• Journal of Welding and Joining
• /
• v.32 no.3
• /
• pp.68-73
• /
• 2014

Among through silicon via (TSV) technologies, for replacing Cu filling method, the method of molten solder filling has been proposed to reduce filling cost and filling time. However, because Sn alloy which has a high coefficient of thermal expansion (CTE) than Cu, CTE mismatch between Si and molten solder induced higher thermal stress than Cu filling method. This thermal stress can deteriorate reliability of TSV by forming defects like void, crack and so on. Therefore, we fabricated SiC composite filling material which had a low CTE for reducing thermal stress in TSV. To add SiC nano particles to molten solder, ball-typed SiC clusters, which were formed with Sn powders and SiC nano particles by ball mill process, put into molten Sn and then, nano particle-dispersed SiC composite filling material was produced. In the case of 1 wt.% of SiC particle, the CTE showed a lowest value which was a $14.8ppm/^{\circ}C$ and this value was lower than CTE of Cu. Up to 1 wt.% of SiC particle, Young's modulus increased as wt.% of SiC particle increased. And also, we observed cross-sectioned TSV which was filled with 1 wt.% of SiC particle and we confirmed a possibility of SiC composite material as a TSV filling material.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.10
• /
• pp.1049-1056
• /
• 2014

Microelectronics components contain various materials with different coefficients of thermal expansion (CTE). Although a large amount of published data on the CTE of standard materials is available, it occasionally becomes necessary to measure this property for a specific actual material over a particular temperature range. A change in the temperature of a material causes a corresponding change in the output of the strain gage installed on the specimen because of not only the mechanical load but also the temperature change. In this paper, a detailed technique for CTE measurement based on these thermal characteristics of strain gages is proposed and its reliability is evaluated. A steel specimen, aluminum specimen, and copper specimen, whose CTE values are well known, were used in this evaluation. The proposed technique was successfully applied to the measurement of the CTE of a coreless package substrate composing of electronics packages.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.190-194
• /
• 2000

The fabrication process and thermal properties of 50∼76vo1% SiCp/Al metal matrix composites (MMCs) were investigated. The 50∼76vo1% SiCp/Al MMCs fabricated by pressure infiltration casting process showed that thermal conductivities were 85∼170W/mK and coefficient of thermal expansion (CTE) were ranged 10∼6ppm/K. Specially, the thermal conductivity and CTE of 71vo1%SiCp/Al MMCs were ranged l15∼156W/mK and 6∼7ppm/K, respectively, which showed a improved thermal properties than the conventional electronic packaging materials such as ceramics and metals.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.83-87
• /
• 1999

The fabrication process and thermal properties of 50~71vol% SiCp/Al metal matrix composites (MMCs) were investigated. The 50~71vol% SiCp/Al MMCs fabricated by pressure infiltration casting process showed that thermal conductivities were 118~170W/mK and coefficient of thermal expansion (CTE) were 9.5~$6.5{\times}10^{-6}/K$. Specially, the thermal conductivity and CTE of 71vol%SiCp/Al MMCs were 115~156W/mK and 6~$7{\times}10^{-6}/K$. respectively, which showed a improved themal properties than the conventional electronic packaging materials such as ceramics and metals.

• Nuclear Engineering and Technology
• /
• v.54 no.7
• /
• pp.2359-2366
• /
• 2022

Selecting graphite grades with superior irradiation characteristics is important task for designers of graphite moderation reactors. To provide reference information and data for graphite selection, the effects of irradiation on three fine-grained, iso-molded nuclear grade graphites, ETU-10, IG-110, and NBG-25, were compared based on irradiation-induced changes in volume, thermal conductivity, dynamic Young's modulus, and coefficient of thermal expansion. Data employed in this study were obtained from reported irradiation test results in the high flux isotope reactor (HFIR)(ORNL) (ETU-10, IG-110) and high flux reactor (HFR)(NRL) (IG-110, NBG-25). Comparisons were made based on the irradiation dose and irradiation temperature. Overall, the three grades showed similar irradiation-induced property change behaviors, which followed the historic data. More or less grade-sensitive behaviors were observed for the changes in volume and thermal conductivity, and, in contrast, grade-insensitive behaviors were observed for dynamic Young's modulus and coefficient of thermal expansion changes. The ETU-10 of the smallest grain size appeared to show a relatively smaller VC to IG-110 and NBG-25. Drastic decrease in the difference in thermal conductivity was observed for ETU-10 and IG-110 after irradiation. The similar irradiation-induced properties changing behaviors observed in this study especially in the DYM and CTE may be attributed to the assumed similar microstructures that evolved from the similar size coke particles and the same forming method.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.25-32
• /
• 2013

