• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.219-220
• /
• 2006

Laser surface hardening technologies have been used to improve characteristics of wear and to enhance the fatigue resistance for mold parts. The objective of this research work is to investigate the influence of the process parameters, such as power of laser and defocused spot position, on the characteristics of laser surface hardening for the case of SKD61 steel. CW Nd:YAG laser is selected as the heat source. The optical lens with the elliptical profile is designed to obtain a wide surface hardening area with a uniform hardness. From the results of the experiments, it has been shown that the maximum hardness is approximatly 740 Hv when the power, focal position and the travel of laser are 1,095 W, +1mm and 0.3 m/min, respectively. In addition, the hardening width using the elliptical lens was three time larger than that using the defocusing of laser beam.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.17-18
• /
• 2006

Laser welding of metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for metals with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the butt welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1400W of the laser power, 0.8m/min, 0.9m/min of welding speed and $4{\ell}$ in of pressure for shielding gas.

• Journal of Sensor Science and Technology
• /
• v.12 no.4
• /
• pp.185-190
• /
• 2003

Recently, sensors which use the infrared light, supersonic waves, and electromagnetic waves have been used for many applications to detect information of the object. For these sensors, the accompanying system which utilizes the sensor should be systematically developed. In this paper, a general microwave radar sensor system is briefly described, and then basic applications of a CW doppler radar sensor system are introduced. For the CW doppler radar sensor applications, a highly-stable, low-cost Dielectric Resonator Oscillator (DRO) has also been designed and implemented, which can be used for commercial microwave sensor systems. The implemented DRO has output power of +5.33 dBm at 12.67 GHz and phase noise of -108.5 dBc/Hz at the 100 kHz offset frequency.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.3
• /
• pp.58-63
• /
• 2007

GPS signal is vulnerable to intentional and unintentional interferences since it has a very weak signal power and its structure is well-known. Among the interference rejecting techniques, the ATF is being generally used as a pre-correlation technique. However, it does not have a design parameter relating to the notch width, resulting in the spectral loss around frequency of the interference. The IIR notch filter has a design parameter relating to the notch width and can generate a sharp notch for the CW interference. In this paper, an adaptive IIR notch filter is proposed and the performance is evaluated using software signal generator and real measurements.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.6
• /
• pp.427-435
• /
• 2016

Array Gain (AG) is a metric to measure the performance of an array of acoustic sensors. AG is affected by the configuration of array, frequency and array element spacing, and the directivity of the ambient noise. In this paper, an algorithm to calculate AG based on the spatial coherence is used, and the results are verified through sea-going experiment. The method using the spatial coherence can be used to consider the arbitrary shape of an array and directionality of ambient noise. In the sea-going experiment, the towed source was used to transmit the Continuous Wave (CW), and was received at the horizontal line array on the seabed. The ambient noise was measured between the source transmission. The experimental AG was calculated from the SNR (Signal to Noise Ratio) of single sensor and an array of sensors. Finally, the predicted AG is shown to agree with the experimental value of AG.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2006.04a
• /
• pp.105-110
• /
• 2006

우리나라에 GPS 위성측량이 도입되기 시작한 것은 최근에 이루어 졌으며 많은 발전을 해오고 있지만 해결해야 할 많은 문제점을 가지고 있다. 현재 우리나라의 GPS 위성측량의 사용에 있어서 여러 가지 문제점 중 현재 지구 주위를 운항하고 있는 24개의 GPS 위성으로 지상 어느 곳에서나 24시간 동안 위성신호를 수신할 수 있게 되었지만 고층 빌딩과 같은 도심 계곡, 복잡한 한국지형, 산악지역 등에서의 위성 장애물에 의한 신호의 차단으로 한계가 발생하고 있다. NAVSYNC의 CW25 GPS 수신기는 -156dBm이하의 신호강도에서도 확실한 위치 fix가 가능하고, 이러한 능력은 도심지나, 울창한 숲과 심지어는 건물 안과 같이 신호가 미약한 지역에서도 사용될 수 있다. 이에 본 연구에서는 Indoor GPS 수신기를 이용하여 측지분야에서 검증된 GPS측량방법을 통해 수신데이터를 비교 분석하고 수신기의 정밀도 향상에 관한 연구를 하고자 한다.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2006.05a
• /
• pp.84-89
• /
• 2006

GPS(Global Positioning System)는 이미 전 세계적으로 다양한 응용분야를 가지고 널리 사용되고 있다. 그러나 현재 지구 주위를 운항하고 있는 24개의 GPS 위성으로 지상 어느 곳에서나 24시간 동안 위성신호를 수신할 수 있게 되었지만 고층 빌딩과 같은 도심 계곡, 복잡한 한국지형, 산악지역 등에서의 위성 장애물에 의한 신호의 차단으로 한계가 발생하고 있다. NAVSYNC의 CW25 GPS 수신기는 -156dBm이하의 신호강도에서도 확실한 위치 fix가 가능하고, 이러한 능력은 도심지나, 울창한 숲과 심지어는 건물 안과 같이 신호가 미약한 지역에서도 사용될 수 있다. 이에 본 연구에서는 Indoor GPS 수신기를 이용하여 측지분야에서 검증된 GPS측량방법을 통해 수신 데이터를 비교 분석하고 수신기의 정밀도에 관한 연구를 하고자 한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1369-1375
• /
• 2004

For many years and primarily for economical reasons, Dissimilar Metal Welds have been used as transition joints in a variety of equipment and applications. But Dissimilar Metal Welds have several fabrication and metallurgical drawbacks that can often lead to in-service failures. For example, the most pronounced fabrication faults are hot cracks. Laser welding techniques have been characterised for various materials. In this paper, the laser weldability of STS304 stainless steel and SM45C at dissimilar metal welds using a continuous wave Nd：YAG laser are experimentally investigated. An experimental study was conducted to determine effects of welding parameters, on eliminating or reducing the extent welding zone formation at dissimilar metal welds and to optimize those parameters that have the most influence parameters such as focus length, power, beam speed, shielding gas, and wave length of laser were tested

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.8 s.173
• /
• pp.17-26
• /
• 2005

Dissimilar-metal welds(DHWs) are used widely in various industrial applications due to the pratical importance from the technical and economic aspect. However, DMWs have several fabricative and metallurgical drawbacks that can often lead to in-service failures. For example, the most pronounced fabrication faults are hot cracks. Recently, DMWs have used the various of heat source to decrease such as faults. In this paper, the weldability on dissimilar metal welds of Austenite stainless steel and Low carbon steel using a continuous wave Nd:YAG laser was experimentally investigated. Experiments were conducted to determine effects of welding parameters, on eliminating or reducing the extent welding zone formation at dissimilar metal welds and to optimize those parameters that have the most influence parameters such as focus length, power, beam speed, shielding gas, and wave length of laser.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.6
• /
• pp.119-126
• /
• 2004

The welding characteristics of Inconel 600 Alloy using a continuous wave Nd:YAG laser are experimentally investigated. The major process parameters studied in the present laser welding experiment were the positions of focus, laser power and travel speed of laser bean We measured the fusion zone size and its shape using an optical microscope for the observation of cross-sectional area. We performed two tests regarding the tension and the micro hardness for welding quality estimation. Then we measured residual stress in welds by electronic speckle pattern interferometry(ESPI). In conclusion the optimum butt welding process parameters were 0.5mm focus position, 1.6kW laser power, 1m/min travel speed and 5.5$\ell$/min assist gas discharge.