
• /
• 제11권3호
• /
• pp.326-333
• /
• 2008

본 논문은 누적통과톤수에 의한 레일교체기준 개정을 위한 기초 데이터를 제시하는데 목적이 있다. 본 연구에서는 국외의 누적통과톤수에 의한 레일교체기준의 산정근거를 조사하였으며, 일본에서 조사된 레일용접부 결합유형 및 원인과 국내 철도운영기관인 서울메트로의 궤도유지관리이력을 조사하여 실제 레일절손과 누적통과톤수의 상관관계를 분석하였다. 또한, 누적통과톤수 기준치에 도래한 노후레일 용접부를 현장에서 발췌하여 레일용접부 휨시험을 수행하였다. 그 결과, 누적통과톤수와 레일절손간의 상관관계는 뚜렷하지 않았으며 레일용접부의 시공불량에 의한 절손사례가 많은 것으로 분석되었다. 또한, 노후레일휨시험 결과 신규레일용접부에 비해 파괴강도가 $17{\sim}18%$만이 저하된 것으로 나타나 레안교체기준에 도래한 노후레일은 사용성 측면에서 충분한 내구성 및 내하력을 확보하고 있는 것으로 분석되었다.

• 한국과학교육학회지
• /
• 제30권6호
• /
• pp.739-751
• /
• 2010

이 연구는 예비교사들이 과학탐구에 대한 비판적 토론을 분석하는 것에 초점을 두고 있다. 약 3개월 동안 24명의 예비교사들은 7개의 그룹으로 나뉘어 개방적 탐구를 수행하였고, 이후 10회의 비판적 토론을 실시하였다. 모든 토론과정은 녹화하여 전사하여 분석되었다. 툴민의 논증분석틀과 인지적 논증분석틀을 이용하여 예비교사들의 탐구토론에 나타난 논증의 특징을 살펴보았다. 주요 결과는 다음과 같다. 첫째, 의미단위별 논증요소 분석에서 주장, 정당한 이유, 자료, 반박, 지원의 순서로 많이 제시되었다. 둘째, 대화 단위별 논증 구조에서 CW, CD, CDW, CWR, CR의 순서로 많이 제시되었다. 셋째, 비판적 탐구토론에서는 다른 토론활동보다 반론의 비율이 많이 제시되었다. 넷째, 두 번째 논증활동이 첫 번째 논증활동보다 질적 수준이 향상되었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제20권2호
• /
• pp.40-48
• /
• 2016

본 연구는 지진이 발생할 경우 장대레일교량에 있어 레일과 상판 간의 종방향 상호작용에 미치는 영향을 검토하기 위한 것으로, 해석모델에 여러 하중조합과 함께 지진하중을 적용함으로써 대상 철도교량 레일에서의 축방향 부가응력과 레일-상판 간 상대변위의 변화를 산출하였다. 해석 결과, 본 연구 대상 철도교량의 경우 철도시설공단에서 제시하고 있는 표준응답스펙트럼을 적용할 때 레일부가응력은 대부분의 하중조합에 대해 허용기준 내의 값을 보이고 있는 반면, 레일-상판 상대변위는 공단에서 제시하는 허용기준을 초과하고 있는 것으로 나타났다. 따라서 레일-상판 상대변위가 레일부가응력에 비해 상대적으로 더 허용기준을 만족시키기 어렵다는 것을 알 수 있었으며, 아울러 고베 대지진과 같은 큰 규모의 지진이 발생하면 레일부가응력과 레일-상판 상대변위는 허용기준을 충족시키지 못하므로 이에 대한 적절한 내진 대비가 필요하다.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2016년도 학술발표회
• /
• pp.519-519
• /
• 2016

Upper Chenab Canal (UCC) is a non-perennial canal in Punjab Province of Pakistan which provides irrigation water only in summer season. Winter and summer are two distinct cropping season with an average rainfall of about 161 mm and 700 mm respectively. Wheat-rice is common crop rotation being followed in the UCC command area. During winter season, groundwater and rainfall are the main sources of irrigation while canal and ground water is used to fulfil the crop water requirements (CWR) during summer. The objective of current study is to estimate how the irrigation water requirements (IWR) of the two crops are going to change under different conditions of temperature and rainfall. For this purpose, 12 different climatic scenarios were designed by combining the assumptions of three levels of temperature increase under dry, normal and wet conditions of rainfall. Weather records of 13 years (2000-2012) were obtained from PMD (Pakistan Meteorological Department) and CROPWAT model was used to simulate the IWR of the crops under normal and scenarios based climatic conditions. Both crops showed a maximum increase in CWR for temperature rise of $+2^{\circ}C$ i.e. 8.69% and 6% as compared to average. Maximum increment (4.1% and 17.51% respectively) in IWR for both wheat and rice was recorded when temperature rise of $+2^{\circ}C$ is coupled with dry rainfall conditions. March & April during winter and August & September during summer were the months with maximum irrigation requirements. Analysis also showed that no irrigation is needed for rice crop during May and June because of enough rainfall in this area.