• ETRI Journal
• /
• v.36 no.1
• /
• pp.151-154
• /
• 2014

A novel frequency-switchable antenna that uses PIN diodes and a composite right- and left-handed transmission line (CRLH TL) is proposed. The CRLH TL provides multi-order resonance, including a zeroth-order resonance (ZOR), and its shunt stub determines the ZOR frequency. Thus, the resonant frequency is arbitrarily chosen by lumped chip inductors on the shunt stub. Two prototypes are designed using different chip inductors while maintaining the antenna geometries. Antenna #1 can switch the resonant frequency from 1.8 GHz to 2.3 GHz. Antenna #2 can switch its resonance from 0.9 GHz to 2.3 GHz.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.81-82
• /
• 2007

This paper presents a WLAN band active monopole antenna which is made of a CPW-fed monopole antenna and a low noise amplifier implemented on single-layer low-temperature co-fired ceramic (LTCC) substrate. Planar active antenna measure return loss and power test. (drain voltage = 4V, gate voltage = -0.6V). The bandwidth, is 540MHz, return loss is -38dB.

• ETRI Journal
• /
• v.41 no.2
• /
• pp.262-269
• /
• 2019

This paper introduces a low-cost, high-performance mmWave antenna array module at 77 GHz. Conventional waveguide transitions have been replaced by 3D CPW-microstrip transitions which are much simpler to realize. They are compatible with low-cost substrate fabrication processes, allowing easy integration of ICs in 3D multi-chip modules. An antenna array is designed and implemented using multilayer coupled-fed patch antenna technology. The proposed $16{\times}16$ array antenna has a fractional bandwidth of 8.4% (6.5 GHz) and a 23.6-dBi realized gain at 77 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.2
• /
• pp.69-75
• /
• 2007

In this paper, a single plane wide band microstrip antenna for integrated circuit is designed and fabricated. A new configuration for a wide bandwidth is proposed. This antenna consists of two folded microstrip monopoles, which are fed by a coplanar waveguide (CPW). Therefore In this paper is folded terminal part of dual microstrip line for variable reactance value. As a result compared the proposed folded dual microstrip monopole antenna with established dual microstrip monopole antennas, the proposed antenna can widen bandwidth more then about over 1[GHz. The characteristics of the proposed antenna were analyzed by using an FDTD methods. The proposed antenna has $1.98{\sim}4.05GHz$ bandwidth for using ISM, Wibro and DMB band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.10
• /
• pp.1084-1090
• /
• 2009

This paper presents a balun consisting of a T-junction, a Right/Left Handed Transmission line(RLH-TL), and a conventional Right Handed(RH) line. It is assumed that the RLH-TL consists of N unit-cells. We provide closed-form solutions and design a very compact wideband(80 %) balun using CPW lines based on the obtained solutions. Then, we propose a capacitively loaded loop antenna designed for a uniform current distribution. The antenna resistance of the proposed antenna at resonance is about 204 ohms. The length of the unit cell is about $\lambda/12$(total length: $1\;\lambda$). The magnetic field generated from the proposed antenna is stronger than that of the conventional one by as much as 20 dB. We used a coplanar strip line(CPS) to combine the loop antenna and balun. The proposed antenna may be used as a near field UHF RFID reader antenna.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.6
• /
• pp.61-70
• /
• 1999

An optical switch composed of three-identical, equally-spaced $Ti:LinbO_3$ waveguides and overlaid Al electrodes of CPW structure was designed and fabricated. Patterned Ti was diffused into z-cut $LinbO_3$ substrates at $1025^{\circ}C$ for 6 hours to make a three-waveguide directional coupler. $SiO_2$ buffer layer of $1.2{\mu}m$ was grown by the PECVD to reduce the propagation loss of TM mode, and Al electrodes were built on the layer for switching the guided beam. For an incident beam of ${\lambda}=1.3{\mu}m$, almost perfect optical coupling between two outer waveguides was observed. When an electric field was applied to detune the three waveguides anti-symmetrically, the optical switching phenomenon was successfully confirmed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.5
• /
• pp.516-521
• /
• 2011

In this paper, an inverted-triangle patch UWB antenna with an uneven ground planes and an inverted T-slot for 5 GHz WLAN band rejection is presented. The operating bandwidth of the proposed antenna fed with the CPW line is expanded from 3.1 GHz to 10.6 GHz for about -10 dB return loss using three angular parameters correlated to the main patch and the ground plane. The fabricated antenna on Taconic RF-60A substrate with 6.16 relative dielectric constant and 0.64 mm thickness has a main antenna patch size of 36 mm${\times}$19.5 mm. The measured results show return losses of about -10 dB and nearly omni-directional radiation patterns. The proposed UWB antenna has advantages of easily adjustable impedance characteristics by the three angular parameters and easily accomplishable band rejection characteristics by the inverted T-slot.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.2
• /
• pp.393-400
• /
• 2015

As the development and distribution of the intelligent transport system is spreading recently and some of the services are commercialized through a pilot project, interest in DSRC with high utilization is increasing and antennas for roadside and on board equipment are being studied. A single patch was used for a vehicle antenna due to the requests of miniaturization of size, but there was performance degradation in most cases due to miniaturization. In addition, some methods to improve performance have been used in the antennas that were previously researched using the arrays, but they have the disadvantages of bulkiness in size of the antennas when using the arrays. Therefore, in this paper, the CPW fed microstrip patch antenna with the simple structure of being compact and easy to produce, which can be used in the OBU of DSRC, was designed.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.8
• /
• pp.42-50
• /
• 2007

This paper presents design methods for dual-frequency(2.4/5.8GHz) active receiving antennas. The proposed active receiving antennas are designed to interconnect the output port of a wideband antenna to the input port of an active device of High Electron Mobility Transistor directly and to receive RF signals of 2.4GHz and 5.2GHz simultaneously where the impedance matching conditions are optimized by adjusting the length of $1/20{\lambda}_0$(@5.8GHz) CPW transmission line in the planar antenna The bandwidth of implemented dual-frequency active receiving antennas is measured in the range of 2.0GHz to 3.1GHz and 5.25GHz to 5.9GHz. Gains are measured of 17.0dB at 2.4GHz and 15.0dB at 5.2GHz. The measured noise figure is 1.5dB at operating frequencies.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.8
• /
• pp.1796-1803
• /
• 2013

In this paper, a novel particle swarm optimization method based on IE3D is used to design a mobile communication microstrip patch antenna. The aim of the paper is to design and fabricate an inset fed rectangular microstrip antenna and study the effect of antenna dimensions length (L), width (W) and substrate parameters relative dielectric constant (${\varepsilon}r$), substrate thickness on radiation parameters of band width. PSO algorism was applied to IE3D, low resistance against, band width and advantage, were improved.