PURPOSES : The purpose of this study is to provide the method of how to measure the coefficient of thermal expansion of concrete using temperature compensation principle of electrical resistance strain gauge. METHODS : The gauge factor compensation method and thermal output(temperature-induced apparent strain) correction method of self-temperature compensation gauge were investigated. From the literature review, coefficient of thermal expansion measurement method based on the thermal output differential comparison between reference material(invar) and unknown material(concrete) was suggested. RESULTS : Thermal output is caused by two reasons; first the electrical resistivity of the grid conductor is changed by temperature variation and the second contribution is due to the differential thermal expansion between gauge and the test material. Invar was selected as a reference material and it's coefficient of thermal expansion was measured as $2.12{\times}10^{-6}m/m/^{\circ}C$. by KS M ISO 11359-2. The reliability of the suggested measurement method was evaluated by the thermal output measurement of invar and mild steel. Finally coefficient of thermal expansion of concrete material for pavement was successfully measured as $15.45{\times}10^{-6}m/m/^{\circ}C$. CONCLUSIONS : The coefficient of thermal expansion measurement method using thermal output differential between invar and unknown concrete material was evaluated by theoretical and experimental aspects. Based on the test results, the proposed method is considered to be reasonable to apply for coefficient of thermal expansion measurement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.209-210
• /
• 2009

• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.76-85
• /
• 2014

In this paper, the equivalent coefficient of thermal expansion (CTE) of fiber reinforced plastic composite material is investigated with various CTE prediction schemes. Although there are several methods for predicting the equivalent CTEs, most of them have some limitations of are not much accurate when comparing prediction results with test results. In the framework of computational homogenization, a representative volume element is taken from the predefined fiber-volume ratio, and modelled with finite element mesh. Finally, the equivalent CTEs are obtained by applying periodic boundary condition. To verify the performance of the proposed method, the results obtained are compared with those by the existing methods and test results. Additionally, the thermal pointing error analysis for star tracker support structure is conducted and its accuracy is estimated according to CTE prediction schemes.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.4
• /
• pp.379-384
• /
• 2009

Epoxy resin based encapsulants are widely used in semiconductor packaging applications. Epoxy resin based encapsulants are often subject to crack or delamination during the reliability test due to the thermal stress caused by high modulus nature of epoxy resins. Epoxy functional siloxanes are often added into epoxy resin to reduce the modulus so that the thermal stress can be reduced. Epoxy functional siloxanes, additives for reduced modulus, were synthesized and added into the curable epoxy resins. The modulus and the coefficient of thermal expansion (CTE) were also measured to investigate the thermal stress and to see whether the epoxy functional siloxane adversely affects the CTE or not. As a result, around 26% to 72% of thermal stress reduction was observed with no adverse effect on CTE.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.58-62
• /
• 2000

The fabrication process and analysis of thermal properties of 50~76vo1% SiCp/Al metal matrix composites(MMCs) for heatsink materials in electronic packaging were investigated. The 50~76vo1% SiCp/Al MMCs fabricated by pressure infiltration casting process showed that thermal conductivities were 85~170W/mK and coefficient of thermal expansion(CTE) were ranged 10~6ppm1k. Specially, the thermal conductivity and CTE of 71vo1%SiCp/Al MMCs were ranged 115~156W/mK and 6~7ppm/K. respectively, which showed a improved thermal properties than the conventional electronic packaging materials such as ceramics and metals.